Posted: Wed Jul 20, 2022 10:50 Post subject: New Build - 07/20/2022 - r49531
Welcome to Marvell r49531 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r49531 std (07/20/22)
Kernel Version Linux 4.9.323 #3310 SMP Wed Jul 20 04:33:37 +07 2022 armv7l
Uptime 2:25
Load Average 1% 0.01, 0.00, 0.00
Temperatures CPU 57.5 °C / WL0 32.1 °C / WL1 33.3 °C
update- browser-waterfox,I switched directly from the first partition from the original software Linksys,
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation- DHCPv6 Server Daemon Enable Daemon, Router Advertisement Daemon (radvd)Enable Daemon,
Theme - Dracula
Schedule Reboot-on,
Web Access Protocol - HTTPS,
Port Forwarding ok,
adblock - 1.Go to Administration -> Go to Administration -> Commands. paste it in “Run Startup”
2.then in the Additional Dnsmasq options add this: addn-hosts=/tmp/mvps 3.Schedule Reboot tuesday 4.reboot router
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-36,Short GI, Short Preamble,Single User Beamforming, Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES, Regulatory Domain Romania , all-ok
Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-N/G, Width VHT 40 Mhz-Wireless Channel-6, Extension Channel Lower,Short Preamble, Short GI , Radio Scheduling, Enable-WPA2 Personal-CCMP-128 (AES)all-ok
Reset:No- just reboot
Issues/Errors-For the first time this year when I encounter problems during configuration, the apply and save buttons were inactive, only after about 10 seconds since I tried to use them they became active!
I noticed that I lost ipv6 not even a day after installation, I had to reboot the router to solve both problems, today I activated to save the system logs, if problems occur I return with the system logs, so far everything seems ok! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt