Posted: Wed Aug 31, 2022 5:17 Post subject: New Build - 08/31/2022 - r50012
Welcome to Broadcom r50012 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Try station or repeater mode but YMMV.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: TP-Link Archer c9 v2
File/Kernel: DD-WRT v3.0-r50012 std (08/31/22) / Linux 4.4.302-st25 #7184 SMP Wed Aug 31 02:20:51 +07 2022 armv7l
Previous/Reset: DD-WRT v3.0-r49934 std (08/28/22) / No
Mode/Status: Gateway, OpenVPN server, DDNS, static IPs, access restrictions (block kids devices at bedtime using MAC address), UPnP, port forwarding, IPv6 with prefix delegation / Up for 15mins
Issues/Errors: Access Restrictions - denying access by MAC address or IP address does not appear to work. Can anyone else confirm?
Last edited by marbss on Wed Aug 31, 2022 12:05; edited 1 time in total
Posted: Wed Aug 31, 2022 11:47 Post subject: Netgear Nighthawk R7000
marbss wrote:
Issues/Errors: Access Restrictions - denying access by MAC address does not appear to work. Can anyone else confirm?
I am having the same issues on my R7000, It does work but for whatever reason scheduled settings don't apply. If I login to the router and mash the apply button it works.
Posted: Wed Aug 31, 2022 12:03 Post subject: Re: Netgear Nighthawk R7000
twindragon6 wrote:
marbss wrote:
Issues/Errors: Access Restrictions - denying access by MAC address does not appear to work. Can anyone else confirm?
I am having the same issues on my R7000, It does work but for whatever reason scheduled settings don't apply. If I login to the router and mash the apply button it works.
Thank you @twindragon6 for confirming this. I went old school -- the kids hand in their devices after dinner
Netgear R8500
Firmware Version DD-WRT v3.0-r50012 std (08/31/22)
Kernel Version Linux 4.4.302-st25 #7188 SMP Wed Aug 31 02:46:14 +07 2022 armv7l
Current Time Wed, 31 Aug 2022 07:54:53
GUI over 49976
Reset: no
Issues: upgraded fine
Joined: 31 Jul 2021 Posts: 2146 Location: All over YOUR webs
Posted: Wed Aug 31, 2022 14:22 Post subject: Re: Netgear Nighthawk R7000
twindragon6 wrote:
marbss wrote:
Issues/Errors: Access Restrictions - denying access by MAC address does not appear to work. Can anyone else confirm?
I am having the same issues on my R7000, It does work but for whatever reason scheduled settings don't apply. If I login to the router and mash the apply button it works.
Router/Version: Asus RT-AC3100
File/Kernel: asus_rt-ac3100-firmware.trx
Previous/Reset: 49976 / No (GUI Update)
Mode/Status: Gateway/AP - Services used: Forced DNS, Qos (FQ_Codel)
Issues/Errors: None so far. Thank you BS, and the other devs that help out. I've been using DD-WRT for many years now and it has come really far with all of the updates and refreshes with the UI! _________________ ASUS RT-AC3100 AP Merlin 386.12
ASUS RT-AC68U Media Bridge/Merlin 386.12 (x2)
ASUS RT-AC68U AP r53562
ASUS RT-AC3100 Gateway/AP r53562
Edgerouter-4, v2.0.9-hotfix6
Issues/Errors: Access Restrictions - denying access by MAC address does not appear to work. Can anyone else confirm?
I am having the same issues on my R7000, It does work but for whatever reason scheduled settings don't apply. If I login to the router and mash the apply button it works.
I have 1 x set 24 hour filter to block wan on some devices and 1x 7 day filter for telemetry services. Both work without mashing anything, I haven't tried between the hours of and, but that's a 24 hour cycle only. If someone shares their setup example ill test some asap. best offer I can do.
if it works after you hit apply it might have to do with the restart code of a lot of services users complaining about DNSMasq, Unbound), the new restart code does not always do a full restart of some services if they are already running.
Router/File: Linksys WRT54GL v1.1 / DD-WRT v3.0-r50012 std-nokaid (08/31/22)
Kernel: Linux 2.4.37 #69441 Wed Aug 31 01:21:00 +07 2022 mips
Previous/Reset: 09/23/2021 - r47479 / see below
Mode/Status: WAP / see below
Issues/Errors: GUI Upgrade failed from a working setup, which is disconcerting.
I did a (h/w button) reset and started from scratch. The same issue exists as last year, where making any changes to the Switch Config tab breaks the router (no SSID nor GUI access). So I reset again (30/10/30 this time since the other methods don't remove everything [ya ya, I know...] ) and set it up as a WAP and didn't touch the swconfig.
I might try hooking up serial (I still have the case apart from messing w/ it last year) to get an upgrade log for Sebastian, but hopefully I'll instead sell it...
I plan to upgrade the (less...) old E2500's next, hopefully that goes better. _________________ #NAT/SFE/CTF: limited speed w/ DD#Repeater issues#DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo#
OPNsense x64 5050e ITX|DD: DIR-810L, 2*EA6900@1GHz, R6300v1, RT-N66U@663, WNDR4000@533, E1500@353,
WRT54G{Lv1.1,Sv6}@250|FreshTomato: F7D8302@532|OpenWRT: F9K1119v1, RT-ACRH13, R6220, WNDR3700v4
Issues/Errors: Access Restrictions - denying access by MAC address does not appear to work. Can anyone else confirm?
I am having the same issues on my R7000, It does work but for whatever reason scheduled settings don't apply. If I login to the router and mash the apply button it works.
I have 1 x set 24 hour filter to block wan on some devices and 1x 7 day filter for telemetry services. Both work without mashing anything, I haven't tried between the hours of and, but that's a 24 hour cycle only. If someone shares their setup example ill test some asap. best offer I can do.
if it works after you hit apply it might have to do with the restart code of a lot of services users complaining about DNSMasq, Unbound), the new restart code does not always do a full restart of some services if they are already running.
Just a thought
Logs.txt
Description:
Full system logs. MAC scrubbed, password scrubbed, the fun stuff at the bottom as usual!
best offer I can do.
