Posted: Wed Sep 08, 2021 7:48 Post subject: New Build - 09/08/2021 - r47381
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Router/Version: Linksys WRT32X
File/Kernel: DD-WRT v3.0-r47381 std (09/08/21)
Previous/Reset: 09-03-2021-r47305
Mode/Status: AP only
Issues/Errors: successfully updated without reboot.
ESP8266 looks great after reboot. In the previous build r47256 or earlier, WMM support must be enable then disable so that ESp8266 can be connected only 10 mins exactly then re-connected.
Anyone knows why esp8266 can only be connected just 10 mins?
Currently I am running openwrt on wrt1900acs v2 and I found my configuration on the wifi side very stable, I left a video with the tests done and maybe it will help you in one way or another ...
Reset: Erase nvram and reboot, flashed firmware, and ran erase nvram and reboot
Role: NAS and AP.
This is some good firmware. Definitely loving the theme from "the-j0k3r". I stuck with Solarized Dark for my WRT32x. I find it matches pretty well with the color and look of the WRT32x.
Transfer speeds between the computer and the router are blazing fast. the drive attached to the router is a WD-RED-8tb drive formatted as ext4. get transfer rates as high as 750+mbps when downloading torrents.
Router was a bit sluggish at first during first time setup, but now its blazing fast.
Wireless is also pretty good. but im only using the 5ghz mainly. I dont use 2.4ghz much anymore. more of a utility frequency if you ask me.
I give this a pass. I say we also put this firmware as the suggested firmware on the router database page in my humble opinion. _________________ For people who are new to the dd-wrt forums >> http://www.catb.org/~esr/faqs/smart-questions.html#rtfm
barryware wrote:
It takes a "community" to raise a router..
Internet Connection 1
Some Techicolor modem > Linksys WRT3200ACM
Internet connection 2
Ubiquiti Powerbeam Gen 2 > Netgear R9000
Official (but not really) dd-wrt General Discussion element/matrix chat
Router/Version: Linksys WRT1900ACS Ver2 File/Kernel: DD-WRT v3.0-r47381 std (09/08/21) Linux 4.9.282 #2845 SMP Wed Sep 8 05:15:52 +07 2021 armv7l
Previous/Reset: R44048/No Mode/Status: AP Issues/Errors:
So far it looks pretty good. On the 5.0 GHz Band, if I set Channel Width to 80 MHz, the SID doesn't show on my Samsung S9 Android phone. If I set it to 40 MHz or lower the band shows and the SSID is visible and selectable. I have done speed tests, and it seems like a solid connection at the lower rates.
I will report back on stability. What I had seen in the past is it works for about 24 hours and then locks up.
WRT3200ACM V1 ddwrt-linksys-wrt3200acm-webflash.bin / Linux 4.9.282 #2845 SMP Wed Sep 8 05:15:52 +07 2021 armv7l r47305 was previous 9/03/2021/No Reset Mode is AP / router No issues
Pretty decent update, will update if there's any issues with my used features.
Update:
There's only one potential issue I've found on this model: When you log in through the GUI, the session never times out. Not sure if this is a new behavior, but I found that interesting. _________________ Router: Linksys WRT3200ACM WLAN0 and 1 have same SSID
88W8964 802.11ac WLAN0 Mode AP VHT80 80MHz Mixed Mode Channel and Extension Channel Auto Extension LL-6
88W8964 802.11ac WLAN1 Mode AP 20 MHz Mixed Mode Channel Auto
SD8887 802.11ac disabled but visible on GUI and CLI
TX Power 18 dBm
Antenna Gain 0 dBi
U-APSD (Automatic Power Save)Enabled
Protection Mode None
RTS Threshold Disabled
Short Preamble Disabled
Short GI Enabled
Single User Beamforming Enabled
Multi User Beamforming Enabled
AP Isolation Disabled
Beacon Interval 100
DTIM Interval 2
WMM Support Enabled
Radar Detection Disabled
ScanList default
Sensitivity Range (ACK Timing) 500 (Default: 500 meters)
Max Associated Clients 256 (Default: 256 Clients)
Minimum Signal for authenticate -128
Minimum Signal for connection -128
Poll Time for signal lookup 10
Amount of allowed low signals 3
Wireless security is WPA2 Personal CCMP-128 only
QAM256 is on
Last edited by Argenis on Fri Sep 17, 2021 3:05; edited 1 time in total
Router: Linksys WRT1900ACSv2
Firmware DD-WRT v3.0-r47381 std (09/08/21) Previous r47117 std (08/01/21)
Kernel Linux 4.9.282 #2845 SMP Wed Sep 8 05:15:52 +07 2021 armv7l
Reset: No. Uptime 1 day, 2:00
Mode: Enable: Ignore WAN DNS, Shortcut Forwarding Engine, DHCP Server, Use DNSMasq for DNS, DHCP-Authoritative, Forced DNS Redirection.
IGMP Snooping - On.
SmartDNS - Enable: Prefetch Domain, Serve Expired; config - /jffs/etc/smartdns.conf.
Dnsmasq - Enable: No DNS Rebind.
Additional Dnsmasq Options:
dhcp-option=252,"\n", dns-forward-max=300, dhcp-option=br0,6,192.168.1.107 - PiHole powered by OrangePiPC+ with only SmartDNS upstream server.
5 GHz: AP AC/N-Mixed, VNT80, Channel 149+UU
-- Enable: Disassoc Low Ack, Short Preamble, Short GI, Single User Beamforming, WMM, DTIM Interval-2.
2.4 GHz: AP NG-Mixed, HT40, Channel 4+U.
-- Enable: Disassoc Low Ack, Short Preamble, Short GI, WMM, DTIM Interval-2.
Security: WPA2 Personal CCMP-128 (AES), Disable EAPOL Key Retries - Enable.
NAS via USB: - /dev/sda - Block device, size 931.5GiB, Partition: 1-Ext4, 2-Ext4 , 3-swap.
Samba: Protocol Version SMB 2.10\SMB 3.11, Connection Limit -16, Encryption - Off. (For Windows customers.)
NFS Server: - (For Linux customers.)
Shared the same partitions as in Samba.
BitTorrent Transmission Daemon - Disable, but is launched from Startup by the command:
This is due to incorrect support for the "watch-dir" and "watch-dir-enabled" options in the settings.json file of the standard Transmission GUI interface. (There were my posts about this in earlier versions on the forum, but I admit... haven't tested it in a long time, there may have been changes. )
Issues/Errors:
I had to go back to r47117 due to the fact that home wi-fi users complained about frequent loss of connection.
I also had trouble accessing the common GUI interface on this firmware.
Transmission began to write in the log a lot of errors related - as it seemed to me - with the throwing of ports. _________________ Linksys WRT1900ACSv2
Automatically adjustable temperature, always within the range of 59-68°С.
Posted: Sun Sep 19, 2021 4:29 Post subject: trouble with multiple VAP
Router/Version: Linksys WRT32X
File/Kernel:DD-WRT v3.0-r47206 std (08/19/21)
Previous/Reset: DD-WRT v3.0-r47381 std (09/08/21) yes
Mode/Status: AP only
Issues/Errors: found that r47381 release and the one from 09-17-2021 r47461 that 3 VAP's on the 2.4ghz radio result in "channel unknown" in the status even though the radio is enabled, no clients able to connect or see the SSID. When reduced to 2 VAP radio begins to transmit and everything works. rolled back to R47206 found issue does not exist with 3+ VAP's I recall a similar issue like this about a year ago or so that was resolved...?
rev's I found this issue present in:
r47461
r47381
r47305
Posted: Mon Sep 20, 2021 4:41 Post subject: Re: trouble with multiple VAP
bobthenewguy wrote:
Router/Version: Linksys WRT32X
File/Kernel:DD-WRT v3.0-r47206 std (08/19/21)
Previous/Reset: DD-WRT v3.0-r47381 std (09/08/21) yes
Mode/Status: AP only
Issues/Errors: found that r47381 release and the one from 09-17-2021 r47461 that 3 VAP's on the 2.4ghz radio result in "channel unknown" in the status even though the radio is enabled, no clients able to connect or see the SSID. When reduced to 2 VAP radio begins to transmit and everything works. rolled back to R47206 found issue does not exist with 3+ VAP's I recall a similar issue like this about a year ago or so that was resolved...?
rev's I found this issue present in:
r47461
r47381
r47305
alright after extensive testing found that if I roll back to a previous version that worked with 3+ VAP then upgrade to r47461 w\o factory defaulting the config it works. Although.... If I factory default then upgrade and add 3 or more VAP's it doesn't work.