Router/Version: Netgear R7800
File/Kernel: Linux 4.9.288
Previous/Reset: CLI update / No reset
Mode/Status: Gateway / Working
Issues/Errors: Works fine no errors
Using Vanilla on 2.4 and DD-WRT on 5GHz, WAN, QoS, Wireguard tunnel (now works), DDNS, DNSmasq.
Update method: GUI
Router/Version: TP-Link TL-WDR4900 v1
File/Kernel: Linux 4.4.290 #2400 Fri Nov 5 15:47:34 +07 2021 ppc
Previous/Reset: r47608 / Yes
Mode/Status: Default settings after nvram erase / Seems normal
Issues/Errors: See below
The switchport that was stuck at 10Mb half duplex in previous builds has been solved. I have not tested extensively but for now it seems to work. I tested at 10/100/1000 half and full duplex on the affected port and all work. Even the Switch config GUI shows the correct speed.
swconfig dev switch0 show also shows correct info.
Thanks BS for this fix. My offer for a WDR4900 unit for you still stands, so if you want it let me know.
The resetbutton still doesn't seem to do anything.
A proces resetbutton is running and under Administration GUI it is enabled.
Disabling resetbutton in the GUI doesn't make the resetbutton proces go away.
Enabling resetbutton in the GUI again show that the process is stopped and started again because it receives a new process ID.
Maybe I am operating the reset button wrong but a short press (1 sec) or a long press (>10 sec) do nothing.
The WAN vlan (=vlan2) is attached to br0 to which the wlan0, wlan1 and vlan1 are also attached.
In my opinion vlan2 should not be attached to br0 in the default configuration. It is easily removed from br0 though.
I am confused about buildnumbers.
Currently r47618 is flashed in the WDR4900. When I look at svn I see that the fixes for the switchport are made in 47619 on 05-Nov-2021 at 9:42 AM Changeset [47619] by brainslayer, so I was waiting for a build release with 47619 or higher to be able to test.
But looking at the date and time of the r47618 image for the WDR4900, 05-Nov-2021 20:14 which is later than the fix in 47619.
So I decided to give it a try with r47618 and was surprised that the fix of 47619 was present.
How do the releasenumbers correlate with the changenumbers? _________________
1x TP-Link Archer C7 V2.0 r48432 (Primary router at primary location. Former Ziggo repeater)
1x TP-Link Archer C7 V2.0 OpenWrt 21.02.3 (Testing at primary location. Former Ziggo repeater)
1x TP-Link Archer C7 V5.0 r48540 (Secondary router at primary location)
1x TP-Link Archer C7 V5.0 OpenWrt 21.02.3 (Testing at primary location)
1x TP-Link WR1043ND V4.0 OpenWrt 21.02.3 (Testing at primary location)
1x TP-Link WDR4900 V1.3 (green leds) r48646 (Primary router at secondary location)
1x TP-Link WDR4900 V1.3 (blue leds) OpenWrt 21.02.3 (Testing at primary location)
1x TP-Link WDR4900 V1.3 (green leds) OpenWrt 21.02.3 (Testing at primary location)
1x TP-Link WDR4900 V1.3 (green leds) OpenWrt 21.02.3 (Testing at primary location)
1x TP-Link WDR4900 V1.3 (blue leds) r47925 (Testing at secondary location)
1x Linksys WRT160NL r48494 (Guest network with QoS at secondary location)
1x Linksys WRT54G V2.0 r14929 (Switched off at secondary location)
1x Linksys WRT54GL V1.1 r14929
Posted: Tue Nov 09, 2021 13:57 Post subject: Odd DHCP Lease Issue
I have something odd that I do not remember seeing before. I use DNSMasq and have my usual devices on static leases and let guest devices get their leases automatically. The default lease time is 6h and for the static leases 3d. This morning, I noticed that my devices that should have renewed after three days did not. The remaining time counted down to zero and then stayed there. I have leases saved to JFFS on a USB stick. Any idea what causes this? _________________ Netgear R9000
DD-WRT v3.0-r55819 std (04/17/24)
Linux 4.9.337 #722 SMP Wed Apr 17 04:16:49 +07 2024 armv7l
Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
CloudFlare, no SFE, SmartDNS, no QoS
2.4GHz: Vanilla, Airtime Fairness, NG-Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
5GHz: Vanilla, Airtime Fairness, AC/N Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/35Mbps
Update method: Web
Router/Version: TP-Link TL-WR841ND v10
File/Kernel: DD-WRT v3.0-r47618 std (11/05/21)
Previous/Reset: DD-WRT v3.0-r47608 std (10/28/21) / No
Mode/Status: Client Bridge / Seems normal
Issues/Errors: Nothing to report yet...
so.. the router seems perfectly fine.. i use it for some hours and then, of nothing, the connection dies and i can't get it to work properly again.. i barely can connect and access status page, the ping times go to 5,6,7,8 seconds (not mili)
this time i got the log from status/admin/syslog for the time the issues started before i had to power it off..
i don't know if this is useful.. the red lines here are the red lines in the syslog
Code:
Nov 9 17:34:55 XXXX daemon.info hostapd: wlan0.1: STA aa:aa:aa:aa:aa:aa IEEE 802.11: associated (aid 1)
Nov 9 17:34:55 XXXX daemon.info hostapd: wlan0.1: STA aa:aa:aa:aa:aa:aa RADIUS: starting accounting session C66DD9EE10FDDDAA
Nov 9 17:34:55 XXXX daemon.info hostapd: wlan0.1: STA aa:aa:aa:aa:aa:aa WPA: pairwise key handshake completed (RSN)
[color=red]Nov 9 17:35:43 XXXX daemon.err httpd[1280]: [httpd] : Request Error Code 408: Unexpected connection close in intitial request.[/color]
Nov 9 17:36:11 XXXX daemon.info hostapd: wlan0.1: STA aa:aa:aa:aa:aa:aa MLME: auth request, signal -64 (Accepted)
Nov 9 17:36:11 XXXX daemon.info hostapd: wlan0.1: STA aa:aa:aa:aa:aa:aa IEEE 802.11: authenticated
Nov 9 17:36:11 XXXX daemon.info hostapd: wlan0.1: STA aa:aa:aa:aa:aa:aa MLME: assoc request, signal -64 (Accepted)
Nov 9 17:36:11 XXXX daemon.info hostapd: wlan0.1: STA aa:aa:aa:aa:aa:aa IEEE 802.11: associated (aid 1)
Nov 9 17:36:12 XXXX daemon.info hostapd: wlan0.1: STA aa:aa:aa:aa:aa:aa RADIUS: starting accounting session 1143CE24E77A972F
Nov 9 17:36:12 XXXX daemon.info hostapd: wlan0.1: STA aa:aa:aa:aa:aa:aa WPA: pairwise key handshake completed (RSN)
[color=red]Nov 9 17:36:20 XXXX daemon.err httpd[1280]: [httpd] : Request Error Code 408: Unexpected connection close in intitial request.
Nov 9 17:37:37 XXXX daemon.err httpd[1280]: [httpd] : Request Error Code 408: No request appeared within a reasonable time period.
Nov 9 17:38:38 XXXX daemon.err httpd[1280]: [httpd] : Request Error Code 408: No request appeared within a reasonable time period.
Nov 9 17:38:49 XXXX daemon.err httpd[1280]: [httpd] : Request Error Code 408: No request appeared within a reasonable time period.
Nov 9 17:38:49 XXXX daemon.err httpd[1280]: [httpd] : Request Error Code 408: No request appeared within a reasonable time period. [/color]
Joined: 20 Oct 2009 Posts: 44 Location: Czech Republic
Posted: Tue Nov 09, 2021 19:15 Post subject:
Update Method: GUI
Router/Version: TP-Link ARCHER-C7 v5
File/Kernel: DD-WRT v3.0-r47618 std (11/05/21) / Linux archerc7 3.18.140-d6 #129378
Previous/Reset: Stock / YES
Mode/Status: Gateway & AP (2.4Ghz & 5Ghz / DD-WRT) / Working Well except 5Ghz wifi speed only gets to 370 Mb/s.
Issues/Errors: 3 issues
Services Used: FW|NAT|VLAN|DNSMASQ(DHCP&DNS)|OVPN|DDNS|SSH| NTP|SYSLOG|CRON|USBST|ENTWA(LIGHTTPD&TFTPDHPA)
Issues:
1 - On Status LAN page if i try do delete a dhcp lease, i get an error :
"The connection was reset
The connection to the server was reset while the page was loading."
though if i go backup to the status page i see the dhcp lease was successfully delete.
Tracked it back, last release without this issues was r47206, then r47225,r47256,r47305 was jumping to a blank page (DHCPTable.asp) and from r47608 it started getting the "The connection was reset".
2 - On boot, my Administration->Commands->USB Scripts are called twice:
Nov 9 18:58:06 archerc7 kernel: [ 33.250000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Nov 9 18:58:06 archerc7 kernel: [ 33.280000] ehci-platform: EHCI generic platform driver
Nov 9 18:58:06 archerc7 kernel: [ 33.280000] ehci-platform ehci-platform.0: EHCI Host Controller
Nov 9 18:58:06 archerc7 kernel: [ 33.290000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
Nov 9 18:58:06 archerc7 kernel: [ 33.310000] ehci-platform ehci-platform.0: irq 80, io mem 0x1b000000
Nov 9 18:58:06 archerc7 kernel: [ 33.340000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
Nov 9 18:58:06 archerc7 kernel: [ 33.360000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Nov 9 18:58:06 archerc7 kernel: [ 33.360000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Nov 9 18:58:06 archerc7 kernel: [ 33.370000] usb usb1: Product: EHCI Host Controller
Nov 9 18:58:06 archerc7 kernel: [ 33.380000] usb usb1: Manufacturer: Linux 3.18.140-d6 ehci_hcd
Nov 9 18:58:06 archerc7 kernel: [ 33.380000] usb usb1: SerialNumber: ehci-platform.0
Nov 9 18:58:06 archerc7 kernel: [ 33.390000] hub 1-0:1.0: USB hub found
Nov 9 18:58:06 archerc7 kernel: [ 33.390000] hub 1-0:1.0: 1 port detected
Nov 9 18:58:06 archerc7 kernel: [ 33.420000] ehci-platform ehci-platform.1: EHCI Host Controller
Nov 9 18:58:06 archerc7 kernel: [ 33.420000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
Nov 9 18:58:06 archerc7 kernel: [ 33.440000] ehci-platform ehci-platform.1: irq 81, io mem 0x1b400000
Nov 9 18:58:06 archerc7 kernel: [ 33.470000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
Nov 9 18:58:06 archerc7 kernel: [ 33.470000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
Nov 9 18:58:06 archerc7 kernel: [ 33.480000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Nov 9 18:58:06 archerc7 kernel: [ 33.490000] usb usb2: Product: EHCI Host Controller
Nov 9 18:58:06 archerc7 kernel: [ 33.490000] usb usb2: Manufacturer: Linux 3.18.140-d6 ehci_hcd
Nov 9 18:58:06 archerc7 kernel: [ 33.500000] usb usb2: SerialNumber: ehci-platform.1
Nov 9 18:58:06 archerc7 kernel: [ 33.540000] hub 2-0:1.0: USB hub found
Nov 9 18:58:06 archerc7 kernel: [ 33.550000] hub 2-0:1.0: 1 port detected
Nov 9 18:58:06 archerc7 kernel: [ 33.750000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Nov 9 18:58:06 archerc7 kernel: [ 33.900000] usb 1-1: New USB device found, idVendor=0951, idProduct=16ae
Nov 9 18:58:06 archerc7 kernel: [ 33.900000] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Nov 9 18:58:06 archerc7 kernel: [ 33.910000] usb 1-1: Product: DT microDuo 3C
Nov 9 18:58:06 archerc7 kernel: [ 33.920000] usb 1-1: Manufacturer: Kingston
Nov 9 18:58:06 archerc7 kernel: [ 33.920000] usb 1-1: SerialNumber: 001A4D5F10FAB14119465DD9
Nov 9 18:58:07 archerc7 kernel: [ 34.680000] SCSI subsystem initialized
Nov 9 18:58:07 archerc7 kernel: [ 35.060000] usb-storage 1-1:1.0: USB Mass Storage device detected
Nov 9 18:58:07 archerc7 kernel: [ 35.080000] scsi host0: usb-storage 1-1:1.0
Nov 9 18:58:07 archerc7 kernel: [ 35.080000] usbcore: registered new interface driver usb-storage
Nov 9 18:58:09 archerc7 kernel: [ 36.340000] scsi 0:0:0:0: Direct-Access Kingston DT microDuo 3C PMAP PQ: 0 ANSI: 6
Nov 9 18:58:09 archerc7 kernel: [ 36.630000] sd 0:0:0:0: [sda] 121110528 512-byte logical blocks: (62.0 GB/57.7 GiB)
Nov 9 18:58:09 archerc7 kernel: [ 36.650000] sd 0:0:0:0: [sda] Write Protect is off
Nov 9 18:58:09 archerc7 kernel: [ 36.680000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Nov 9 18:58:09 archerc7 root: WireGuard number of non failed tunnels in fail set: 0
Nov 9 18:58:09 archerc7 kernel: [ 36.830000] sda: sda1
Nov 9 18:58:09 archerc7 kernel: [ 36.860000] sd 0:0:0:0: [sda] Attached SCSI removable disk
Nov 9 18:58:09 archerc7 : [cron] : daemon successfully stopped
Nov 9 18:58:10 archerc7 kernel: [ 37.280000] br0: port 4(wlan1) entered forwarding state
Nov 9 18:58:10 archerc7 kernel: [ 37.360000] br0: port 5(wlan1.1) entered forwarding state
Nov 9 18:58:10 archerc7 kernel: [ 37.440000] br2: port 3(wlan1.2) entered forwarding state
Nov 9 18:58:11 archerc7 kernel: [ 38.920000] br0: port 1(vlan1) entered forwarding state
Nov 9 18:58:12 archerc7 kernel: [ 39.650000] EXT4-fs (sda1): barriers disabled
Nov 9 18:58:12 archerc7 kernel: [ 39.680000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: init_itable=0,nobarrier,nobh,barrier=0
Nov 9 18:58:12 archerc7 : [cron] : daemon successfully started
Nov 9 18:58:12 archerc7 : [cron] : daemon successfully stopped
Nov 9 18:58:13 archerc7 : [cron] : daemon successfully started
Nov 9 18:58:13 archerc7 root: myinit.sh|INF|Start
Nov 9 18:58:13 archerc7 kernel: [ 41.040000] br2: port 1(vlan2) entered forwarding state
Nov 9 18:58:14 archerc7 root: myinit.sh|INF|Start
Tracked it back, and this is happening since the 1st release were this option was implemented (r43381)
3 - 5Gh wifi speed below 400 Mb/s compared to 2020 releases, only 2 releases this year were i could get 400 Mb/s
Speed test done with iperf3 from my pc (ethernet cable) to my samsung-s10 (wifi 5Ghz close to the router)
Router: TL-WDR3600 v1
Firmware: tl-wdr3600_us-webflash.bin (v3.0-r47618 std)
Kernel: Linux 3.10.108-d11 #94124 Fri Nov 5 07:38:32 +07 2021 mips
Status: working
Reset: No
Notes on configuration:
Client
Errors:
1. 5Ghz wireless light is not on (2.4Ghz light works)
Router Model / Version: Netgear XR500
Previous Firmware: DD-WRT v3.0-r47608 std (10/28/21)
Current Firmware: DD-WRT v3.0-r47618 std (11/05/21)
File:: dd-wrt-webupgrade.bin
Kernel: Linux 4.9.288 #532 SMP Fri Nov 5 15:47:45 +07 2021 armv7l
Reset: No
Wireless: Disabled
Routing: Operating - Gateway
Setup: Default
Services: Default
Administration: Default
Uptime: up 4:30, load average: 0.00, 0.02, 0.00
Temperature: CPU 53.115 °C / wlan0 45 °C / wlan1 47 °C
Status: OK
Issues: See Below
In addition to what was reported from the previous build (https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1249427#1249427), I'm having hard time configuring VLANs. Whenever I "Apply Settings" on the "swconfig" tab, whether I make a change or not, the WAN VLAN (VLAN 2) is bridged to the lan bridge (br0).
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Thu Nov 11, 2021 8:15 Post subject:
kernel-panic69 wrote:
The switch config tab isn't completely functional on Atheros (yet?), I think...
yep, xraive better use start up script...my R7800 (witch is the same like XR500) is not playing well with GUI vlan set up ATM _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Router/Version: Netgear R7800
File/Kernel: DD-WRT v3.0-r47618 std (11/05/21)
Previous/Reset: r44483 / No reset
Mode/Status: Working
Issues/Errors: Works fine no errors
Been running for 3-4 days now, no errors or dropouts.
Router/Version: Netgear R7800
File: dd-wrt-webupgrade.bin
Firmware: DD-WRT v3.0-r47618 std (11/05/21) (prev. DD-WRT v3.0-r47608 std (10/28/21))
Kernel: Linux 4.9.288 #532 SMP Fri Nov 5 15:47:45 +07 2021 armv7l
Mode: Gateway, SFE disabled, 2.4G and 5G wifi, Wireguard for external access, WAN to 4G, Keep Alive reboot 6:02 in the morning
Reset: No
Status: Ok, installed it three days ago.