Firmware: v3.0-r47745 std (12/04/21)
Router/Version: Netgear R7000 Kernel: Linux 4.4.293 #4545 SMP Fri Dec 3 17:22:02 +07 2021 armv7l
Previous: v3.0-r47720 std (12/02/21)
Mode/Status: AP wired and wireless / Up and running for 22 hours
Reset: Soft boot before and after upgrade
Temperatures: CPU 56.9 °C / WL0 45.0 °C / WL1 50.0 °C
Issues/Errors: Nothing significant
Updated via webif. No 'nvram erase' this time, last one was in July 2018 (r36325).
Upload and Download speeds are to ISP spec (500/500 Mbps). Nothing unexpected in the syslog.
Current basic R7000 setup (subject to change of course):
- Static WAN IP
- Shortcut Forwarding Engine: CTF, Flow Acceleration: Disabled
- STP - Enabled
- IPv4 only, both WAN and LAN
- LAN DHCP Enabled
- Not currently forwarding any ports
- Wireless: AP, Regulatory Domain = CANADA, wl0 Mixed (ch. 6), wl1 AC/N-Mixed (ch. 36, VHT80), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- No custom scripts
- No: ttraf, Tor, VNC, Zabbix, VPN, Radius, OpenVPN
- No: UPnP, DMZ, QoS
- No: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7
Firmware: DD-WRT v3.0-r47745 micro (12/04/21)
Router/Version: Linksys WRT54Gv8
File/Kernel: Linux 2.4.37 #67291 Sat Dec 4 05:33:17 +07 2021 mips
Previous/Reset: r47720 No reset,hard reboot after flash
Mode/Status: CLient Bridge only
Issues/Errors: None
Firmware: DD-WRT v3.0-r47745 micro (12/04/21)
Router/Version: Linksys WRT54Gv6
File/Kernel: Linux 2.4.37 #67291 Sat Dec 4 05:33:17 +07 2021 mips
Previous/Reset: r47720, No reset,hard reboot after flash
Mode/Status: WAP/Switch
Issues/Errors: None
Firmware: DD-WRT v3.0-r47745 mini (12/04/21)
Router/Version: Netgear WGR614v8/L/WW
File/Kernel: Linux 2.4.37 #67283 Sat Dec 4 05:09:03 +07 2021 mips
Previous/Reset: r47720, No reset,hard reboot after flash
Mode/Status: WAP/Switch
Issues/Errors: none
DD-WRT
Router Model
Netgear R7000
Firmware Version
DD-WRT v3.0-r47745 std (12/04/21)
Kernel Version
Linux 4.4.293 #4545 SMP Fri Dec 3 17:22:02 +07 2021 armv7l
So far no issues other than router mode not getting internet but I figure is because I have to specify a routing table manually.
Also notice when saving changes the router disconnects LAN and comes back like a soft-reboot. Not sure if this is router specific I have an R6400 that does not do that. Still learning on this router model.
Router/Version: Netgear R6250
Firmware: DD-WRT v3.0-r47745 std (12/04/21)
Kernel: Linux 4.4.293 #4545 SMP Fri Dec 3 17:22:02 +07 2021 armv7l
Mode: Gateway, Wireless AP, unbound, CTF & FA Enabled. NAT/QoS Off
Reset: No
Previous : r47720
Upgrade: Web
Temperatures CPU 80.2 °C / WL0 manuel turn off /WL1 57.1 °C
Load: 0.04, 0.02, 0.00
Uptime 3days.
While my Additional Dnsmasq Options:conf-file=/jffs/etc/P
root@DD-WRT:~# cd /jffs/etc
root@DD-WRT:/jffs/etc# wc -l P
120073 P
How ever, Status->Syslog
Dec 8 21:00:17 DD-WRT daemon.info dnsmasq[8703]: using nameserver 127.0.0.1#7053
Dec 8 21:00:17 DD-WRT daemon.info dnsmasq[8703]: using 120048 more nameservers
It seems 120048 more nameservers is not precise, a little bug ?
saphirely dnsmasq doesn't count the comments in files(lines starting with #.....). That's why you think the count is off. _________________ Router: ASUS AC1900(RT-AC68U)
Router/Version: Trendnet TEW811DRU / DD-WRT v3.0-r47745 mini (12/04/21)
File/Kernel: trendnet-811dru-webflash.bin / Linux 4.4.293 #4548 Sat Dec 4 06:21:51 +07 2021 armv7l
Previous/Reset: DD-WRT v3.0-r47665 mini (11/24/21)/ No
Mode/Status: Client, AP / booted clean uptime ~12 mins
Temperatures: CPU 80.2 °C / WL0 54.9 °C / WL1 60.4 °C
Issues/Errors: Issues/Errors: none yet, temps a tad higher but have normalized
Thanks to all, BS and devs