Posted: Sun Aug 28, 2022 5:57 Post subject: New Build - 08/28/2022 - r49934
Welcome to Broadcom r49934 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Try station or repeater mode but YMMV.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 18 Mar 2014 Posts: 12913 Location: Netherlands
Posted: Sun Aug 28, 2022 8:54 Post subject:
Router Model: Linksys EA6900 (XVortex CFE)
Firmware Version: DD-WRT v3.0-r49934M Community Build (08/28/22)
Kernel Version: Linux 4.4.302-st25 #1 SMP Sun Aug 28 09:18:31 CEST 2022 armv7l
Upgraded: DD-WRT v3.0-r49626M Community Build (08/03/22)via telnet (update via GUI not possible because nvram is placed on linux partition and not linux2 partition due to Xvortex CFE)
Reset: No not this time.
Configuration: Default gateway mode, 2,4GHz wireless running with unbridged VAP, 5GHz running, some static leases and some port range forwarding.
WireGuard client running with PBR.
OpenVPN client with PBR running.
NVRAM size 47K (NVRAM size should not be a problem with the Xvortex CFE)
Router/Version: Netgear R7000
File/Kernel: Linux 4.4.302-st25 #7141 SMP Sun Aug 28 00:10:07 +07 2022 armv7l
Previous/Reset: 08-24-2022-r49866 / No
Mode/Status: RIP2 Router, IPv4/IPv6, Routed WiFi
Issues/Errors: None
Previously mentioned issue with 08-24-2022-r49866 in Status/Wireless/Wireless Nodes is fixed. _________________ Several NetGears with Broadcom and with Atheros
Mode: RIP2 Router, 2G/5G radios are active, Routed WiFi multiple SSID's/separated by IP subnets.
Remote Syslog, NTP, IPv6 management, WireGuard routed Site-2-Site VPNs
Router/Version: TP-Link Archer c9 v2
File/Kernel: DD-WRT v3.0-r49934 std (08/28/22)/ Linux 4.4.302-st25 #7143 SMP Sun Aug 28 04:45:52 +07 2022 armv7l
Previous/Reset: DD-WRT v3.0-r49866 std (08/24/22) / Yes after flashing from GUI
Mode/Status: Gateway, OpenVPN server, DDNS, static IPs, access restrictions (block kids devices at bedtime using MAC address), UPnP, port forwarding, IPv6 with prefix delegation / Up for 2hrs
Issues/Errors: Access restrictions not working. Can anyone else verify this?
Netgear R8500
Firmware Version DD-WRT v3.0-r49934 std (08/28/22)
Kernel Version Linux 4.4.302-st25 #7147 SMP Sun Aug 28 05:07:55 +07 2022 armv7l
Current Time Sun, 28 Aug 2022 08:01:20
Uptime 0 min
GUI over 49866
Reset: no
Issues: upgrade fine
Posted: Mon Aug 29, 2022 1:54 Post subject: Netgear Nighthawk R7000
Router/Version: Netgear R7000 Firmware: DD-WRT v3.0-r49934 std (08/28/22) Kernel: Linux 4.4.302-st25 #7141 SMP Sun Aug 28 00:10:07 +07 2022 armv7l Mode: Gateway, Wireless AP, Static Leases. CTF & FA Enabled. NAT and QOS Off. All services off under Status>Sys-info. Reset: Nope. Previous: 08-23-2022-r49838 Status: Working so far; certain cat commands for example cat /proc/cpuinfo do not work from the Administration> Commands> Command Shell Box, still testing. wl: 14E4:4360 Temperatures: CPU 68.6 °C / WL0 54.5 °C / WL1 55.8 °C Base CFE: Modified Asus ASUS RT-AC68P/ASUS RT-AC68U (C0 Model CFE V1.3.0.7) Configured as a stock R7000.
Netgear R8500 on this version and it has bad wifi. This means you connect to the network but will have no internet access.
I have a netgear r6400 running aide by side to it with the same dd version and i it runs fine. All clients on the r8500 have internet access for a short period but then nothing.
So they then switch the the the netgear r6400
And it gets them back on the net.
The r6400 is the crappiest router i own and its for all my iot camera junk etc… and it seems to be the most reliable. No drops and consistent access to web