Posted: Tue Sep 27, 2022 7:45 Post subject: New Build - 09/27/2022 - r50274
Welcome to Marvell r50274 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r50274 std (09/27/22)
Kernel Version Linux 4.9.329 #3428 SMP Tue Sep 27 02:18:44 +07 2022 armv7l
Uptime 6:55
update- browser-waterfox,I switched from version DD-WRT v3.0-r50176 (09/15/22), without resetting the settings!
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
Port Forwarding - Ok,
USB - for syslog-ok
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-36,Short GI, Short Preamble,Single User Beamforming, Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES, Regulatory Domain Romania , all-ok
Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-N, Width VHT 40 Mhz-Wireless Channel-6, Extension Channel Lower,Short Preamble, Short GI , Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES)all-ok
Issues/Errors: There is no switch config tab, only after reboot the router we have switch config ! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Joined: 12 Dec 2007 Posts: 761 Location: Pittsburgh, PA USA
Posted: Wed Sep 28, 2022 23:44 Post subject:
Router/Version: WRT1900AC v1
File/Kernel: DD-WRT v3.0-r50274 std (09/27/22)
Previous/Reset: DD-WRT v3.0-r50176 std (09/15/22), No reset this time.
Mode/Status: Gateway (SFE enabled), Access Point, IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS, OpenVPN server, Wireguard Server, Privoxy
Issues/Errors:
Getting repeated warnings in the Syslog, even though IPV6 (from ISP) is working fine
Code:
daemon.warn dnsmasq-dhcp[3765]: no address range available for DHCPv6 request via eth1
Other than that, everything is working as expected. _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
Joined: 12 Dec 2007 Posts: 761 Location: Pittsburgh, PA USA
Posted: Fri Sep 30, 2022 0:15 Post subject:
I figured it out, had "interface *" in my DNSMASQ config. Not a problem with this build, but with my recent reconfiguration. _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD