Posted: Wed Aug 25, 2021 6:25 Post subject: New Build - 08/25/2021 - r47256
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
tcp_tw_recycle = Is set to 0
tcp_tw_reuse = Is set to 1
Is this the new default for the builds now if not above is what they are set to at default.
WebUI is now freezing with these new defaults!
AND now try "ubootenv get boot_part" in Command Shell, and see what happens r47225 is when Commands Shell issues started. Have no idea what other Commands are affected really don't give a Sh&t.
Last edited by Justanotherbrokenrouter on Wed Aug 25, 2021 13:45; edited 1 time in total
I saw BS changed the recycle default to 0 with this release, but I also have reuse set to 0, and web browsing is snappy.
Based on change 47246, it appears like recycle=0 and reuse=1 are the defaults. Prior to this release, I also had both set to 0 in the administration-sysctl tab. After upgrading, both stayed set to 0.
Upgraded WRT1200AC v1's from r47225 to r47256 using Brave 1.10.97 (64-bit) running on Linux Mint 20.2 OS hardwired via Cat6.
Successful update and reboot. No reset, nothing disabled prior to update, uptime approx 2+ hrs, wired/wireless connected, vpn up immediately (Expressvpn). SFE, QoS and IPv6 are always disabled. OpenVPN client/DNSMasq and radios always enabled. I do not have any Apple devices. I do not use NAS.
Kernel Version Linux 4.9.280 #2815 SMP Wed Aug 25 01:39:46 +07 2021 armv7l
No issues with a routine update session.
Concerning tcp_tw_recycle and tcp_tw_reuse I had both set to "0" and after update both still at "0". Seems fine with no issues.
May set to BS's new default just to see if there is better performance at 0/1. That's with me assuming 0/1 IS his new default?? Can others confirm the default is now 0/1 since mine stayed at the previous setting??
Based on change 47246, it appears like recycle=0 and reuse=1 are the defaults. Prior to this release, I also had both set to 0 in the administration-sysctl tab. After upgrading, both stayed set to 0.
Ok well thats the difference I keep resetting my build to default when flash while you both are not.
Joined: 08 May 2018 Posts: 14208 Location: Texas, USA
Posted: Wed Aug 25, 2021 14:41 Post subject:
They should be both set to 0, don't know why reuse was left set to 1 in the defaults. I am having fewer webUI issues with both at 0. Please start using the report format in the OP. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Router/Version: WRT1900ACSv1 & WRT1900ACSv2 / r47256
File/Kernel: webflash via Putty SSH / Linux 4.9.280 #2815 SMP Wed Aug 25 01:39:46 +07 2021 armv7l
Previous/Reset: r47117(ACSv1), r47040(ACSv2) / No
Mode/Status: Gateway, OpenVPN Client, FreeRADIUS Server / Up 24+ hrs (ACSv2), Up 5 hrs (ACSv1)
Issues/Errors: This is a strong build, thanks!
I've had some random 5 GHz wifi disconnects and/or inability to immediately reconnect to both units from several different clients, but 2.4 GHz has been rock solid and speeds are fine. Hopefully it's just local interference on 5 GHz.
I did notice something strange about WPA3-Enterprise. Would it be possible to add AES-256 GCM as an available WPA algorithm to the Marvell dd-wrt builds? To discuss: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=330095
Edits: Fixed typos, clarified, and added link for discussion. _________________ My DD-WRT Routers:
Linksys WRT3200ACM - Marvell
Linksys WRT1900ACS - Marvell
Netgear R9000 - Atheros
Netgear R7000 - Broadcom
PC x86-64 VM - Atheros
Last edited by o2bad455 on Sun Aug 29, 2021 6:44; edited 6 times in total
