Posted: Thu Jan 06, 2022 8:15 Post subject: New Build - 01/06/2022 - r47976
Welcome to Broadcom r47976 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• DNScrypt 1.95 can still be used in WebUIbut v2 (not compatible) requires Golang and thus Entware. See Trac ticket #6246.
• WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Try client or repeater modes, but YMMV.
• VAPs not working at bootare fixed, both unbridged (r40634) and bridged (r47822). Please test, removestartup commands.
• If startup scripts do not work from USB add delay (wait script), sleep 25 or try Administration -> Commands -> Save USB.
• Broadcom ARM devices if 5 GHz channels are missingvia Telnet/SSH: 'nvram set brcm_unlock=1' 'nvram commit' 'reboot'.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg' 'cat /tmp/var/log/messages', syslog klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Gremlins: reset & configure manually, not restore a backup. Reboot. Search Trac & discuss in forum before opening tickets.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Linksys E2500
DD-WRT v3.0-r47976 mega (01/06/22)
Linux 4.4.297 #13424 Thu Jan 6 05:05:04 +07 2022 mips
'dd-wrt.v24-47976_NEWD-2_K3.x_mega.bin'
GUI install over r47961
used as a simple WAP
all good -- up 6:01
Router/Version: Netgear R7000 / DD-WRT v3.0-r47976 std
File/Kernel: Linux 4.4.297 #4858 SMP armv7l
Previous/Reset: 12-30-2021-r47942 / Yes
Mode/Status: WAP with 2X bridged VAPs (wl0.1,wl1.1),operating mode router / wan,sfe,dhcp,dnsmasq,security all disabled
Issues/Errors:
No errors, I can confirm that the "disable GUI wireless access" issue that was reported in a previous forum post has been resolved, the below nvram output was gathered after performing factory reset via the WebUI, and reconfiguring from scratch:
Firmware: v3.0-r47976 std (06/01/22)
Router/Version: Netgear R7000
Kernel: Linux 4.4.297 #4858 SMP Thu Jan 6 03:47:18 +07 2022 armv7l
Previous: v3.0-r44772 std (11/11/20)
Mode/Status: AP wired and wireless
Reset: no
Temperatures: CPU 59.1 °C / WL0 48.3 °C / WL1 51.0 °C
Issues/Errors: No _________________ Netgear R7000 :
#1 - DD-WRT v3.0-r50551 std (10/19/22) - running since 11/28/22 - DHCP Off / IPv4 only / VAP Off & Wifi 2.4 / 5Ghz #2 - DD-WRT v3.0-r50551 std (10/19/22) - running since 11/28/22 - DHCP On / IPv4 & IPv6 / VAP On & Wifi 2.4 / 5Ghz & Isolated Guest Network
Joined: 18 Mar 2014 Posts: 12882 Location: Netherlands
Posted: Thu Jan 06, 2022 16:33 Post subject:
Router Model: Linksys EA6900 (XVortex CFE)
Firmware Version: DD-WRT v3.0-r47976M Community Build (01/06/22)
Kernel Version: Linux 4.4.298 #1 SMP Thu Jan 6 15:51:20 CET 2022 armv7l
Upgraded: DD-WRT v3.0-r47925M Community Build (12/29/21) via telnet (update via GUI not possible because nvram is placed on linux partition and not linux2 partition due to Xvortex CFE)
Reset: No, not this time
Configuration: AP, DHCP server, 2,4GHz wireless running with VAP running, 5GHz running, some static leases and some port range forwarding, WireGuard client with PBR to Keepsolid, OpenVPN client with PBR
USB (only USB 2 port working with this Xvortex build) and Samba working (with extra patches so YMMMV )
NVRAM size 44K (NVRAM size should not be a problem with the Xvortex CFE)
Router/Version: Netgear R6250
Firmware: DD-WRT v3.0-r47976 std (01/06/22)
Kernel: Linux 4.4.297 #4858 SMP Thu Jan 6 03:47:18 +07 2022 armv7l
Mode: Gateway, Wireless AP, dnscrypt instead of unbound, CTF & FA Enabled. NAT/QoS Off
Reset: No
Previous : DD-WRT v3.0-r47942 std (12/30/21)
Upgrade: Web
Temperatures CPU 80.2 °C / WL0 50.3 schedule start/stop /WL1 57.2 schedule start/stop
Load: 0.00, 0.01, 0.00
Uptime 1 hour
Works.
But there is new error I displayed here.
After flashing, WAN DNS is NOT ignored even it is ignored.
I try to change WAN Connection Type DHCP to Fixed IP, reboot...Return to DHCP, reboot, now WAN DNS is Ignored indeed.
The above error has never happened previously. I used https://www.dnsleaktest.com to verify.
Router/Version: Asus rt-n16
Firmware: DD-WRT v3.0-r47976 big (01/06/22)
Kernel: Linux rt-n16 4.4.297 #13420 Thu Jan 6 04:59:15 +07 2022 mips DD-WRT
Mode: Gateway (USB dongle), no wlan
Reset: No
Previous : big release from 2019
Upgrade: web
Temperatures: not available
Router/Version: Netgear R7000
File: netgear-r7000-webflash.bin
Firmware: DD-WRT v3.0-r47976 std (01/06/22) (prev. DD-WRT v3.0-r47911 std (12/23/21))
Kernel: Linux 4.4.297 #4858 SMP Thu Jan 6 03:47:18 +07 2022 armv7l
Mode: Gateway, SFE disabled, Wifi disabled, Wireguard for external access, WAN to DSL, Keep Alive reboot 5:00 in the morning, samba to access external (ext4) disk
Reset: No
Status: 1d up, drive is mounted and accessible for router, but smb at ubuntu / android / windows gets access denied after inserting username & password for network share.
This used to work before, settings unchanged since many releases.
Router/Version: Asus RT-N66U
File: dd-wrt.v24-47976_NEWD-2_K3.x-big-RT-N66U.trx
Firmware: DD-WRT v3.0-r47976 big (01/06/22) (prev. DD-WRT v3.0-r47911 big (12/23/21))
Kernel: Linux 4.4.297 #13420 Thu Jan 6 04:59:15 +07 2022 mips
Mode: Gateway, SFE disabled, Wifi disabled, WAN disabled, Wireguard Endpoint for external VPS, connected via LAN to R7800, Keep Alive reboot 6:05 in the morning
Reset: No
Status: 1d up, Ok.
[quote="Zyxx"]Router/Version: Netgear R7000
File: netgear-r7000-webflash.bin
Firmware: DD-WRT v3.0-r47976 std (01/06/22) (prev. DD-WRT v3.0-r47911 std (12/23/21))
Kernel: Linux 4.4.297 #4858 SMP Thu Jan 6 03:47:18 +07 2022 armv7l
Mode: Gateway, SFE disabled, Wifi disabled, Wireguard for external access, WAN to DSL, Keep Alive reboot 5:00 in the morning, samba to access external (ext4) disk
Reset: No
Status: 1d up, drive is mounted and accessible for router, but smb at ubuntu / android / windows gets access denied after inserting username & password for network share.
This used to work before, settings unchanged since many releases.
Same Router and almost same configuration and the same Samba problem.
This is really annoying, after every update there is a samba problem