Posted: Mon Aug 29, 2022 4:49 Post subject: New Build - 08/29/2022 - r49976
Welcome to Broadcom r49976 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Try station or repeater mode but YMMV.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Yes, switch config page is broken. Upgraded Netgear R7000 to this build and everything work fine. Except for the mentioned Switch Config page _________________ Netgear R7000 on Build 55109
Asus AC-AC68U rev. C1 (AP) on Build 55109
Asus AC-68U rev. A1 on Build 54604
Asus AC-68U rev. A1 on Build 53339
Netgear R8500
Firmware Version DD-WRT v3.0-r49976 std (08/29/22)
Kernel Version Linux 4.4.302-st25 #7178 SMP Mon Aug 29 03:25:51 +07 2022 armv7l
Current Time Mon, 29 Aug 2022 13:46:08
Uptime 0 mi
GUI over 49934
Reset: no
Issues: upgraded fine
Router/Version: DLINK DIR885L
File/Kernel: dir885-webflash.bin / 4.4.302-st25 #7177 SMP Mon Aug 29 03:19:08 +07 2022 armv7l DD-WRT
Previous/Reset: DD-WRT v3.0-r47040 std (07/12/21)- WAS WORKING ON THIS BUILD / FULL RESET DONE
Mode/Status: Router / working
Issues/Errors: STATIC LEASES/ appear in GUI and Shell but do nothing
UPDATE
I tried r49934 and it also doesn't work.
I tried r49626 this one works perfectly with Static leases
Router/Version: Netgear 8000
File/Kernel: Linux 4.4.302-st25 #7177 SMP Mon Aug 29 03:19:08 +07 2022 armv7l
Previous/Reset: 08-15-2022-r49741 / no
Mode/Status: RIP2 router, wireguard / works
Issues/Errors: None (not counting "Setup/switch config" view as it will be taken care in next releases) _________________ Several NetGears with Broadcom and with Atheros
Mode: RIP2 Router, 2G/5G radios are active, Routed WiFi multiple SSID's/separated by IP subnets.
Remote Syslog, NTP, IPv6 management, WireGuard routed Site-2-Site VPNs