R48607 Problem

Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Author Message
audioquest
DD-WRT Novice


Joined: 31 May 2017
Posts: 36

PostPosted: Sat Apr 09, 2022 21:22    Post subject: R48607 Problem Reply with quote
WRT1900ACSV2

I performed a firmware upgrade from 44048 to 48607 completed successfully
The default gateway is 0.0.0.0

I am unable to change the IP Address and default gateway successfully.

Does anyone know of a change in the firmware setting that I need to make for the change to take effect.

Thanks in advance


Last edited by audioquest on Sun Apr 10, 2022 0:05; edited 2 times in total
Sponsor
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 13112
Location: Texas, USA

PostPosted: Sat Apr 09, 2022 22:59    Post subject: Reply with quote
You probably need to upgrade via CLI as the version you have may be broken for webflash upgrades. See installation wiki link in my signature and:

Sticky: DD-WRT Installation, Upgrade & Basic Setup–Cliff Notes

_________________
"Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT
Pogo - A minimal level of ability is expected and needed...
At some point, people just get plain tired of this place.
Because they are tired of bottom-feeders and the same old hat.

----------------------
Linux User #377467 counter.li.org / linuxcounter.net
the-joker
DD-WRT Developer/Maintainer


Joined: 31 Jul 2021
Posts: 2143
Location: All over YOUR webs

PostPosted: Sun Apr 10, 2022 8:43    Post subject: Reply with quote
That was a large build version jump, nvram reset or router reset is recommended here.

My updated rule of thumb;

If the current installed build is equal or older than max 6 months vs the build you are upgrading to, then nvram reset is recommended followed by reconfiguration.

Always upgrade to the very latest public build of DD-WRT, unless you know by following DD-WRT development some issues are likely to cause problems with current setup.

Minimum DD-WRT upgrade interval is monthly, unless exigent circumstances due to security patches and 3rd party libraries upgrades, kernels, etc, etc...

Maximum time to push my luck without nvram reset 1 year.

_________________
Saving your retinas from the burn!🔥
DD-WRT Inspired themes for routers
DD-WRT Inspired themes for the phpBB Forum
DD-WRT Inspired themes for the SVN Trac & FTP site
Join in for a chat @ #style_it_themes_public:matrix.org or #style_it_themes:discord

DD-WRT UI Themes Bug Reporting and Discussion thread

Router: ANus RT-AC68U E1 (recognized as C1)
blkt
DD-WRT Guru


Joined: 20 Jan 2019
Posts: 4585

PostPosted: Sun Apr 10, 2022 15:02    Post subject: Reply with quote
New Build - 08/10/2022 - r49677 reports look good stay with current builds and especially for security fixes.
At this point no one should use old builds Marvell has been good since r47720 or early December, 4 months.

r44048 config is too old GUI factory defaults, reset button 10 seconds or Telnet root nvram erase && reboot.
Give the router some time to reboot and stabilize if no WAN power cycle unspecified ISP modem equipment.
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum