Posted: Sun Nov 06, 2022 11:06 Post subject: New Build - 11/06/2022 - r50814
Welcome to Atheros r50814 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Netgear Nighthawk X10 R9000
Firmware Version DD-WRT v3.0-r50814 std (11/06/22)
Kernel Version Linux 4.9.331 #652 SMP Sat Oct 29 15:01:44 +07 2022 armv7l
Current Time Sun, 06 Nov 2022 05:01:15
Uptime 3 min
GUI over 50595
Reset: no
Issues: none
Looks like radvd is functioning correctly. IPv6 protocol is active!
Joined: 06 Feb 2020 Posts: 167 Location: Maharashtra, India
Posted: Sun Nov 06, 2022 13:07 Post subject:
Router/Version: Netgear R7800
Firmware: DD-WRT v3.0-r50814 std (11/06/22)
Kernel: Linux 4.9.331 #1334 SMP Sun Nov 6 05:03:00 +07 2022 armv7l
File/Upload: dd-wrt-webupgrade.bin / Upload using CLI
Mode: Gateway/AP
Reset: No Previous: DD-WRT v3.0-r50474 std (10/11/22)
Setup Using: PPPOE, 2.4 GHz, 5.0 GHz, IPv4, DNSMasq, NTP TimeSync, WireGuard, Samba
Status: Stable, Working Fine ; running DD-WRT firmware type for 2.4ghz & 5ghz, uptime 1+ Hrs.
One observation since build 50500, anything added in additional options in Dnsmasq infrastructure are removed. Need to add them back.
writing new firmware with "write dd-wrt-webupgrade.bin linux &" command
though I had tried all build since 50500 except 50786, reverted back everytime to 50474.
Thank you BrainSlayer for Wonderful firmware.
Thanks all Guru for your help in forums.
Last edited by abhijitat on Sun Nov 06, 2022 13:10; edited 1 time in total
Status: Up and running for 2 hours, basic setup as Gateway, static leases, port forwarding DDNS, WOL 2,4GHz, VAP for IoT, 5Ghz (Vanilla Firmware, Disabled Airtime), DDNS (Inadyn) to freedns.afraid.org.
On demand governor with minimum 800 MHz
Joined: 18 Mar 2014 Posts: 12884 Location: Netherlands
Posted: Sun Nov 06, 2022 13:35 Post subject:
Router Model: Linksys EA8500
Firmware Version: DD-WRT v3.0-r50814M Community Build by EGC (11/06/22)
Upgraded from: DD-WRT v3.0-r50484M Community Build by EGC (10/12/22)
Reset: No not this time
Status: Up and running for 2 hours, basic setup as Gateway, static leases, 2.4 GHz and 5 GHz switched off, OpenVPN server working, WireGuard Server working (multiple clients e.g. phone, laptop and site-to-site connection with remote location), NAS and Samba working, Avahi and Avahi-utils working.
Linksys EA8500...main gateway
DD-WRT v3.0-r50814 std (11/06/22)
Linux 4.9.331 #1332 SMP Sat Nov 5 18:15:26 +07 2022 armv7l
GUI install over r50786
all good
#
Netgear WNDR3700 V4
DD-WRT v3.0-r50814 std (11/06/22)
Linux 3.18.140-d6 #157286 Sun Nov 6 04:30:29 -00 2022 mips
GUI install over r50786
all good
Joined: 03 Nov 2015 Posts: 317 Location: Florida, USA
Posted: Sun Nov 06, 2022 15:42 Post subject:
Router: Linksys ea8500 ..WDS AP
Firmware: DD-WRT v3.0-r50814 std (11/06/22)
Kernel: Linux 4.9.331 #1332 SMP Sat Nov 5 18:15:26 +07 2022 armv7l
Reset: NO ... Upgraded from r50786
Mode: 2.4 GHz only ....Firmware type .. DD-WRT
Errors: NONE
Router: Linksys ea8500 ..WDS Stations ... X (2)
Firmware: DD-WRT v3.0-r50814 std (11/06/22)
Kernel: Linux 4.9.331 #1332 SMP Sat Nov 5 18:15:26 +07 2022 armv7l
Reset: NO ... Upgraded from r50786
Mode: 2.4 GHz only ....Firmware type .. DD-WRT
Errors: NONE
Swift upgrades... No glinches ...Thanks DEVs _________________ ......All GOOD here... Just Handshakes and Time Stamps !......
Router/Version: Archer C7-v5
File/Kernel: tplink_archer-c7-v5.bin
Previous/Reset: r49599 / yes
Mode/Status: Gateway/AP
Issues/Errors: On every build after r49599 I'm having the same problem where Im not reaching the full WAN connection speed over WiFi. LAN cable speedtest is fine.
Rolling back to r49599 and everything is fine.
I dont know what is changed after r49599. _________________
The iperf test was Lan to Lan. The transfer was 50 mbit because the client has 65 Mbit Wi-Fi card. That's not the problem...
My advertised internet speed is 25 Mbit
With the older builds I'm getting the full 25 Mbit and with the latest build I'm getting 18-21 Mbit.
I'm guessing that the client is old. In any case, I think there is a setting that is different between the builds. _________________ Netgear R9000
DD-WRT v3.0-r55819 std (04/17/24)
Linux 4.9.337 #722 SMP Wed Apr 17 04:16:49 +07 2024 armv7l
Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
CloudFlare, no SFE, SmartDNS, no QoS
2.4GHz: Vanilla, Airtime Fairness, NG-Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
5GHz: Vanilla, Airtime Fairness, AC/N Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/35Mbps