Posted: Fri Jan 28, 2022 4:29 Post subject: New Build - 01/28/2022 - r48218
Welcome to Atheros r48218 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs. Logs: 'dmesg' 'cat /tmp/var/log/messages' syslog klog, serial, strace, tcpdump, wireshark.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Gremlins: reset & configure manually, not restore a backup. Reboot. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 16 Nov 2015 Posts: 6440 Location: UK, London, just across the river..
Posted: Fri Jan 28, 2022 9:25 Post subject:
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r48218 std (01/28/22)
Kernel Version Linux 3.18.140-d6 #135228 Fri Jan 28 05:47:42 +07 2022 mips
Thanks BS for adding the DNSSEC trust-anchor, however if GUI option validate DNSSEC is used no DNS no internet, but i don't need to use it anyway...as im trying to make stubby to work with DNSSEC instead...will post results later, of what i was trying, so far with self added trust-anchor at /opt was not working..lets see if it will work now...(i doubt ) but thanks anyway... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Linksys EA8500...main gateway
DD-WRT v3.0-r48218 std (01/28/22)
Linux 4.9.298 #721 SMP Thu Jan 27 18:14:17 +07 2022 armv7l
GUI install over r48028
after 3 hrs would NOT resolve sites --- the recursive DNS resolver showed over 4000 active IP connections but none working.
Local DNS was still good. I disabled 'unbound'
Have two Verisign DNS servers set & one OpenNic ...they do DNSSEC anyways
rebooted after change DNS --- uptime 9:47 ...all is very good
Joined: 16 Nov 2015 Posts: 6440 Location: UK, London, just across the river..
Posted: Fri Jan 28, 2022 11:21 Post subject: Re: TP-LINK WR841N WiFi Power
m3lab wrote:
Router/Version: TP-LINK WR841N Previous/Reset: r48081 -> r48138 -> r48218 Mode/Status: AP/ Ok Issues: WiFi TX power is 16dBm
Buongiorno,
I live in Italy and as far as I know the max Tx power could be 20dBm but here is limited to 16dBm: is this an error?
Is/are there hint(s), tip(s) to reach max power?
Thanks in advance,
.m.
Different country regions have different regulations regarding Channels dBm MAX power...try to change your country domain to Canada or Haiti...(I always use Channel 11 too) and check again...
your router max power is 20dBm so it wont go more than that... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Netgear WNDR3700 V4
DD-WRT v3.0-r48218 std (01/28/22)
Linux 3.18.140-d6 #135256 Fri Jan 28 06:42:55 +07 2022 mips
switch / ovpn server
all ok --- uptime 1:47
---
NOTE: my previous post about 'unbound' quit working ---
That is NOT necessarily a DD-WRT problem ...most likely not..could have been several things...
...lots of bad crazies still roam this world
Update method: SSH / CLI
Router/Version: Netgear R9000 Nighthawk X10
File/Kernel: DD-WRT v3.0-r48218 std (01/28/22)
Previous/Reset: DD-WRT v3.0-r48208 std (01/26/22) / No
Mode/Status: Gateway / Working Normally
Issues/Errors: Although the build did load the leases file on reboot, and the Use JFFS2 for client lease DB option was checked, I had to click Apply on the page to get the dnsmasq.leases file to start updating on /jffs. Also, the Active Clients table on the Status, LAN tab had many Hostnames as * until I erased /tmp/dnsmasq.leases. _________________ Netgear R9000
DD-WRT v3.0-r55819 std (04/17/24)
Linux 4.9.337 #722 SMP Wed Apr 17 04:16:49 +07 2024 armv7l
Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
CloudFlare, no SFE, SmartDNS, no QoS
2.4GHz: Vanilla, Airtime Fairness, NG-Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
5GHz: Vanilla, Airtime Fairness, AC/N Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/35Mbps
Router Model: Netgear Nighthawk X10 P9000
Firmware Version: DD-WRT v3.0-r48218 std (01/28/22)
Kernel Version: Linux 4.9.298 #609 SMP Thu Jan 27 21:02:15 +07 2022 armv7l
Previous/Reset: r48141, Web update w/o reset
Mode/Status: AP, Gateway / Working
Setup/Using: Vanilla 2.4,DD-WRT, 5GHz, vlan, OpenVPN w/PBR, DDNS, DNSmasq, 2xUSB+Samba
Uptime 1 hr
Minor Issues: After boot, USBs were dirty (not umounted during upgrade?) ...and...
Quote:
Previously unseen log warnings
Dec 31 16:00:48 user.info : [openvpn] : General Killswitch for OpenVPN enabled from OpenVPN
Dec 31 16:00:48 daemon.warn openvpn[2222]: WARNING: Using --management on a TCP port WITHOUT passwords is STRONGLY discouraged and considered insecure
Dec 31 16:00:48 daemon.warn openvpn[2222]: WARNING: Using --management on a TCP port WITHOUT passwords is STRONGLY discouraged and considered insecure
Dec 31 16:00:48 daemon.warn openvpn[2222]: WARNING: Using --management on a TCP port WITHOUT passwords is STRONGLY discouraged and considered insecure
Dec 31 16:00:48 daemon.warn openvpn[2222]: WARNING: Using --management on a TCP port WITHOUT passwords is STRONGLY discouraged and considered insecure
Dec 31 16:00:48 daemon.warn openvpn[2222]: WARNING: Using --management on a TCP port WITHOUT passwords is STRONGLY discouraged and considered insecure
Dec 31 16:00:48 daemon.warn openvpn[2222]: WARNING: file '/tmp/openvpncl/credentials' is group or others accessible
Posted: Fri Jan 28, 2022 18:59 Post subject: Re: TP-LINK WR841N WiFi Power
Alozaros wrote:
Different country regions have different regulations regarding Channels dBm MAX power...try to change your country domain to Canada or Haiti...(I always use Channel 11 too) and check again...
your router max power is 20dBm so it wont go more than that...
Thanks: yesterday, I've used Canada and dBm max was 18... Following your suggestion (Haiti) it is still 16 dBm ...
Joined: 16 Nov 2015 Posts: 6440 Location: UK, London, just across the river..
Posted: Fri Jan 28, 2022 20:09 Post subject: Re: TP-LINK WR841N WiFi Power
m3lab wrote:
Alozaros wrote:
Different country regions have different regulations regarding Channels dBm MAX power...try to change your country domain to Canada or Haiti...(I always use Channel 11 too) and check again...
your router max power is 20dBm so it wont go more than that...
Thanks: yesterday, I've used Canada and dBm max was 18... Following your suggestion (Haiti) it is still 16 dBm ...
.m.
that is the hardware max of your unit i guess...
some units have more powerful amps... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Fri Jan 28, 2022 20:17 Post subject: Re: TP-LINK WR841N WiFi Power
Alozaros wrote:
that is the hardware max of your unit i guess...
some units have more powerful amps...
not always the amps sometimes many times its just stupid eeprom etc limits cause of idiot companies limiting their own products' potential just cause.. _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers