Posted: Sat Sep 10, 2022 15:52 Post subject: New Build - 09/10/2022 - r50146
Welcome to Marvell r50146 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 12 Dec 2007 Posts: 783 Location: Pittsburgh, PA USA
Posted: Sat Sep 10, 2022 18:39 Post subject:
Router/Version: WRT1900AC v1
File/Kernel: DD-WRT v3.0-r50057 std (09/03/22)
Previous/Reset: r49838 std / Full reset/reconfigure
Mode/Status: Gateway (SFE enabled), Access Point, IPV6 via Hurricane / native Verizon, Entware, DOT via Stubby, OpenVPN server, Wireguard Server, Privoxy
Issues/Errors:
DNS seems to be stable after reboot on this build, but I've only had it on for half an hour. I still notice some weirdness with IPV6. On both Hurricane tunnel (6in4) and DHCP6 with prefix delegation, after reboot, I get an incomplete IPV6 address on the router. I have to go into the IPV6 tab and hit Apply to correct (in the screenshot below, IPV4 was obfuscated, but the IPV6 doesn't appear to be valid). _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
Router Model Linksys WRT1900ACS V2
Firmware Version DD-WRT v3.0-r50146 (09/10/22)
Kernel Version Linux 4.9.327 #3404 SMP Sat Sep 10 14:22:50 +07 2022 armv7l
Uptime 30 min
update- browser-waterfox,I switched directly from the first partition from the original software Linksys,
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
Port Forwarding - Ok,
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-36,Short GI, Short Preamble,Single User Beamforming, Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES, Regulatory Domain Romania , all-ok
Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-N, Width VHT 40 Mhz-Wireless Channel-6, Extension Channel Lower,Short Preamble, Short GI , Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES)all-ok
Issues/Errors: after I finished the installation I noticed that menu from setup - Switch Config is not present, only after a reboot it reappeared!
DD-Wrt looks better and better, congratulations for everything you do!!!! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Router/Version: Linksys WRT1900ACS v2
File: ddwrt-linksys-wrt1900acsv2-webflash.bin
Firmware: DD-WRT v3.0-r50146 std (09/10/22) (prev. DD-WRT v3.0-r50057 std (09/03/22))
Kernel: Linux 4.9.327 #3404 SMP Sat Sep 10 14:22:50 +07 2022 armv7l
Mode: Gateway, SFE enabled, Wifi disabled, Wireguard for external access, WAN to DSL, samba to access USB3-ext4 SSD, Keep Alive reboot 5:00 in the morning
Reset: No
Status: Installed at release, ok. Load average 0.00, 0.00, 0.00, Temperatures CPU 77.4 °C / WL0 50.4 °C / WL1 52.0 °C
