Flow Acceleration is not showing up in GUI.
According to the wiki, the chip is supported (Northstar)./7444
Did you turn off and on the router after firmware upgrade?
The last time I Restore Factory Defaults after firmware upgrade, then a soft boot, CTF and FA were also NOT available. But after a few cold boots, they appeared again.
Is it normal? I dunno.... I were also not sure whether I edited certain settings that triggered their re-appearance.
_________________ Router: Asus RT-N18U (rev. A1)
Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!
The last time I Restore Factory Defaults after firmware upgrade, then a soft boot, CTF and FA were also NOT available. But after a few cold boots, they appeared again.
Yes, I did. It is also in the wiki that you'll need to restart your router once to get Flow Acceleration, and QoS needs to be Off.
Router/Version: R7000
File/Kernel: DD-WRT v3.0-r47090 std (07/26/21)
Kernel Version: Linux 4.4.276 #3717 SMP Thu Jul 22 03:10:07 +07 2021 armv7l
Previous/Reset: r47086 / No, Remote CLI Update
Mode/Status: GW & AP / Working Well
Issues/Errors: none / none
Services Used: DHCP WAN,IPv6-6to4,NTP,WG Client,VLANx,BRx,SSH,Syslog,Cron,USB Storage,Entware DNSCrypt v2.0.45,YAMon3.4.7
Services Disabled: SFE,QoS,ttraff,Telnet,NAS.Samba
TESTING at Home for OffSite #2
Router/Version: R7000
File/Kernel: DD-WRT v3.0-r47090 std (07/26/21)
Kernel Version: Linux 4.4.276 #3717 SMP Thu Jul 22 03:10:07 +07 2021 armv7l
Previous/Reset: r47086 / No, CLI Update
Mode/Status: GW & AP / Working Well
Issues/Errors: none /none
Services Used: DHCP WAN,IPv6-PD,NTP,VLANx,BRx,SSH,Syslog,Cron,USB Storage,Entware DNSCrypt v2.0.45,YAMon3.4.7
Services Disabled: SFE,QoS,ttraff,Telnet,NAS.Samba
This Router is NOT Deployed to Off-Site #2 yet, TESTING.
All running over 24hours.
Thank-you BrianSlyer for your Great Work and everyone else who makes DD-WRT Great on the Forum! _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
Router: R7000
File: DD-WRT v3.0-r47090 std (07/26/21)
Kernel Version: Linux 4.4.276 #3717 SMP Thu Jul 22 03:10:07 +07 2021 armv7l
Previous/Reset: r41813 / factory reset from gui
Mode: GW
Issues/Errors: Privoxy in transparent mode non-functional. Blocks connection to internet.
I host a website as well as game servers for a few friends behind this router. Previous version worked very well. So far this version is working well, other than the Privoxy. I still have a lot of work to redo and tweak the configuration. I will post back with any issues.
I try to keep the updates to a minimum because this is a amateur production environment. If it's working well I don't update, but I was concerned about the recent Linux exploit and thought it was time for an update. _________________ Netgear XR500
Rogers Ignite Cable
150mbps down/15mbps up
Firmware: v3.0-r47090 std (07/26/21)
Router/Version: Netgear R7000 Kernel: Linux 4.4.276 #3717 SMP Thu Jul 22 03:10:07 +07 2021 armv7l
Previous: v3.0-r47086 std (07/22/21)
Mode/Status: AP wired and wireless / Up and running for 36 hours
Reset: Soft boot before and after upgrade
Temperatures: CPU 61.9 °C / WL0 47.0 °C / WL1 52.0 °C
Issues/Errors: Nothing significant
Updated via webif. No 'nvram erase' this time, last one was in July 2018 (r36325).
Upload and Download speeds are to ISP spec. Nothing unexpected in the syslog.
Current basic R7000 setup (subject to change of course):
- Static WAN IP
- Shortcut Forwarding Engine: CTF, Flow Acceleration: Disabled
- STP - Enabled
- IPv4 only, both WAN and LAN
- LAN DHCP Enabled
- Wireless: AP, Regulatory Domain = CANADA, wl0 Mixed (ch. 6), wl1 AC/N-Mixed (ch. 36, VHT80), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- No custom scripts
- No: ttraf, Tor, VNC, Zabbix, VPN, Radius, OpenVPN
- No: UPnP, DMZ, QoS
- No: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7
Current basic AC68U setup (subject to change of course):
- PPPoE WAN
- Shortcut Forwarding Engine: CTF, Flow Acceleration: Not available
- STP - Enabled
- IPv4 only, both WAN and LAN
- LAN DHCP Enabled
- Wireless: AP, 2.4G - 2VI, 5G 1VI
- 3 VLANs
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled
- USB support - Off
- No custom scripts
- No: ttraf, Tor, VNC, Zabbix, VPN, Radius, OpenVPN
- No: UPnP, DMZ, QoS
- No: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware
FA dropdown is not available. dmesg is as follows:
attaching FA
CHIPID 53010, rev 5
no valid FA Mode.
attach ctf for eth%d
_ctf_attach:attach eth%d
bind ctf to eth if