Posted: Wed Mar 23, 2022 6:15 Post subject: New Build - 03/23/2022 - r48567
Welcome to MediaTek r48567 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
After selecting "Services", the save password message dialog will appear. This always happens.
User Name: 8000 or 1813
Password: "numbers/letters" (always the same)
Message appears frequently when choosing options within Services.
Message appears once when leaving Services to other options (Setup, Security, Access Restrictions, etc.) If other options are chosen after leaving Services, save password dialog does NOT appear.
Password is usually "numbers/letters", but seems to temporarily save the last entered password, i.e. router password
Password changes back to "numbers/letters" when leaving Services. Will no longer show router password.
Offers to save other passwords as well.
Only occurs on Firefox.
My configuration has no passwords saved in Firefox at all.
Does NOT happen if Services was not entered.
"numbers/letters" are always the same. I don't know where this came from.
Router Model displays as NetgearR6800.
R6700V2 and R6800 has the same chip.
No other problems. Internet speed significantly better than prior build. Connection to router significantly better as well.
Router - D-Link 810L b1
Firmware - DD-WRT v3.0-r48362 std
Issue - wireguard access and wrong router issue (c1 and not b1)
Client mode on 2.4ghz with 5ghz AP. Connected lan to bridge enabled modem/router.
I have not been able to access or enable wireguard configuration since wireguard was implemented. Is some routers not wireguard configured? I can see in syslog that wireguard is used as a tunnel. Tried following several guides but none are mentioning manually inställning wireguard or GUI issue.
Also my firmware shows c1 instead of b1 router model of 810L. Have been that since years ago. Might be common.
Joined: 18 Mar 2014 Posts: 12836 Location: Netherlands
Posted: Thu Mar 24, 2022 12:34 Post subject:
willexmen wrote:
Router - D-Link 810L b1
Firmware - DD-WRT v3.0-r48362 std
Issue - wireguard access and wrong router issue (c1 and not b1)
Client mode on 2.4ghz with 5ghz AP. Connected lan to bridge enabled modem/router.
I have not been able to access or enable wireguard configuration since wireguard was implemented. Is some routers not wireguard configured? I can see in syslog that wireguard is used as a tunnel. Tried following several guides but none are mentioning manually inställning wireguard or GUI issue.
Also my firmware shows c1 instead of b1 router model of 810L. Have been that since years ago. Might be common.
Which kernel is reported?
It looks like the router has 8MB Flash 64 MB Ram so WireGuard might be possible if it is using Kernel 3.10 or above.
The build size is somewhat over 5 MB but maybe there is a limitation to go higher.
If the Kernel version is OK I will ping the developer.