Posted: Mon Oct 31, 2022 12:26 Post subject: New Build - 10/31/2022 - r50755
Welcome to Atheros r50755 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Linksys EA8500...main gateway
DD-WRT v3.0-r50755 std (10/31/22)
Linux 4.9.331 #1320 SMP Sat Oct 29 17:58:46 +07 2022 armv7l
scp 'firmware.bin' install over r50671
all ok
#
Netgear WNDR3700 V4
DD-WRT v3.0-r50755 std (10/31/22)
Linux 3.18.140-d6 #156902 Mon Oct 31 14:15:09 +07 2022 mips
scp 'firmware.bin' install over r50671
all ok
Update method: SSH / CLI using PuTTY
Router/Version: Netgear R9000 Nighthawk X10
File/Kernel: DD-WRT v3.0-r50755 std (10/31/22) Previous/Reset: DD-WRT v3.0-r50671 std (10/26/22) / No
Mode/Status: Gateway / Working Normally
Issues/Errors: Radio Status: "Error" on 2.4MHz wifi
The 2.4 MHz radio is working and I don't see anything in the logs, but the Wireless status page shows "Error". If I refresh, it goes back to Active but then changes to Error after 3 seconds. _________________ Netgear R9000
DD-WRT v3.0-r55460 std (03/25/24)
Linux 4.9.337 #715 SMP Mon Mar 25 06:15:53 +07 2024 armv7l
Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
CloudFlare, no SFE, SmartDNS, no QoS
2.4GHz: Vanilla, Airtime Fairness, NG-Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
5GHz: Vanilla, Airtime Fairness, AC/N Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/35Mbps
Joined: 12 Dec 2007 Posts: 764 Location: Pittsburgh, PA USA
Posted: Mon Oct 31, 2022 13:53 Post subject:
Quote:
The 2.4 MHz radio is working and I don't see anything in the logs, but the Wireless status page shows "Error". If I refresh, it goes back to Active but then changes to Error after 3 seconds.
I'm seeing the same on a Netgear R7800 as well as on two WRT1900ACs. Doesn't seem to be related to the platform since the WRT1900AC is Marvell. _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
Joined: 12 Dec 2007 Posts: 764 Location: Pittsburgh, PA USA
Posted: Mon Oct 31, 2022 14:25 Post subject:
The error is cosmetic only, as I'm seeing it on all three devices, both on wlan0 and wlan1, but all of my devices are still connected. _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
Joined: 31 Jul 2021 Posts: 2146 Location: All over YOUR webs
Posted: Mon Oct 31, 2022 14:25 Post subject:
ho1Aetoo wrote:
Edit: seems to be a problem with the translation
with english language setting I get an error too
sigh looking into it now, cant br strings because the Active is shown and switches to error later, if it were strings it would show undefined or Unknown.
PS...
So Switch to Portuguese all was OK,
Swicthed to German, it was OK then instead of error showed the Portuguese word for active. Switched back to English and Active became Error.
(We dont have a Capitalized Error String anywhere.)
Joined: 03 Nov 2015 Posts: 316 Location: Florida, USA
Posted: Mon Oct 31, 2022 14:28 Post subject:
Router: Linksys ea8500 ..WDS AP
Firmware: DD-WRT v3.0-r50755 std (10/31/22)
Kernel: Linux 4.9.331 #1320 SMP Sat Oct 29 17:58:46 +07 2022 armv7l
Reset: NO ... GUI upgrade from r50595
Mode: 2.4 GHz only ....Firmware type .. DD-WRT
Errors: NONE
Router: Linksys ea8500 ..WDS Stations ... X (2)
Firmware: DD-WRT v3.0-r50755 std (10/31/22)
Kernel: Linux 4.9.331 #1320 SMP Sat Oct 29 17:58:46 +07 2022 armv7l
Reset: NO ... GUI upgrade from r50595
Mode: 2.4 GHz only ....Firmware type .. DD-WRT
Errors: NONE
Uptime on last build (r50595) 7 Days 17 hrs. plus with out a single issue...Thanks Everyone !! _________________ ......All GOOD here... Just Handshakes and Time Stamps !......
Edit: seems to be a problem with the translation
with english language setting I get an error too
sigh looking into it now, cant br strings because the Active is shown and switches to error later, if it were strings it would show undefined.
yes very strange
with german language setting no errors are shown to me over a longer period of time
but as soon as i change to english it immediately shows "error" and it stays even when i change back to german
after 10min the error is gone again
Netgear Nighthawk X10 R9000
Firmware Version DD-WRT v3.0-r50755 std (10/31/22)
Kernel Version Linux 4.9.331 #652 SMP Sat Oct 29 15:01:44 +07 2022 armv7l
Current Time Mon, 31 Oct 2022 08:37:11
Uptime 1 min
GUI over 50671
Reset: no
Issues: works fine
Joined: 05 Oct 2008 Posts: 666 Location: Helsinki, Finland / nr. Alkmaar, Netherlands
Posted: Mon Oct 31, 2022 19:56 Post subject:
My R7800 on build 50755 shows all of the (applicable) 'error' messages described in previous messages. I was about to post a screen picture of the bug I first noticed, but no need to repeat, so I just confirm.