Posted: Fri Sep 24, 2021 9:30 Post subject: New Build - 09/24/2021 - r47481
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
update was ok
All clients connected (NTP, WireGuard, USB, DynDns, Samba, FTP, 15xESP, S10+,S21Ultra, 3xCams,... all ok!).
Connection is stable and Speed is very good!!!
I do a lot of speedtests on 2.4GHz during e.g.15min. This Version is the best that I ever try.
During my tests I get NO connection error. I think the error was gone, please can someone try this Version also with other devices e.g. apple phone...? We will see what happend.......
wlan1:
AP
NG-Gemischt
12+8 HT40
WMM ON
Short GI ON
all other off
VLC on Android cannot stream videos from SMB shares on builds after 47381. It isn't device specific, it's an issue with all my Marvell and QCA devices. Videos will stream on Windows & Linux, so I'm not ruling out a VLC issue.
VLC on Android cannot stream videos from SMB shares on builds after 47381. It isn't device specific, it's an issue with all my Marvell and QCA devices. Videos will stream on Windows & Linux, so I'm not ruling out a VLC issue.
Looks like a file explorer issue. I found a functional alternative and can now stream smb shares on newer builds.
Joined: 14 Sep 2019 Posts: 301 Location: Maine, USA
Posted: Sun Sep 26, 2021 15:16 Post subject:
Router/Version: Linksys WRT1900AC (V1)
File: ddwrt-linksys-wrt1900ac-webflash.bin
Firmware: DD-WRT v3.0-r47481 std (09/24/21)
Kernel: Linux 4.9.282 #2870 SMP Fri Sep 24 03:29:44 +07 2021 armv7l
Mode: Gateway
Previous: New install
Reset?: Y
Status: Working
Picked this up at Goodwill Bargain Barn (where you pay $0.69 per pound for electronics). Unbricked it and it seems fine.
The ports on the "Switch Config" tab look backwards. I have a fussy 100mbs device that doesn't auto-negotiate properly that had been plugged into physical port 4. I used the gui to hard set port 4, and then could no longer get the WAN to connect. No amount of settings in the gui could get the WAN port to reconnect. I eventually cleared nvram and started over and it's running fine now. The fussy device auto-negotiated fine next time around, so I didn't set anything in the "Switch Config" tab again.
I'm not sure if the backwards ports are a 1-4/4-1 issue or if the WAN port is involved somehow.
Joined: 14 Sep 2019 Posts: 301 Location: Maine, USA
Posted: Mon Sep 27, 2021 13:55 Post subject:
SurprisedItWorks wrote:
Ports 1..4 externally are ports 3..0 internally, FWIW.
Thanks. I did a little testing today to confirm.
Code:
Physical gui swconfig
1 4 3
2 3 2
3 2 1
4 1 0
I tried hard setting a LAN port again via the gui and it again rendered the WAN port unusable. LED went from white to orange. Had to restore config and power cycle to get it working again.
In this version it is a problem when loading web pages, it gave me an error when I opened a page randomly, the server cannot be found after a refresh the page loads correctly! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Router/Version: WRT1900ACv1
File/Kernel: :upgrade bin/DD-WRT v3.0-r47481 std (09/24/21)
Previous/Reset: 44048/no reset
Mode/Status: AP
Issues/Errors: Good so far
Stopped trying these for a while since my Android tablet kept hanging up requiring a WiFi toggle. Always returned to 44048.
Someone else in this thread mentioned something about 2.4GHz being solid and that pushed me to limit the Android tablet to 2.4GHz.
Went 4 days that way without issue. I've since turned 5GHz back on for the tablet and been up with that about a day.
I expect to stay on this one even if I have to limit the tablet to 2.4GHz.
Update: Android tablet hangs on 5GHz so I only allow 2.4GHz on it. Everything really stable now. I have various other devices, including Apple devices on 5GHz without an issue.
When transparent mode is enabled the firewall rules include an invalid DROP rule in PREROUTING. Processing of the iptables file halts and there are no iptables rules as a result of this. This was present in the previous release I tested, but I decided to update to see if it still persisted.
I can manually edit the .ipt file and remove the offending rule. At that point privoxy in transparent mode seems to work.
Example from line 10:
--------------------------
-A PREROUTING -p tcp -s 192.168.1.1 -d 192.168.1.1 --dport 80 -j DROP
--------------------------
When attempting to restore the firewall rules the failure appears as:
--------------------------
root@GarageMonster:~# iptables-restore /tmp/.ipt
iptables-restore v1.8.5 (legacy):
The "nat" table is not intended for filtering, the use of DROP is therefore inhibited.
Error occurred at line: 10
Try `iptables-restore -h' or 'iptables-restore --help' for more information.
--------------------------