Posted: Thu Sep 15, 2022 4:29 Post subject: New Build - 09/15/2022 - r50176
Welcome to Broadcom r50176 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Try station or repeater mode but YMMV.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: Linksys WRT54GL v1.1
File/Kernel: dd-wrt.v24 mini generic r50176 / Linux 2.4.37 #69568 Thu Sep 15 01:14:19 +07 2022 mips
Previous/Reset: dd-wrt.v24 mini generic r50146 / no
Mode/Status: AP wired and wireless / Up and running for 7 hours
Issues/Errors: Nothing significant
Router/Version: Asus RT-AC3100
File: asus_rt-ac3100-firmware.trx
Kernel: Linux 4.4.302-st25 #7446 SMP Thu Sep 15 02:11:03 +07 2022 armv7l
Previous/Reset: r50146 / No reset, upgraded via GUI (https)
Mode/Status: Gateway/AP, up 12+ hours
Services Enabled: Ignore WAN DNS, DNSmasq no-resolv, QoS Enabled - FQ-Codel
Issues/Errors: No issues; Working as configured, keeping an eye on the page load issues.
---
Router/Version: ASUS RT-AC68U rev B1 (AC1900)
File: asus_rt-ac68u-firmware.trx
Kernel: Linux 4.4.302-st25 #7446 SMP Thu Sep 15 02:11:03 +07 2022 armv7l
Previous/Reset: r50146 / No reset, upgraded via GUI (https)
Mode/Status: Station Bridge, up 12+ hours
Issues/Errors: No issues; Working as configured
Thank you BS and all of the other devs who help out to make this firmware great. _________________ ASUS RT-AC3100 AP Merlin 386.12_4
ASUS RT-AC68U Media Bridge/Merlin 386.12_4 (x2)
ASUS RT-AC68U AP r54604
ASUS RT-AC68U Gateway/AP r54604
Edgerouter-4, v2.0.9-hotfix7
Netgear R8500
Firmware Version DD-WRT v3.0-r50176 std (09/15/22)
Kernel Version Linux 4.4.302-st25 #7452 SMP Thu Sep 15 03:00:52 +07 2022 armv7l
Current Time Thu, 15 Sep 2022 15:24:00
Uptime 1 min
GUI over 50146
Reset: no
Issues: none
Router/Version: Netgear R7000 Firmware: DD-WRT v3.0-r50176 std (09/15/22) Kernel: Linux 4.4.302-st25 #7446 SMP Thu Sep 15 02:11:03 +07 2022 armv7l Mode: Gateway, Wireless AP, Static Leases, Dnsmasq Caching. CTF & FA Enabled. NAT and QOS Off. All services off under Status>Sys-info. Reset: Nope. Previous: 09-10-2022-r50146 Status: Working so far, still testing. Possible issues with Dnsmasq. wl: 14E4:4360 Temperatures: CPU 66.9 °C / WL0 53.3 °C / WL1 54.5 °C Base CFE: Modified Asus ASUS RT-AC68P/ASUS RT-AC68U (C0 Model CFE V1.3.0.7) Configured as a stock R7000.
Speedtest.jpg
Description:
Speedtest Over 5.8GHz Wireless. ISP Spec: 400 Mbps Down / 25 Mbps Up.
Filesize:
62.88 KB
Viewed:
4648 Time(s)
Logs.txt
Description:
Full system logs. MAC scrubbed, password scrubbed, the fun stuff at the bottom as usual!
Joined: 01 Dec 2021 Posts: 289 Location: Maryland, United States
Posted: Sat Sep 17, 2022 14:54 Post subject:
Router/Version: Netgear R7000P
Firmware Version: DD-WRT v3.0-r50176 std (09/15/22)
Kernel Version: Linux 4.4.302-st25 #7452 SMP Thu Sep 15 03:00:52 +07 2022 armv7l
Previous/Reset: r50146 / no reset
Mode/Status: Gateway / Working
Issues/Errors: After updating to this release or rebooting the router, it takes about five minutes for the GUI to stabilize. If I look at multiple tabs before then I will lose the GUI. Clearing the cache on Firefox does not help, but after 5 minutes the GUI is stable.
Firmware: v3.0-r50176 std (09/15/22)
Router/Version: Netgear R7000 Kernel: Linux 4.4.302-st25 #7446 SMP Thu Sep 15 02:11:03 +07 2022 armv7l
Previous: v3.0-r50146 std (09/10/22)
Mode/Status: AP wired and wireless / Up and running for 2 days
Reset: Soft boot before and after upgrade
Temperatures: CPU 62.5 °C / WL0 46.9 °C / WL1 52.0 °C
Issues/Errors: Nothing significant
Updated via webif. No 'nvram erase' this time, last one was in July 2018 (r36325).
I've noticed a reduction in 5 GHz range, but that may be a local issue.
Upload and Download speeds are to ISP spec (500/500 Mbps).
Current basic R7000 setup (subject to change of course):
- Static WAN IP
- Shortcut Forwarding Engine: CTF, Flow Acceleration: Disabled
- STP - Enabled
- IPv4 only, both WAN and LAN
- LAN DHCP Enabled
- Not currently forwarding any ports
- Wireless: AP, Regulatory Domain = CANADA, wl0 Mixed (ch. 6), wl1 AC/N-Mixed (ch. 36, VHT80), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- No custom scripts
- No: ttraf, Tor, VNC, Zabbix, VPN, Radius, OpenVPN
- No: UPnP, DMZ, QoS
- No: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7