Posted: Sun Mar 20, 2022 9:33 Post subject: New Build - 03/20/2022 - r48540
Welcome to Marvell r48540 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
I want to report a layout error in the web interface after installing a USB stick
this problem seems to occur when opt is not formatted ! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Posted: Mon Mar 21, 2022 3:27 Post subject: Switch config tab
Router/Version: WRT1200AC
File/Kernel: Linux 4.9.307 #3141 SMP Sun Mar 20 03:06:24 +07 2022 armv
Previous/Reset: 48494
Mode/Status: A/P operational
Issues/Errors:
So I don't know if this is a hardware issue if this has been reported before, or I am just lucky. On the back of the router, ports are labeled [Internet] [1] - [4]. Same as in the gui.
However, it seems to be reporting in reverse order. While the Ethernet cable is physically plugged into port 1, the gui is reporting port 4. I only have one cable going from the router to a switch.
Joined: 04 Aug 2018 Posts: 1447 Location: Appalachian mountains, USA
Posted: Mon Mar 21, 2022 15:55 Post subject: Re: Switch config tab
sapphireweb wrote:
On the back of the router, ports are labeled [Internet] [1] - [4]. Same as in the gui.
However, it seems to be reporting in reverse order. While the Ethernet cable is physically plugged into port 1, the gui is reporting port 4.
It's well known that the WRT series has ports labeled 1..4 on the back panel but denotes them as 3..0 internally in the switch configuration. (Explored at the VLAN link in my sig.) _________________ 2x Netgear XR500 and 3x Linksys WRT1900ACSv2 on 53544: VLANs, VAPs, NAS, station mode, OpenVPN client (AirVPN), wireguard server (AirVPN port forward) and clients (AzireVPN, AirVPN, private), 3 DNSCrypt providers via VPN.
Posted: Mon Mar 21, 2022 19:20 Post subject: Re: Switch config tab
Quote:
It's well known that the WRT series has ports labeled 1..4 on the back panel but denotes them as 3..0 internally in the switch configuration. (Explored at the VLAN link in my sig.)
After looking at the link, I am assuming that I will be ok, if I just leave it alone, and remember that 4 is 1, 1 is 4 & 2 is 2. Or am I going to run into issues?
I want to report a layout error in the web interface after installing a USB stick
this problem seems to occur when opt is not formatted !
I have two WRT3200ACM and one WT1900AC with USB storage devices, and all of them display the storage bar correctly. Must be related to the storage device. _________________ Linksys: Several WRTxx00AC variations | Netgear: 4x WNDR4500v2, 7x WNDR4300, R6400v1 | Asus: 2x RT-AC66U | Gl.inet: 3x GL-AR150
Joined: 04 Aug 2018 Posts: 1447 Location: Appalachian mountains, USA
Posted: Thu Mar 24, 2022 15:37 Post subject: Re: Switch config tab
sapphireweb wrote:
Quote:
It's well known that the WRT series has ports labeled 1..4 on the back panel but denotes them as 3..0 internally in the switch configuration. (Explored at the VLAN link in my sig.)
After looking at the link, I am assuming that I will be ok, if I just leave it alone, and remember that 4 is 1, 1 is 4 & 2 is 2. Or am I going to run into issues?
I hate that this is in the new-build thread, where it most clearly does not belong, but let's leave things clear.
But port 4 on the back is 0 internally, not 1. Port 3 is 1 internally, etc. _________________ 2x Netgear XR500 and 3x Linksys WRT1900ACSv2 on 53544: VLANs, VAPs, NAS, station mode, OpenVPN client (AirVPN), wireguard server (AirVPN port forward) and clients (AzireVPN, AirVPN, private), 3 DNSCrypt providers via VPN.
