Posted: Wed May 18, 2022 20:52 Post subject: New Build - 05/18/2022 - r48897
Welcome to Atheros r48897 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Netgear WNDR3700 V4
DD-WRT v3.0-r48897 std (05/18/22)
Linux 3.18.140-d6 #142822 Wed May 18 18:47:27 +07 2022 mips
GUI install over r48891
all good
#
Linksys EA8500...main gateway
DD-WRT v3.0-r48897 std (05/18/22)
Linux 4.9.314 #956 SMP Wed May 18 11:41:44 +07 2022 armv7l
GUI install over r48890
all worky very good
Upgraded from r48886 to r48897 with reset. Using a LAN connection, after firmware loaded it would crash when going to the wireless tab and graphics at the top truncated. Browser says "ERR_CONNECTION_REFUSED". The connection will recover after 20 seconds or so but was not reliable. Reset to defaults again, same issue.
Tried to downgrade to r48786 (with reset) and although it said it completed the firmware update it ended up unresponsive. I think it lost connection again during the flash. I used TFT to recover with r48786 and all is well again.
I had trouble with this build on my R9000. The fix was a firmware reset and then setting the configuration manually. Now, the build works smoothly. You may need to do the same. It can be a long process but you wind up with a clean nvram and a working router. _________________ Netgear R9000
DD-WRT v3.0-r55460 std (03/25/24)
Linux 4.9.337 #715 SMP Mon Mar 25 06:15:53 +07 2024 armv7l
Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
CloudFlare, no SFE, SmartDNS, no QoS
2.4GHz: Vanilla, Airtime Fairness, NG-Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
5GHz: Vanilla, Airtime Fairness, AC/N Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/35Mbps
Posted: Thu May 19, 2022 11:48 Post subject: R48897
Netgear Nighthawk X10 R9000
Firmware Version DD-WRT v3.0-r48897 std (05/18/22)
Kernel Version Linux 4.9.314 #629 SMP Wed May 18 11:26:06 +07 2022 armv7l
Current Time Thu, 19 May 2022 05:42:16
Uptime 1 min
GUI over R48886
Reset: no
Issues: none