Posted: Sun Jan 09, 2022 8:47 Post subject: New Build - 01/09/2022 - r48068
Welcome to Atheros r48068 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs. Logs: 'dmesg' 'cat /tmp/var/log/messages' syslog klog, serial, strace, tcpdump, wireshark.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Gremlins: reset & configure manually, not restore a backup. Reboot. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Linksys EA8500...main gateway
DD-WRT v3.0-r48068 std (01/09/22)
Linux 4.9.296 #655 SMP Sat Jan 8 15:06:22 +07 2022 armv7l
GUI install over r47492
worky ok -- Uptime 12:45
also installed on EA8500 switch / ovpn server / samba share
samba shares are ok now using Debian OS, HOWEVER:
if try to replace file on shared drive it gives 'invalid argument'
worky ok if delete file or directory from shared drive & then copy to it
another NOTE: moto edge+ phone
Cx File Explorer still will NOT connect
x-plore file manager will worky but is slow as hell ---
if moving 100MB or bigger it is faster to boot back into r47942 & use Cx File Explorer
#
Netgear WNDR3700 V4
DD-WRT v3.0-r48068 std (01/09/22)
Linux 3.18.140-d6 #133664 Sun Jan 9 05:56:05 +07 2022 mips
GUI install over r47985
switch / ovpn server
all good --- Uptime 9:50
Joined: 21 Jul 2006 Posts: 1898 Location: Fortaleza Ce Brazil
Posted: Sun Jan 09, 2022 12:27 Post subject:
[quote="mrjcd"]Linksys EA8500...main gateway
DD-WRT v3.0-r48068 std (01/09/22)
Linux 4.9.296 #655 SMP Sat Jan 8 15:06:22 +07 2022 armv7l
GUI install over r47492
worky ok -- Uptime 12:45
also installed on EA8500 switch / ovpn server / samba share
samba shares are ok now using Debian OS, HOWEVER:
if try to replace file on shared drive it gives 'invalid argument'
worky ok if delete file or directory from shared drive & then copy to it
another NOTE: moto edge+ phone
Cx File Explorer still will NOT connect
x-plore file manager will worky but is slow as hell ---
if moving 100MB or bigger it is faster to boot back into r47942 & use Cx File Explorer
#
We have a similar specs ... same issues here with r7800 _________________ DDwrt ...it rocks ....
1 R7800 54420 AP Wireguard webserver JFFS SAMBA FTP usb HD Mesh
1 R7800 54420 Cli Mesh
1 WZR1750 54389 AP Webserver Samba Wireguard
1 TP link Archer C7v5 54420 Cli Mesh
1 DD x86_64 48296 Gateway Samba Ftp Webserver
Update method: SSH / CLI
Router/Version: Netgear R9000 Nighthawk X10
File/Kernel: DD-WRT v3.0-r48068 std (01/09/22)
Previous/Reset: DD-WRT v3.0-r47976 std (01/06/22) / No
Mode/Status: Gateway / Working Normally
Issues/Errors: Although the build did load the leases file on reboot, and the Use JFFS2 for client lease DB option was checked, I had to click Apply on the page to get the dnsmasq.leases file to start updating on /jffs. Also, the Active Clients table on the Status, LAN tab had many Hostnames as * until I erased /tmp/dnsmasq.leases.
I like the new Static Leases column and button. Great addition! _________________ Netgear R9000
DD-WRT v3.0-r55819 std (04/17/24)
Linux 4.9.337 #722 SMP Wed Apr 17 04:16:49 +07 2024 armv7l
Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
CloudFlare, no SFE, SmartDNS, no QoS
2.4GHz: Vanilla, Airtime Fairness, NG-Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
5GHz: Vanilla, Airtime Fairness, AC/N Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/35Mbps
Router Model TP-Link TL-WR841ND v11
Firmware Version DD-WRT v3.0-r48068 std (01/09/22)
Kernel Version Linux 3.18.140-d6 #133622 Sun Jan 9 04:47:37 +07 2022 mips
Update via CLI from r47976
Reset: Yes
Working as AP, Mixed, HT40.
Issue: After resetting to factory UPnP cannot be set to enabled, on that page neither Save or Apply button work, at page refresh UPnP is displayed as disabled.
Later edit: I reverted to r47976, enabled UPnP and updated again to r48068. UPnP is still displayed as enabled after update. But now cannot be set to disabled, Save and Apply buttons don't work.
samba shares are ok now using Debian OS, HOWEVER:
if try to replace file on shared drive it gives 'invalid argument'
worky ok if delete file or directory from shared drive & then copy to it
another NOTE: moto edge+ phone
Cx File Explorer still will NOT connect
x-plore file manager will worky but is slow as hell ---
if moving 100MB or bigger it is faster to boot back into r47942 & use Cx File Explorer
can confirm EA8500 r48075
samba will overwrite files on the share drives without a problem.
thank you, BS
silly Cx File Explorer still cannot connect to shares but that ain't no biggy cause I still have the oldass WRT160NL running r42132 with a 16GB FAT flash drive samba share it can get at easily.