Posted: Mon Jan 16, 2023 19:42 Post subject: New Build - 01/16/2023 - r51362
Welcome to Marvell r51362 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 12 Dec 2007 Posts: 780 Location: Pittsburgh, PA USA
Posted: Tue Jan 17, 2023 21:10 Post subject:
Router/Version: WRT1900AC v1
File/Kernel: DD-WRT v3.0-r51362 std (01/16/23)
Previous/Reset: DD-WRT v3.0-r51306 std (01/15/23), No reset this time, attempted IPV6 in DDNS (he.net)
Mode/Status: Gateway (SFE enabled), Access Point, IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS, OpenVPN server, Wireguard Server, Privoxy
Issues/Errors:
Up 23 hours, nperf.com shows expected ISP speeds, both wired and wireless. OpenVPN, Wireguard, DOT, and Privoxy all working as expected.
Enabled IPV6 in the DDNS tab for he.net. Got the following errors:
Code:
In-a-dyn version 2.10.0 -- Dynamic DNS update client.
Update forced for alias vpn.mydomain.tld, new IP# xx.6.yy.4
Update forced for alias vpn.mydomain.tld, new IP# xx.6.yy.4
Fatal error in DDNS server response:
[200 OK]
Updating cache for vpn.mydomain.tld
Error response from DDNS server, ignoring ...
I just went in and added a dynamic AAAA record in the dns.he.net control panel. It may need time to replicate in their system.
Joined: 01 Feb 2016 Posts: 54 Location: Oregon, U.S.
Posted: Fri Feb 03, 2023 8:25 Post subject:
Router/Version: WRT1900ACv1
Kernel: Linux 4.9.337 #3601 SMP Mon Jan 16 04:42:54 +07 2023 armv7l
File: https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2023/01-16-2023-r51362/linksys-wrt1900ac/factory-to-ddwrt.bin
Previous/Reset: Install to partition #2 from OEM Linksys firmware
Mode/Status: Expected to be Gateway device
Issues/Errors: Factory-to-ddwrt.bin would successfully upload but would not boot. It would try to start five time then switch back to OEM partition.
After several failed attempts I tried installing factory-to-ddwrt.bin using the serial recovery method. I never got this image to successfully boot. I used factory-to-ddwrt.bin for R48081 to install from OEM F/W then flashed ddwrt-linksys-wrt1900ac-webflash-r51362.bin onto the same partition to successfully finish the install.
This is what I captured on the serial port when the device reset.
It did this five time then rebooted into the OEM firmware on Partition#1.
-------------------------------------------------------------------------
## Booting kernel from Legacy Image at 02000000 ...
Image Name: DD-WRT
Created: 2022-11-08 22:42:41 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2195518 Bytes = 2.1 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.332 (root@server2) (gcc version 11.1.0 (OpenWrt GCC 11.1.0 r16904-a4e2766a5b) ) #3511 SMP Wed Nov 9 05:38:34 +07 2022
[ 0.000000] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt:Machine model: Linksys WRT1900AC
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 12 pages/cpu s18316 r8192 d22644 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200console=ttyS0,115200 mtdparts=armada-nand:1024K(uboot)ro,256K(u_env),256K(s_env),1m@9m(devinfo),40m@10m(kernel),37m@13m(rootfs),40m@50m(alt_kernel),37m@53m(alt_rootfs),80m@10m(ubifs),-@90m(syscfg) root=/dev/mtdblock5 ro rootfstype=jffs2 init=/sbin/init
[ 0.000000] Bootloader command line (ignored): console=ttyS0,115200 mtdparts=armada-nand:1024K(uboot)ro,256K(u_env),256K(s_env),1m@9m(devinfo),40m@10m(kernel),37m@13m(rootfs),40m@50m(alt_kernel),37m@53m(alt_rootfs),80m@10m(ubifs),-@90m(syscfg) root=/dev/mtdblock5 ro rootfstype=jffs2 init=/sbin/init
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 251960K/262144K available (5120K kernel code, 170K rwdata, 904K rodata, 1024K init, 369K bss, 10184K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0600000 (6112 kB)
[ 0.000000] .init : 0xc0700000 - 0xc0800000 (1024 kB)
[ 0.000000] .data : 0xc0800000 - 0xc082aa60 ( 171 kB)
[ 0.000000] .bss : 0xc082c000 - 0xc088859c ( 370 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Aurora cache controller enabled, 32 ways, 2048 kB
[ 0.000000] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a69ef12
[ 0.000000] Switching to timer-based delay loop, resolution 40ns
[ 0.000005] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.000016] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000254] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.000267] pid_max: default: 32768 minimum: 301
[ 0.000334] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000343] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000664] CPU: Testing write buffer coherency: ok
[ 0.000825] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001109] Setting up static identity map for 0x100000 - 0x100058
[ 0.001348] mvebu-soc-id: MVEBU SoC ID=0x7823, Rev=0x2
[ 0.001443] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.002000] Booting CPU 1
[ 0.004386] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.004458] Brought up 2 CPUs
[ 0.004469] SMP: Total of 2 processors activated (100.00 BogoMIPS).
[ 0.007906] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[ 0.008007] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.008020] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.008061] pinctrl core: initialized pinctrl subsystem
[ 0.008871] NET: Registered protocol family 16
[ 0.009098] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.051162] SCSI subsystem initialized
[ 0.052427] clocksource: Switched to clocksource armada_370_xp_clocksource
[ 0.053094] NET: Registered protocol family 2
[ 0.053222] IP idents hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.053555] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.053576] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.053598] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.053632] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.053647] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.053741] NET: Registered protocol family 1
[ 0.055535] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 0.060806] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.064056] io scheduler noop registered
[ 0.064065] io scheduler deadline registered (default)
[ 0.064709] armada-xp-pinctrl f1018000.pin-ctrl: registered pinctrl driver
[ 0.066052] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00
[ 0.066066] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 0.066075] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff]
[ 0.066084] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.066605] PCI: bus0: Fast back to back transfers disabled
[ 0.066616] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.066628] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.066638] pci 0000:00:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.067016] PCI: bus1: Fast back to back transfers disabled
[ 0.067301] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:02.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 0.067422] PCI: bus2: Fast back to back transfers disabled
[ 0.067800] PCI: bus3: Fast back to back transfers disabled
[ 0.067999] pci 0000:00:01.0: BAR 8: assigned [mem 0xf8000000-0xf80fffff]
[ 0.068010] pci 0000:00:02.0: BAR 8: assigned [mem 0xf8200000-0xf83fffff]
[ 0.068021] pci 0000:00:03.0: BAR 8: assigned [mem 0xf8400000-0xf85fffff]
[ 0.068033] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf8007fff 64bit]
[ 0.068050] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.068061] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff]
[ 0.068075] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8200000-0xf82fffff 64bit pref]
[ 0.068093] pci 0000:02:00.0: BAR 2: assigned [mem 0xf8300000-0xf83fffff 64bit pref]
[ 0.068108] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 0.068118] pci 0000:00:02.0: bridge window [mem 0xf8200000-0xf83fffff]
[ 0.068131] pci 0000:03:00.0: BAR 0: assigned [mem 0xf8400000-0xf84fffff 64bit pref]
[ 0.068147] pci 0000:03:00.0: BAR 2: assigned [mem 0xf8500000-0xf85fffff 64bit pref]
[ 0.068162] pci 0000:00:03.0: PCI bridge to [bus 03]
[ 0.068171] pci 0000:00:03.0: bridge window [mem 0xf8400000-0xf85fffff]
[ 0.068589] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.101159] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 0.101277] mv_xor f10f0900.xor: Marvell shared XOR driver
[ 0.123106] mv_xor f10f0900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 0.123313] serial8250_init
[ 0.123321] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.123783] console [ttyS0] disabled
[ 0.143894] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 19, base_baud = 15625000) is a 16550A
[ 0.846348] console [ttyS0] enabled
[ 0.850400] pxa3xx-nand f10d0000.nand: This platform can't do DMA on this device
[ 0.858313] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[ 0.864704] nand: AMD/Spansion S34ML01G1
[ 0.868640] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.876245] pxa3xx-nand f10d0000.nand: ECC strength 16, ECC step size 2048
[ 0.883441] Bad block table found at page 65472, version 0x01
[ 0.889730] Bad block table found at page 65408, version 0x01
[ 0.895771] nand_read_bbt: bad block at 0x000000c80000
[ 0.901065] found commandline
[ 0.904073] rename part 5 to ubi[ 0.907175] 10 ofpart partitions found on MTD device pxa3xx_nand-0
[ 0.913390] Creating 10 MTD partitions on "pxa3xx_nand-0":
[ 0.918894] 0x000000000000-0x000000100000 : "u-boot"
[ 0.924446] 0x000000100000-0x000000140000 : "u_env"
[ 0.929849] 0x000000140000-0x000000180000 : "s_env"
[ 0.935276] 0x000000900000-0x000000a00000 : "devinfo"
[ 0.940859] 0x000000a00000-0x000003200000 : "linux"
[ 0.946511] 0x000000d00000-0x000003200000 : "ubi"
[ 0.951948] 0x000003200000-0x000005900000 : "linux2"
[ 0.957692] 0x000003500000-0x000005900000 : "rootfs2"
[ 0.963533] mtd: partition "rootfs" set to be root filesystem
[ 0.969564] magic 9DDA47D0 vs 73717368
[ 0.973435] split_squashfs: no squashfs found in "pxa3xx_nand-0"
[ 0.979461] 0x000005900000-0x000005940000 : "nvram"
[ 0.984961] 0x000005a00000-0x000007f00000 : "ddwrt"
[ 0.990780] armada-xp-pinctrl f1018000.pin-ctrl: unsupported function spi on pin mpp36
[ 0.998749] armada-xp-pinctrl f1018000.pin-ctrl: unsupported function spi on pin mpp37
[ 1.006705] armada-xp-pinctrl f1018000.pin-ctrl: unsupported function spi on pin mpp38
[ 1.014657] armada-xp-pinctrl f1018000.pin-ctrl: unsupported function spi on pin mpp39
[ 1.022607] pinctrl core: failed to register map default (0): invalid type given
[ 1.030027] orion_spi: probe of f1010600.spi failed with error -22
[ 1.037177] mvneta_bm f10c0000.bm: Buffer Manager for network controller enabled
[ 1.047439] mvneta f1070000.ethernet eth0: Using random mac address 7a:df:07:0e:9a:d2
[ 1.057398] mvneta f1074000.ethernet eth1: Using random mac address ee:81:0c:be:ee:21
[ 1.065356] PPP generic driver version 2.4.2
[ 1.069725] PPP BSD Compression module registered
[ 1.074461] PPP Deflate Compression module registered
[ 1.079537] PPP MPPE Compression module registered
[ 1.084351] NET: Registered protocol family 24
[ 1.088819] i2c /dev entries driver
[ 1.093634] trying to register driver cpufreq-dt
[ 1.098323] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19
[ 1.106379] cpu cpu1: opp_list_debug_create_link: Failed to create link
[ 1.113032] cpu cpu1: _add_opp_dev: Failed to register opp debugfs (-12)
[ 1.123999] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 1.131373] GACT probability NOT on
[ 1.134950] Mirror/redirect action on
[ 1.138635] Simple TC action Loaded
[ 1.142569] netem: version 1.3
[ 1.145653] u32 classifier
[ 1.148366] Performance counters on
[ 1.152210] input device check on
[ 1.155895] Actions configured
[ 1.159311] Netfilter messages via NETLINK v0.30.
[ 1.164220] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[ 1.170680] nf_conntrack_rtsp v0.7 loading
[ 1.174944] xt_time: kernel timezone is -0000
[ 1.179442] gre: GRE over IPv4 demultiplexor driver
[ 1.184666] nf_nat_rtsp v0.7 loading
[ 1.188268] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.193831] NET: Registered protocol family 17
[ 1.198351] Bridge firewalling registered
[ 1.202373] 8021q: 802.1Q VLAN Support v1.8
[ 1.206669] Registering SWP/SWPB emulation handler
[ 1.213559] searching for nvram
[ 1.216745] nvram size = 262144
[ 1.283429] nvram empty
[ 1.286393] no valid UBI magic found inside mtd5
[ 1.291223] mvsw61xx 1000000003.mvsw61xx: Found MV88E6172 at f1072004.mdio-mii:10
[ 1.298768] mvsw61xx 1000000003.mvsw61xx: Using direct addressing
[ 1.339671] VFS: Cannot open root device "ubiblock0_0" or unknown-block(0,0): error -6
[ 1.347647] Please append a correct "root=" boot option; here are the available partitions:
[ 1.356053] 1f00 1024 mtdblock0 [ 1.360077] (driver?)
[ 1.362473] 1f01 256 mtdblock1 [ 1.366496] (driver?)
[ 1.368873] 1f02 256 mtdblock2 [ 1.372910] (driver?)
[ 1.375289] 1f03 1024 mtdblock3 [ 1.379311] (driver?)
[ 1.381687] 1f04 40960 mtdblock4 [ 1.385725] (driver?)
[ 1.388104] 1f05 37888 mtdblock5 [ 1.392126] (driver?)
[ 1.394520] 1f06 39936 mtdblock6 [ 1.398542] (driver?)
[ 1.400920] 1f07 36864 mtdblock7 [ 1.404956] (driver?)
[ 1.407335] 1f08 256 mtdblock8 [ 1.411357] (driver?)
[ 1.413749] 1f09 37888 mtdblock9 [ 1.417772] (driver?)
[ 1.420147] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 1.428443] CPU1: stopping
[ 1.431165] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.9.332 #3511
[ 1.437448] Hardware name: Marvell Armada 370/XP (Device Tree)
[ 1.443295] Backtrace:
[ 1.445777] [<c010f63c>] (dump_backtrace) from [<c010f994>] (show_stack+0x18/0x1c)
[ 1.453370] r7:00000001 r6:60000193 r5:00000000 r4:c0816990
[ 1.459052] [<c010f97c>] (show_stack) from [<c0310474>] (dump_stack+0x94/0xa8)
[ 1.466300] [<c03103e0>] (dump_stack) from [<c01120ac>] (handle_IPI+0xf0/0x198)
[ 1.473629] r7:00000001 r6:00000000 r5:cf865f78 r4:c082c278
[ 1.479306] [<c0111fbc>] (handle_IPI) from [<c0101738>] (armada_370_xp_handle_irq+0x13c/0x17c)
[ 1.487942] r7:00000010 r6:cf865f78 r5:c085e79c r4:00000000
[ 1.493619] [<c01015fc>] (armada_370_xp_handle_irq) from [<c010fcb8>] (__irq_svc+0x58/0x74)
[ 1.501991] Exception stack(0xcf865f78 to 0xcf865fc0)
[ 1.507057] 5f60: c0810d80 00000000
[ 1.515258] 5f80: cfddf2b4 c0119714 cf864000 c080442c c080447c 00000001 0000406a 562f5842
[ 1.523459] 5fa0: 00000000 cf865fdc cf865fc8 cf865fc8 c010bd48 c0164de8 60000013 ffffffff
[ 1.531661] r9:cf864000 r8:0000406a r7:cf865fac r6:ffffffff r5:60000013 r4:c0164de8
[ 1.539431] [<c0164d1c>] (cpu_startup_entry) from [<c0111d28>] (secondary_start_kernel+0x154/0x160)
[ 1.548501] r7:c082c288 r4:c0812290
[ 1.552089] [<c0111bd4>] (secondary_start_kernel) from [<00101808>] (0x101808)
[ 1.559330] r5:00000055 r4:0f85806a
[ 1.562923] Rebooting in 5 seconds..
Joined: 01 Feb 2016 Posts: 54 Location: Oregon, U.S.
Posted: Fri Feb 03, 2023 9:14 Post subject:
Observation #2
Router/Version: WRT1900ACv1
Kernel: Linux 4.9.337 #3601 SMP Mon Jan 16 04:42:54 +07 2023 armv7l
File: https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2023/01-16-2023-r51362/linksys-wrt1900ac/factory-to-ddwrt.bin
Previous/Reset: Install to partition #2 from OEM Linksys firmware
Mode/Status: Gateway, SFE-Disabled, Access Point, Entware, IPv4, NAS & Local FTP, Two Virtual WLANs, DNS Filtering via SafeDNS.
Issues/Errors: Device will show that it has an address assigned to the WAN port even when cable is disconnected from WAN port.
After the router boots successfully, it receives a WAN IP address via DHCP from a ADTRAN ONT device connected to ISP fiber optic network. Unplug the ethernet cable from the WAN port. The router continues to show that it has a WAN IP Address which will not go away until you visit Status/WAN and click DHCP Release button, then the WAN IPV4 changes to 0.0.0.0 as it should. Plug the cable back into the WAN port, the WAN is assigned an IP via DHCP. You can now repeat the steps above with the same results.
Other than this I have not experienced any problems or errors.
Any suggestions or requests how I could log this.
So far only thing I have to offer is this screen shot.
