Posted: Thu May 26, 2022 11:53 Post subject: New Build - 05/26/2022 - r48971
Welcome to Atheros r48971 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
TBH When I look up this router it comes up it has a 4MB flash the r48971 is 3.717KB while the r48897 is 3.709KB so both should fit.
If you want to know for sure whats what, flash via CLI, look at the erased block addresses vs the written block addresses and see what the last written block was and see how many blocks were erased after the last writen block of same address to determine how many blocks you have available.
When erasing all the available blocks are erased.
When writing only the needed blocks are written.
Without rebooting: flashing the current r48971 build, copy output to file, then straight after without rebooting flash the build r48897 that works? Copy output to file and check, and grab both output and open a new thread attaching outputs as text files.
I written it that way around so on reboot you have the same r48897, but feel free to flip the order, just remember when you reboot it should apply the last build flashed.
Linksys EA8500...main gateway
DD-WRT v3.0-r48971 std (05/26/22)
Linux 4.9.315 #969 SMP Wed May 25 04:48:27 +07 2022 armv7l
GUI install over r48957
all ok
Uptime 18:53
#
Netgear WNDR3700 V4
DD-WRT v3.0-r48971 std (05/26/22)
Linux 3.18.140-d6 #143586 Thu May 26 08:52:35 +07 2022 mips
scp 'firmware.bin' to /tmp ...over r48957
all worky
Uptime 9:45
---
EDIT ----- just a note...
glad both these units now have:
OpenSSL 1.1.1o
but then again I've had it on me webbyserver for a bit
Server Version: Apache/2.4.53 (Debian) OpenSSL/1.1.1o
Server MPM: prefork
Server Built: 2022-03-15T14:27:39
Posted: Fri May 27, 2022 2:23 Post subject: r48971
Netgear Nighthawk X10 R9000
Firmware Version DD-WRT v3.0-r48971 std (05/26/22)
Kernel Version Linux 4.9.315 #630 SMP Wed May 25 03:48:13 +07 2022 armv7l
Current Time Thu, 26 May 2022 20:14:03
Uptime 2 min
GUI over 48954
Reset: no
Issues: none
GUI upgrade from r48897, all succeed but still on r48897.
CLI same.
My way for CLI:
scp whr*.bin root@192.168.1.1:/tmp
ssh root@192.168.1.1
cd /tmp
mv whr*.bin firmware.bin
Then keep on waiting, it will automatic upgrade.
But still R48897.
My device is Buffalo AIR Station WHR-G300NV2.
On linux PC or Windows PC same result.
At last, firefox v100.x cannot be used to post any content in ddwrt forum.
Router/Version: R7800
File/Kernel: DD-WRT v3.0-r48971 std (05/26/22)
Kernel Version: Linux 4.9.315 #971 SMP Thu May 26 02:12:51 +07 2022 armv7l
Previous/Reset: r48786-GoodBuild / No Reset, CLI Update
Mode/Status: GW / Working Well
Issues/Errors: none / none
Services Used: DHCP WAN,IPv6-6to4,NTP,WG Client,VLANx,BRx,SSH,Syslog,Cron,USB Storage,Entware DNSCrypt v2.1.1
Services Disabled: WiFi,QoS,ttraff,SFE,Telnet,NAS,Samba,YAMon3.4.6
Home Main AP Router
Router/Version: R7800
File/Kernel: DD-WRT v3.0-r48971 std (05/26/22)
Kernel Version: Linux 4.9.315 #971 SMP Thu May 26 02:12:51 +07 2022 armv7l
Previous/Reset: r48786-GoodBuild / No Reset, CLI Update
Mode/Status: GW(double-nat) & AP / Working Well
Issues/Errors: none / none
Services Used: Static WAN,IPv6-6to4,WiFi Vannilla,NTP,2xWG Clients,VAPx,VLANx,BRx,SSH,Syslog,Cron,USB Storage,Entware DNSCrypt v2.1.1
Services Disabled: SPI,QoS,ttraff,SFE,Telnet,NAS,Samba
All running for over 11 hours. Seeing the best WireGuard speeds at 416.8Mbps Download and 293.13Mbps. Bufferbloat Idle at 4ms, Loaded Download at 10ms & Loaded Upload at 12ms. No SFE or QoS.
Thank-you BrianSlyer for your Great Work and everyone else who makes DD-WRT Great on the Forum! _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
GUI upgrade from r48897, all succeed but still on r48897.
CLI same.
My way for CLI:
scp whr*.bin root@192.168.1.1:/tmp
ssh root@192.168.1.1
cd /tmp
mv whr*.bin firmware.bin
Then keep on waiting, it will automatic upgrade.
But still R48897.
My device is Buffalo AIR Station WHR-G300NV2.
On linux PC or Windows PC same result.
At last, firefox v100.x cannot be used to post any content in ddwrt forum.
I use Firefox 100.0.2 (64-bit) and it works for posting here just fine no matter OS.
as for the rest, lovely numbers but no CLI flashing logs documenting anything possibly indicative of what could be it, but since its not size for sure, then a nice question mark shall remain until such time in future that some build may or not fix it.
Joined: 08 May 2018 Posts: 14216 Location: Texas, USA
Posted: Fri May 27, 2022 22:12 Post subject:
It would help to do a manual CLI upgrade to get the information as I don't think that the automatic upgrade logs anything helpful other than pass or fail (?). _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Netgear XR500 - Gateway
Firmware Version: DD-WRT v3.0-r48971 std (05/26/22)
Kernel Version: Linux 4.9.315 #971 SMP Thu May 26 02:12:51 +07 2022 armv7l
Wireless: Vanilla
Temperatures: CPU 57.867 °C / wlan0 60 °C / wlan1 66 °C
Current Time: Fri, 27 May 2022 19:25:43
Uptime: 1 day, 0 min
Reset: No
GUI install over 48865
Installed using Brave browser over wireless
No issues
Thank you BS and thanks you gurus for your guides and wisdom _________________ Netgear XR500 - Gateway
R6700 v3 - Station Bridge
