Posted: Mon Jul 26, 2021 5:04 Post subject: New Build - 07/26/2021 - r47090
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Linksys EA8500...main gateway router
DD-WRT v3.0-r47090 std (07/26/21)
Linux 4.9.276 #334 SMP Thu Jul 22 01:05:54 +07 2021 armv7l
GUI upgrade over r47074
samba share ext4 32GB flash
ovpn server
VLAN on 1 port
both radios good
static DHCP leases
local DNS
a few ports forwarded using 'Port Range Forwarding'
QOS = HFSC CAKE
all good
current wifi clients
other EA8500 used as switch
OVPN sever
samba share 32GB ext4 and 16GB ext4 both USB flash drives
he is also all good
#
Netgear WNDR3700 V4
DD-WRT v3.0-r47090 std (07/26/21)
Linux 3.18.140-d6 #121523 Mon Jul 26 05:58:10 +07 2021 mips
GUI upgrade over r47074
switch / OVPN server
radios good
all good
Reset: yes. ran the command "nvram erase && reboot" in ssh
Mode/Status: AP and NAS
Issues: SAMBA IS WORKING!!! I can access the share without having to create an account! however, i cannot change the name of the hostname of the router! I found that if i go to
Administration > systctl
I can change the host name there. but in doing so, samba stops working! so I have to keep the name set to "DD-WRT".
Also, the web interface is very slow and buggy. I keep having to refresh the page over and over. the web browser I am using specifically is Mozilla Fire Fox.
Router/Version: R7800
File/Kernel: Linux 4.9.276 #336 SMP Mon Jul 26 01:18:52 +07 2021 armv7l
Previous/Reset: r47074 / yes
Mode/Status: Gateway / working with issue
Services Used: Wifi 2,4Ghz + 5Ghz AP's + Vanilla,USB samba and DLNA
Issues/Errors: the last two builds after 47074 constantly has a wifi drops and not reconnect. Only reboot helps to restore wifi for a few time. All 2 last bulds was flashed with nvram clear and configure from zero.
Reset: yes. ran the command "nvram erase && reboot" in ssh
Mode/Status: AP and NAS
Issues: SAMBA IS WORKING!!! I can access the share without having to create an account! however, i cannot change the name of the hostname of the router! I found that if i go to
Administration > systctl
I can change the host name there. but in doing so, samba stops working! so I have to keep the name set to "DD-WRT".
Also, the web interface is very slow and buggy. I keep having to refresh the page over and over. the web browser I am using specifically is Mozilla Fire Fox.
Thank you brainslayer!!!
Samba hostname is actually being taken from Setup -> Basic setup -> Optional Setting -> host name. Changing host name there reflects in samba. I am able to change host name which is shown in network in windows (I use Windows laptop)
