Posted: Sat Dec 04, 2021 7:56 Post subject: New Build - 12/04/2021 - r47745
Welcome to Atheros r47745 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg' 'cat /tmp/var/log/messages', syslog klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Gremlins: reset & configure manually, not restore a backup. Reboot. Search Trac & discuss in forum before opening tickets.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Linksys EA8500...main gateway
DD-WRT v3.0-r47745 std (12/04/21)
Linux 4.9.291 #556 SMP Fri Dec 3 10:38:39 +07 2021 armv7l
GUI install over r47720
all good
#
Netgear WNDR3700 V4
DD-WRT v3.0-r47745 std (12/04/21)
Linux 3.18.140-d6 #130536 Sat Dec 4 10:01:21 +07 2021 mips
GUI install over r47720
all good
################
status LAN don't looky too bad on WNDR3700v4 switch
EA8500 switch
main EA8500 has 2 digets of MAC dropped for (Fat-Deb) --- prolly a bit of alignment issue
and long 'hostnames' take 2 lines
(1) Incoming & Outgoing logs show nothing (not a new issue)
(2) Although the build did load the leases file on reboot, I had to erase /tmp/dnsmasq.leases, uncheck Use JFFS2 for client lease DB, Apply, re-check and Apply, to get leases to start updating to /jffs.
Note: The Status tabs all look good to me. Some IPs are wrapped and hostnames truncated (which is fine for me) but the formatting of the tables is correct. _________________ Netgear R9000
DD-WRT v3.0-r55819 std (04/17/24)
Linux 4.9.337 #722 SMP Wed Apr 17 04:16:49 +07 2024 armv7l
Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
CloudFlare, no SFE, SmartDNS, no QoS
2.4GHz: Vanilla, Airtime Fairness, NG-Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
5GHz: Vanilla, Airtime Fairness, AC/N Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/35Mbps
Oh the squares are supposed to represent arrows.
Well, on my devices no arrows are displayed.
yea, arrows for sorting --- lot of good that does if you still are on 3 second refresh ....they go right back to how the were.
I'm old and can't read/comprehend anything in 3 seconds these days
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Sun Dec 05, 2021 9:15 Post subject:
ho1Aetoo wrote:
@mrjcd
Oh the squares are supposed to represent arrows.
Well, on my devices no arrows are displayed.
Not even on the smartphone.
and thanks for the confirmation with the MAC address!!
sympthom of a non standard "do not use" browser/system font _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Router/Version: TP-Link Archer C7 v2
File/Kernel: Linux 3.18.140-d6 #130514 Sat Dec 4 09:15:40 +07 2021 mips
Previous/Reset: r47720 / no
Mode/Status: Gateway / working
Issues/Errors: Non sofar. Running for a little more than 1 hour
Thanks BS and to everyone who contributed. _________________
1x TP-Link Archer C7 V2.0 r48432 (Primary router at primary location. Former Ziggo repeater)
1x TP-Link Archer C7 V2.0 OpenWrt 21.02.3 (Testing at primary location. Former Ziggo repeater)
1x TP-Link Archer C7 V5.0 r48540 (Secondary router at primary location)
1x TP-Link Archer C7 V5.0 OpenWrt 21.02.3 (Testing at primary location)
1x TP-Link WR1043ND V4.0 OpenWrt 21.02.3 (Testing at primary location)
1x TP-Link WDR4900 V1.3 (green leds) r48646 (Primary router at secondary location)
1x TP-Link WDR4900 V1.3 (blue leds) OpenWrt 21.02.3 (Testing at primary location)
1x TP-Link WDR4900 V1.3 (green leds) OpenWrt 21.02.3 (Testing at primary location)
1x TP-Link WDR4900 V1.3 (green leds) OpenWrt 21.02.3 (Testing at primary location)
1x TP-Link WDR4900 V1.3 (blue leds) r47925 (Testing at secondary location)
1x Linksys WRT160NL r48494 (Guest network with QoS at secondary location)
1x Linksys WRT54G V2.0 r14929 (Switched off at secondary location)
1x Linksys WRT54GL V1.1 r14929
Last edited by urkel on Sun Dec 05, 2021 14:46; edited 1 time in total
All routers will go to default UI and Setting every reboot although the user try to downgrade.
I did not waste the time for discussion!
Broadcom chip may cause break!
Finally, the wan type connection of PPTP does not work! No internet and disconnect many times!
To developer
I just want to try a stable building. If the build of dd-wrt firmware cause many problems and consume times for repairing the network! The report is no meaning so I will use the e-mail to contact and report in the future!
Joined: 16 Nov 2015 Posts: 6445 Location: UK, London, just across the river..
Posted: Sun Dec 05, 2021 17:48 Post subject:
M wrote:
Do not try the recently build!
C7V2
1043NDv2
All routers will go to default UI and Setting every reboot although the user try to downgrade.
I did not waste the time for discussion!
Broadcom chip may cause break!
Finally, the wan type connection of PPTP does not work! No internet and disconnect many times!
To developer
I just want to try a stable building. If the build of dd-wrt firmware cause many problems and consume times for repairing the network! The report is no meaning so I will use the e-mail to contact and report in the future!
To help with the issue you should provide any logs or serial ..so the issue will be identified and chased...do you have any output...
I'm running 47720 on my 1043v2 with no issue so far... but in your case its odd...have a look at urkel report above he is running same Archer Cv2 with no issues ...so, very likely it could be a settings issue...from your side...to say more we need details about your set up...as it could have something wrong...
Im not sure what do you mean about ''Broadcom chip may cause break!'' both units you describe are Q/Atheros... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Last edited by Alozaros on Sun Dec 05, 2021 19:44; edited 2 times in total
Posted: Sun Dec 05, 2021 18:59 Post subject: R47745
Router/Version: R9000
Firmware:DD-WRT v3.0-r47745 std (12/04/21)
File/Kernel:Linux 4.9.291 #598 SMP Thu Dec 2 03:38:36 +07 2021 armv7l
Previous: DD-WRT v3.0-r47720 std (12/02/21)
Mode/Status: Gateway / working
Issues/Errors: LAN connections failed. Had to connect to ethernet port extender/switch for internet connection.
