Posted: Mon Jan 10, 2022 6:42 Post subject: New Build - 01/10/2022 - r48075
Welcome to Broadcom r48075 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• DNScrypt 1.95 can still be used in WebUIbut v2 (not compatible) requires Golang and thus Entware. See Trac ticket #6246.
• WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Try client or repeater modes, but YMMV.
• VAPs not working at bootare fixed, both unbridged (r40634) and bridged (r47822). Please test, removestartup commands.
• If startup scripts do not work from USB add delay (wait script), sleep 25 or try Administration -> Commands -> Save USB.
• Broadcom ARM devices if 5 GHz channels are missingvia Telnet/SSH: 'nvram set brcm_unlock=1' 'nvram commit' 'reboot'.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs. Logs: 'dmesg' 'cat /tmp/var/log/messages' syslog klog, serial, strace, tcpdump, wireshark.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Gremlins: reset & configure manually, not restore a backup. Reboot. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Router Model: Netgear R7000
Firmware Version: netgear-r7000-webflash.bin
Kernel Version: Linux 4.4.298 #4930 SMP Sun Jan 9 02:42:01 +07 2022 armv7l
Reset: no
Operating Mode/Setup: Gateway / AP
Status: Works well in general but smartdns does not read custom configuration from /jffs/etc now. Worked fine up until build 47976. Samba does not work, no access from MacOs at least. Haven't tried Samba access in a while, works on 47618 but not on 47976 and forward.
Also log contains this, new, message:
Code:
Guardian1 user.err : [flash] : Could not unlock MTD device: ddwrt
_________________ Netgear R7000 on Build 55109
Asus AC-AC68U rev. C1 (AP) on Build 55109
Asus AC-68U rev. A1 on Build 54604
Asus AC-68U rev. A1 on Build 53339
Joined: 01 Dec 2021 Posts: 289 Location: Maryland, United States
Posted: Mon Jan 10, 2022 20:04 Post subject:
[b]Router/Version:[/b] Netgear R6300v1
[b]Firmware:[/b] DD-WRT v3.0-r48075 giga (01/10/22)
[b]File/Kernel:[/b] Linux 4.4.298 #13598 Mon Jan 10 04:49:50 +07 2022 mips
[b]Previous/Reset:[/b] r48068 No reset
[b]Mode/Status:[/b] Router / Working
[b]Issues/Errors:[/b] Several
Initially the update worked without any problems. I decided to try different wireless channels and I did apply settings after each try. After about five changes when I did apply setting I lost access to the router page (internet still worked). The only way I could regain access was by power cycling the router. The problem did not go away and if I pressed apply setting once I would have the same problem. I did a 30-30-30 reset and event though that was successful I could not restore my setting or use apply setting (same problem). I tried a 30-30-30 reset again but that did not help. I finally was able to restore the Netgear original firmware and then put back the DD-WRT firmware. After that I was able to to a restore without any problems.
I believe this problem started about three or four revisions before but I thought it was fixed. It appears the apply updates writes to an area that does not get flushed with subsequent update or a 30-30-30 reset.
The IPv6 issue has been posted in another post on this thread. The router cannot get a WAN IPv6 address
Router/Version: Netgear R6250
Firmware: DD-WRT v3.0-r48075 std (01/10/22)
Kernel: Linux 4.4.298 #4934 SMP Mon Jan 10 03:49:09 +07 2022 armv7l
Mode: Gateway, Wireless AP, unbound, CTF & FA Enabled. NAT/QoS Off
Reset: No
Previous : DD-WRT v3.0-r48068 std (01/09/22)
Upgrade: CUI
Temperatures CPU 78.6 °C / WL0 50.3 schedule start/stop /WL1 56.5 schedule start/stop
Load: 0.08, 0.12, 0.07
Uptime 6 hour
Works
But verified two times that unbound starts default from /tmp/unbound.conf instead of my internal /jffs/etc/unbound.conf while cold-boot or reboot ONLY in R48075.
Joined: 26 Mar 2013 Posts: 1857 Location: Hung Hom, Hong Kong
Posted: Tue Jan 11, 2022 10:53 Post subject:
saphirely wrote:
But verified two times that unbound starts default from /tmp/unbound.conf instead of my internal /jffs/etc/unbound.conf while cold-boot or reboot ONLY in R48075.
....
Only way is manual stopservice unbound then startservice unbound, that is
....
Same problem in build 47822!! I thought maybe it's just me, so I didn't report it.
Furthermore, minidlna sometimes wasn't started.
The NAS init script really should have checked whether its child services were all started properly.
_________________ Router: Asus RT-N18U (rev. A1)
Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!
