Posted: Wed Oct 26, 2022 11:56 Post subject: New Build - 10/26/2022 - r50671
Welcome to Marvell r50671 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 12 Dec 2007 Posts: 780 Location: Pittsburgh, PA USA
Posted: Wed Oct 26, 2022 13:37 Post subject:
Router/Version: WRT1900AC v1
File/Kernel: DD-WRT v3.0-r50671 std (10/26/22)
Previous/Reset: DD-WRT v3.0-r50595 std (10/23/22), No reset this time.
Mode/Status: Gateway (SFE enabled), Access Point, IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS, OpenVPN server, Wireguard Server, Privoxy
Issues/Errors:
As reported in other forums, InaDyn is broken. Log shows "Parse error in /tmp/ddns/inadyn.conf" using Custom (dyn.dns.he.net). The inadyn.conf file seems to be in a different format than the previous release (since InaDyn's been updated) but seems to be missing some parameters, notably dyndns_server_name or equivalent.
It does appear to work if I change from Custom to he.net. While this is fine for me, others using Custom may not be so lucky. _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r50671 std (10/26/22)
Kernel Version Linux 4.9.330 #3486 SMP Wed Oct 26 05:40:53 +07 2022 armv7l
Current Time Sat, 29 Oct 2022 06:54:35
Uptime 2 days, 12:20
update- browser-waterfox,I switched from r50595 without saving the settings , browser waterfox
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
https://www.nperf.com/r/3414220460967341-WxlExD3e
IPv6 Type DHCPv6 with Prefix Delegation-On
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,Wednesday at a set time 03:00
Web Access Protocol - HTTPS,
Port Forwarding - Ok,
USB - for syslog-ok
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-36,Short GI, Short Preamble,Single User Beamforming, Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES, Regulatory Domain Romania , all-ok
Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-N, Width VHT 40 Mhz-Wireless Channel-6, Extension Channel Lower,Short Preamble, Short GI , Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES)all-ok _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt