Posted: Sat Sep 03, 2022 4:50 Post subject: New Build - 09/03/2022 - r50057
Welcome to Broadcom r50057 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Try station or repeater mode but YMMV.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 26 Mar 2013 Posts: 1748 Location: Hung Hom, Hong Kong
Posted: Sat Sep 03, 2022 12:22 Post subject:
Router Model: Netgear R7000P
Operating Mode/Setup: Gateway / 5 GHz AP VAP | Unbound USB
Unbound unable to read /jffs/etc/unbound/root.key
had to revert to previous public beta
You might need to power off then on the router after firmware upgrade.
I think DD-WRT build 50057 was not detecting /jffs/etc/ properly when starting Unbound a.k.a. recursive_dns. It got no problem picking up /jffs/etc/minidlna.conf and /jffs/etc/lighttpd.conf. I suspect they were possibly using different methods to detect /jffs, especially when /jffs was not JFFS2 but an external USB drive.
It'll better if DD-WRT just copies and uses the startup method of MiniDLNA to load Unbound.
_________________ Router: Asus RT-N18U (rev. A1)
Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!
Posted: Sat Sep 03, 2022 14:17 Post subject: Netgear Nighthawk R7000
Router/Version: Netgear R7000 Firmware: DD-WRT v3.0-r50057 std (09/03/22) Kernel: Linux 4.4.302-st25 #7235 SMP Sat Sep 3 03:18:42 +07 2022 armv7l Mode: Gateway, Wireless AP, Static Leases. CTF & FA Enabled. NAT and QOS Off. All services off under Status>Sys-info. Reset: Nope. Previous: 08-31-2022-r50012 Status: Working so far, still testing. There is something screwy with the wl driver and older clients. There is a performance issue with anyone using a PCI\VEN_14E4&DEV_43B1
based chip. wl: 14E4:4360 Temperatures: CPU 67.5 °C / WL0 54.0 °C / WL1 55.3 °C Base CFE: Modified Asus ASUS RT-AC68P/ASUS RT-AC68U (C0 Model CFE V188.8.131.52) Configured as a stock R7000.
Full system logs. MAC scrubbed, password scrubbed, the fun stuff at the bottom as usual!
Joined: 24 Feb 2013 Posts: 1625 Location: Belgrade
Posted: Sat Sep 03, 2022 16:08 Post subject:
Router/Version: Netgear R8000 using experimental build (brcmfmac driver + iw tool 5.19)
File/Kernel: Linux 4.4.302-st25 #7244 SMP Sat Sep 3 04:24:51 +07 2022 armv7l
Mode/Status: Working, using all tri bands 1300+600+1300, IPv6PD+IPv4 dul stack radvd, QoS on ipv4+ipv6 HTB+fq_CoDel, mDNS, mactelnet, NextDNS DOH from jffs, WG server(IPv4),