Posted: Thu Jun 02, 2022 6:55 Post subject: New Build - 06/02/2022 - r49049
Welcome to Atheros r49049 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Thu Jun 02, 2022 8:36 Post subject:
Router Model Netgear Nighthawk X10
Firmware Version DD-WRT v3.0-r49049 std (06/02/22)
Kernel Version Linux 4.9.316 #631 SMP Sat May 28 00:12:24 +07 2022 armv7l
Router Model Netgear R7800
Firmware Version DD-WRT v3.0-r49049 std (06/02/22)
Kernel Version Linux 4.9.316 #992 SMP Thu Jun 2 06:04:09 +07 2022 armv7l
update: CLI
reset: NO
mode: Gateway
status: Operational 3h+
errors: save backup via GUI 404 error, but its working/saving via CLI
nvram backup /opt/R9000-49049.bin
so far no reboots, Im using only 2,4Ghz WiFi on both units.. _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Router/Version: Netgear R7800 File/Kernel: DD-WRT v3.0-r49049 std (06/02/22) / Linux 4.9.316 #992 SMP Thu Jun 2 06:04:09 +07 2022 armv7l Previous/Reset: 05-30-2022-r48996/ No Mode/Status: Working Issues/Errors: is not possible backup options
Linksys EA8500... main gateway
DD-WRT v3.0-r49049 std (06/02/22)
Linux 4.9.316 #988 SMP Wed Jun 1 16:02:58 +07 2022 armv7l
GUI install over r49040
uptime --> 14:46
all good but webif backup NO worky
Joined: 03 Nov 2015 Posts: 317 Location: Florida, USA
Posted: Thu Jun 02, 2022 14:45 Post subject:
Router: Linksys ea8500 ..WDS AP
Firmware: DD-WRT v3.0-r49049 std (06/02/22)
Kernel: Linux 4.9.316 #990 SMP Thu Jun 2 01:15:43 +07 2022 armv7l
Reset: NO, Gui upgrade from r49028
Errors: None yet
Router:Linksys ea8500 ..WDS Station
Firmware: DD-WRT v3.0-r49049 std (06/02/22)
Kernel: Linux 4.9.316 #990 SMP Thu Jun 2 01:15:43 +07 2022 armv7l
Reset: NO, Gui upgrade from r49028
Errors: None yet
Router: TP Link WR1043ND Ver.2 WDS Station
"older build"
Busy day today so it WILL be tested
UPDATE: Wireless on my ea8500 station kept dropping with different WiFi dongles unable to connect at all. Rebooted at least once. Wired connections seem unaffected. Rolled back this station to r48971 and its all working again. Can`t just blame this build just yet as I`m slowly tweeking my settings and my AP seems unaffected with no reboots. Wireless is working there but still painfully slow.
Posted: Fri Jun 03, 2022 3:38 Post subject: R49049
Netgear Nighthawk X10 R9000
Firmware Version DD-WRT v3.0-r49049 std (06/02/22)
Kernel Version Linux 4.9.316 #631 SMP Sat May 28 00:12:24 +07 2022 armv7l
Current Time Thu, 02 Jun 2022 14:36:04
Uptime 6:52
GUI over 48996
reset: no
Issues: good; no sudden reboots
Router just randomly dropped an active connection in a teams meeting. system immediately reconnected. This is a machine listing signal strength as 100% a few feet from router. The logging looks like normal stuff below to me nothing standing out. 6 minutes prior NTP updated
Jun 3 09:38:10 Cisco99533 daemon.info hostapd: wlan0: STA MAC:::: IEEE 802.11: disassociated
Jun 3 09:38:11 Cisco99533 daemon.info hostapd: wlan0: STA Mac::: IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
Jun 3 09:38:16 Cisco99533 daemon.info hostapd: wlan0: STA MAC::: MLME: auth request, signal -41 (Accepted)
Jun 3 09:38:16 Cisco99533 daemon.info hostapd: wlan0: STA MAC::: IEEE 802.11: authenticated
Jun 3 09:38:16 Cisco99533 daemon.info hostapd: wlan0: STA MAC::: MLME: assoc request, signal -41 (Accepted)
Jun 3 09:38:16 Cisco99533 daemon.info hostapd: wlan0: STA MAC::: IEEE 802.11: associated (aid 4)
Jun 3 09:38:16 Cisco99533 daemon.info hostapd: wlan0: STA MAC::: RADIUS: starting accounting session 3065037DF1573BD1
Jun 3 09:38:16 Cisco99533 daemon.info hostapd: wlan0: STA MAC::: WPA: pairwise key handshake completed (RSN)
Jun 3 09:38:16 Cisco99533 daemon.info dnsmasq-dhcp[3784]: DHCPREQUEST(br0)
@the-joker Thanks. Mine is still set to the 1 hr default, seems a bit agressive time in my env only seems to go out of sync only after power events when router runs some time on UPS battery (wish i knew why it caused my computer clocks to run fast).
I'll change it to 4 hrs (14400), which is mmore reasonable