Posted: Wed Dec 14, 2022 15:28 Post subject: New Build - 12/14/2022 - r51024
Welcome to Marvell r51024 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 12 Dec 2007 Posts: 782 Location: Pittsburgh, PA USA
Posted: Wed Dec 14, 2022 19:00 Post subject:
Router/Version: WRT1900AC v1
File/Kernel: DD-WRT v3.0-r51024 std (12/14/22)
Previous/Reset: DD-WRT v3.0-r51011 std (12/12/22), No reset this time, but config change.
Mode/Status: Gateway (SFE enabled), Access Point, IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS, OpenVPN server, Wireguard Server, Privoxy
Issues/Errors:
Removed the lines in the firewall script that I added for the last build and did the upgrade without reset. DNS and IPV6 are both working perfectly. _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r51024 std (12/14/22)
Kernel Version Linux 4.9.335 #3552 SMP Wed Dec 14 15:03:06 +07 2022 armv7l
Current Time Thu, 15 Dec 2022 07:31:29
Uptime 10:58
update- browser-waterfox,I switched from partition 1 from Linksys firmware , browser waterfox
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On - Ok
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
Port Forwarding - Ok,
USB - System Log -Ok
Schedule Reboot - At a Set Time - On
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC/N, Width VHT 80 Mhz-Wireless Channel-36,Short GI, Short Preamble,Single User Beamforming, Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES, Regulatory Domain Romania , all-ok
Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-N, Width VHT 40 Mhz-Wireless Channel-6, Extension Channel Lower,Short Preamble, Short GI , Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES)all-ok
I don't know if this is a problem, but the ping to the wifi router is very high!
in the attached link there are two videos on storage.rcs-rds.ro
https://s.go.ro/275kcsvj _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt