Posted: Thu Oct 13, 2022 5:20 Post subject: New Build - 10/13/2022 - r50500
Welcome to Marvell r50500 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 12 Dec 2007 Posts: 783 Location: Pittsburgh, PA USA
Posted: Thu Oct 13, 2022 17:55 Post subject:
Router/Version: WRT1900AC v1
File/Kernel: DD-WRT v3.0-r50500 std (10/13/22)
Previous/Reset: DD-WRT v3.0-r50357 std (10/5/22), No reset this time.
Mode/Status: Gateway (SFE enabled), Access Point, IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS, OpenVPN server, Wireguard Server, Privoxy
Issues/Errors:
After firmware upgrades, Wireguard client connects and can ping local IPs, but cannot access FTP, HTTP, or SMB shares. Toggling "NAT via Tunnel" and "Bypass LAN Same-Origin Policy" and hitting Apply, then switching them back and hitting Apply again fixes the issue. Fix survives reboots but must be applied after upgrade. Been the same on the last three builds. Now that I found the workaround, I stopped reverting back. _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
DD-WRT Router Model wrt1900acs v2
Firmware Version DD-WRT v3.0-r50500 std (10/13/22)
Kernel Version Linux 4.9.330 #3466 SMP Thu Oct 13 02:01:23 +07 2022 armv7l
Uptime 1:02
update- browser-waterfox,I switched from 50484 do not reset , browser waterfox
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
Port Forwarding - Ok,
USB - for syslog-ok
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-36,Short GI, Short Preamble,Single User Beamforming, Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES, Regulatory Domain Romania , all-ok
Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-N, Width VHT 40 Mhz-Wireless Channel-6, Extension Channel Lower,Short Preamble, Short GI , Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES)all-ok
I noticed an anomaly after the update, if I kept the settings, latency in ping with disconnections, after I gave restore to factory defaults everything returned to normal! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r50500 std (10/13/22)
Kernel Version Linux 4.9.330 #3466 SMP Thu Oct 13 02:01:23 +07 2022 armv7l
Current Time Sun, 16 Oct 2022 08:33:52
Uptime 2 days, 8:37
a stable and very fast version, it seems that it is better not to keep the settings when updating! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r50500 std (10/13/22)
Kernel Version Linux 4.9.330 #3466 SMP Thu Oct 13 02:01:23 +07 2022 armv7l
Current Time Sun, 16 Oct 2022 08:33:52
Uptime 3 days, 8:37
a stable and very fast version, it seems that it is better not to keep the settings when updating!
Router/Version: Linksys WRT1900ACS v2
File: ddwrt-linksys-wrt1900acsv2-webflash.bin
Firmware: DD-WRT v3.0-r50500 std (10/13/22) (prev. DD-WRT v3.0-r50484 std (10/12/22))
Kernel: Linux 4.9.330 #3466 SMP Thu Oct 13 02:01:23 +07 2022 armv7l
Mode: Gateway, SFE enabled, Wifi disabled, Wireguard for external access, WAN to DSL, samba to access USB3-ext4 SSD, Keep Alive reboot 5:00 in the morning
Reset: No
Status: Installed at release, ok. Load average 0.51, 0.18, 0.06, Temperatures CPU 81.7 °C / WL0 49.8 °C / WL1 51.5 °C - currently under load, backup is running to SSD
edit - tested flatping, no problems or interruptions seen like oliver44 mentioned.