Posted: Sat Jun 04, 2022 11:50 Post subject: New Build - 06/04/2022 - r49081
Welcome to Atheros r49081 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Posted: Sat Jun 04, 2022 11:58 Post subject: r49081
Netgear Nighthawk X10 R9000
Firmware Version DD-WRT v3.0-r49081 std (06/04/22)
Kernel Version Linux 4.9.316 #632 SMP Sat Jun 4 06:14:01 +07 2022 armv7l
Current Time Sat, 04 Jun 2022 05:34:26
Uptime 1 min
GUI over r49049
Reset: no
Issues: upgraded fine
Linksys EA8500...main gateway
DD-WRT v3.0-r49081 std (06/04/22)
Linux 4.9.316 #995 SMP Sat Jun 4 06:34:02 +07 2022 armv7l
GUI install over r49059
all worky very good
#
Netgear WNDR3700 V4
DD-WRT v3.0-r49081 std (06/04/22)
Linux 3.18.140-d6 #144778 Sat Jun 4 12:42:37 +07 2022 mips
scp 'firmware.bin' over over r49059
all good
Router: Netgear R7800
Firmware: DD-WRT v3.0-r49081 std (06/04/22)
Previous: GUI upgrade from DD-WRT v3.0-r48971 std (05/26/22)
Reset: No.
Status: Gateway
Errors: Random reboot after 5 hours, syslog only shows entry after reboot. Previous firmware up from 05/26 8 days no reboots. After it rebooted wifi died and even ethernet cable gave me no access to router. Had to reboot again. Went back to 48971 for now.
LOL I jinxed myself it rebooted on the old firmware as well. Time for a clean setup I think.
Last edited by James Greystone on Sun Jun 05, 2022 15:25; edited 1 time in total
Joined: 14 Sep 2019 Posts: 301 Location: Maine, USA
Posted: Sun Jun 05, 2022 0:55 Post subject:
Router/Version: TP-Link ARCHER-C7 v4
File: tplink_archer-c7-v4.bin
Firmware: DD-WRT v3.0-r49081 std (06/04/22)
Kernel: Linux 3.18.140-d6 #144758 Sat Jun 4 11:56:47 +07 2022 mips
Mode: Gateway/USB/MAC based QOS FQ_CODEL_FAST
Previous: r43516
Reset?: N
Status: Working
Router/Version: TP-Link ARCHER-C7 v4
File: tplink_archer-c7-v4.bin
Firmware: DD-WRT v3.0-r49081 std (06/04/22)
Kernel: Linux 3.18.140-d6 #144758 Sat Jun 4 11:56:47 +07 2022 mips
Mode: AP
Previous: r43516
Reset?: N
Status: Working
Last edited by turbowells on Fri Jun 10, 2022 9:46; edited 1 time in total
Joined: 03 Nov 2015 Posts: 317 Location: Florida, USA
Posted: Sun Jun 05, 2022 1:57 Post subject:
Router:Linksys ea8500 ..WDS AP
Firmware: DD-WRT v3.0-r49081 std (06/04/22)
Kernel: Linux 4.9.316 #995 SMP Sat Jun 4 06:34:02 +07 2022 armv7l
Reset: NO, Gui upgrade from r49049
Errors: None
Router: Linksys ea8500 ..WDS Station
Firmware: DD-WRT v3.0-r49081 std (06/04/22)
Kernel: Linux 4.9.316 #995 SMP Sat Jun 4 06:34:02 +07 2022 armv7l
Reset: NO, Gui upgrade from r49049
Errors: None
Router: TP Link WR1043ND Ver.2 WDS Station
"older build"
Netgear XR500 - Gateway
Firmware Version: DD-WRT v3.0-r49081 std (06/04/22)
Kernel Version: Linux 4.9.316 #997 SMP Sat Jun 4 06:55:18 +07 2022 armv7l
Wireless: Vanilla
Temperatures: CPU 57.137 °C / wlan0 60 °C / wlan1 64 °C
Current Time: Sun, 05 Jun 2022 17:30:57
Uptime: 1 day, 1:10
Reset: No
GUI install over 48971
Installed using Brave browser over wireless
No issues
Thank you BS and thanks you gurus for your guides and wisdom _________________ Netgear XR500 - Gateway
R6700 v3 - Station Bridge
Joined: 15 Aug 2016 Posts: 223 Location: Melbourne, Australia
Posted: Mon Jun 06, 2022 2:43 Post subject: Re: r49081
DD-WRT rocks
Thank you BS & Team.
Netgear R9000
DD-WRT v3.0-r49081 std (06/04/22)
Linux 4.9.316 #632 SMP Sat Jun 4 06:14:01 +07 2022 armv7l
Reset: No
Mode & Uptime: Gateway running over 6hrs
Features:
- Gateway & DNSMasq
- Ethernet, WiFi (Vanilla)
- 5GHz (AC/N-Mixed & vAP via bridge)
- 2.4GHz (NG-Mixed & vAP via bridge)
- Static Leases & DHCP
- CloudFare & WAN DNS ignored
- OpenVPN Client (with separate Killswitch)
- OpenVPN Server disabled
- VLANS (Six separate VLANS, all bridged);
- QoS (HFSC/SFC on MAC, netmask & i/faces priority)
- Port Forwarding to 2nd router
Issues/Errors: Not aware of. _________________ Life is a journey; travel alone makes it less enjoyable and lonely.
Last edited by DWCruiser on Wed Jun 08, 2022 22:33; edited 1 time in total
Joined: 06 Feb 2020 Posts: 167 Location: Maharashtra, India
Posted: Mon Jun 06, 2022 6:53 Post subject:
Router/Version: Netgear R7800
Firmware: DD-WRT v3.0-r49081 std (06/04/22)
Kernel: Linux 4.9.316 #997 SMP Sat Jun 4 06:55:18 +07 2022 armv7l
File/Upload: dd-wrt-webupgrade.bin / Upload using CLI
Mode: Gateway/AP
Reset: No Previous: DD-WRT v3.0-r48996 std (05/30/22)
Setup Using: PPPOE, 2.4 GHz, 5.0 GHz, IPv4, DNSMasq, NTP TimeSync, WireGuard, Samba
Status: Working Fine; running DD-WRT firmware type for 2.4ghz & 5ghz, uptime 2+ Hrs.
one observation, if PPPoE disconnects, after re-connection, internet traffic is not available . I just reboot router and it starts working properly. This is happening since build 48494. Being Non-Linux person. not knowing linux commands I am not able to find which services are not working.
Not ranting about it; as myself not able to help debug it, just for information if someone experiences the same and knows on how to try to trace the root cause.