Posted: Fri May 06, 2022 6:33 Post subject: New Build - 05/06/2022 - r48810
Welcome to Marvell r48810 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: WRT32x
File/Kernel: Linux 4.9.312 #3193 SMP Fri May 6 02:36:39 +07 2022 armv7l
Previous/Reset: upgrade from r48786 without reset
Mode/Status: AP only
Issues/Errors: so far so good.
Router/Version: WRT1900acs
Kernel: Linux 4.9.312 #3193 SMP Fri May 6 02:36:39 +07 2022 armv7l
Previous/Reset: upgrade from r48786 without reset via CUI
Mode/Status: AP with unbound
Issues/Errors: Work stable, no error found.
- update works good without any problems
- VPN WireGuard
- USB
- DDNS
- CRON "delete directories older > x Days, created by 3xWebCams (stored on128GB SSD)"
- Port Forwarding
- FTP
- Samba
- WLAN offline, I use UniFi AP AC LITE as access Point!
- Lan
all OK without error, Thank You for the good work !!!!
Router/Version: Linksys WRT1900ACSv2
File/Kernel: Linux 4.9.312 #3193 SMP Fri May 6 02:36:39 +07 2022 armv7l
Previous/Reset: 04-26-2022-r48741 upgrade after reset
Mode/Status: AP only
Issues/Errors: In Setup -->Switch config page, i have plugged the ethernet cable to Lan port 1 but the page shown port 1 is down and port 4 connected at 1000 which is not correct. Lan port 3 is connected but Port 2 is green.I confirmed WRT32x also has the same problem.
The other problem is that the time cannot sync if i set NTP server 223.255.185.2 and time zone is asia/Hong_Kong. Same network config and NTP setting on wrt32x without any time sync problem.
Joined: 08 May 2018 Posts: 14244 Location: Texas, USA
Posted: Wed May 11, 2022 0:45 Post subject:
@raywan: Physical ports on the router switch and ports on the webUI are reveresed; known cosmetic issue. On your wired AP, if the gateway (IP address of the upstream router) is not supplied, NTP will not sync. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
@raywan: Physical ports on the router switch and ports on the webUI are reveresed; known cosmetic issue. On your wired AP, if the gateway (IP address of the upstream router) is not supplied, NTP will not sync.
Both Gateway and DNS IP are assigned correctly.Wrt1900acsv2 is able to ping 1.1.1.1 in Diagnostic page. All the wireless clients are able to access internet but wrt1900acsv2 seems cannot sync NTP server. The same network IP config was applied to wrt32x. It doesn't have the NTP sync problem.
Posted: Fri May 13, 2022 4:14 Post subject: upgrade
upgrade WRT3200ACM from 47822 to 48810 did not factory default
no issues
DHCP static leases 15+
openvpn
VWLANx3
SNMP - to cacti server local and remote
apple devices seem to work same previous build which as been on going issue for some time.
guest filtering on VWAN works
syslog