Joined: 08 May 2018 Posts: 14242 Location: Texas, USA
Posted: Thu Jul 22, 2021 15:55 Post subject: New Build - 07/22/2021 - r47086
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Home Main Gateway Router Router/Version: R7800
File/Kernel: DD-WRT v3.0-r47086 std (07/22/21)
Kernel Version: Linux 4.9.276 #334 SMP Thu Jul 22 01:05:54 +07 2021 armv7l
Previous/Reset: r47074 / No, CLI Update
Mode/Status: GW / Working Well
Issues/Errors: none / none
Services Used: DHCP WAN,IPv6-PD,NTP,WG Client,VLANx,BRx,SSH,Syslog,Cron,USB Storage,Entware DNSCrypt v2.0.45,YAMon3.4.7
Services Disabled: WiFi,QoS,ttraff,SFE,Telnet,NAS,Samba
Home Main AP Router Router/Version: R7800
File/Kernel: DD-WRT v3.0-r47086 std (07/22/21)
Kernel Version: Linux 4.9.276 #334 SMP Thu Jul 22 01:05:54 +07 2021 armv7l
Previous/Reset: r47074 / No, CLI Update
Mode/Status: GW(double-nat) & AP / Working Well
Issues/Errors: none / none
Services Used: Static WAN,IPv6 6to4,WiFi Vannilla,NTP,2xWG Clients,VAPx,VLANx,BRx,SSH,Syslog,Cron,USB Storage,Entware DNSCrypt v2.0.45
Services Disabled: QoS,ttraff,SFE,Telnet,NAS,Samba
Thank-you BrianSlyer for your Great Work and everyone else who makes DD-WRT Great on the Forum! _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
Joined: 18 Oct 2015 Posts: 35 Location: Sioux Falls SD
Posted: Fri Jul 23, 2021 3:32 Post subject: iPhone/Safari admin web page issue is still present
Router Model: Netgear R7800
Update method: Web GUI
Firmware Version: DD-WRT v3.0-r47086 std (07/22/21)
Kernel Version: Linux 4.9.276 #334 SMP Thu Jul 22 01:05:54 +07 2021 armv7l
Upgraded from: DD-WRT v3.0-r47074 std (07/20/21)
Reset config: No
Status: Gateway, static leases, QoS, access restrictions, firewall rules (iptables), 2.4 GHz and 5 GHz (vanilla firmware), VLAN tagged trunk port between two r7800s all working
Errors: The iPhone/Safari admin web page issue I first noticed with r47074 is still present. The forum thread on this issue is
Something funky going on with MacOS 11.4/iOS 14.5 and DDWRT. I'm not sure when it was introduced, I've rapidly jumped through a few recent firmwares since leaving 44719 (where I did not have this problem). _________________ R7800 v3.0-r47086 std (07/22/21)
set "tcp_tw_recycle" to 0
Last edited by jimj on Mon Jul 26, 2021 4:14; edited 4 times in total
Reset: yes. Did a hard "scorched earth" reset. flashed back to netgears stock firmware, factory reset, and then abck to dd-wrt followed by another factory reset.
Samba is still broken. I also cannot make an anonymous samba share without having to make a samba account share.
miniDLNA works fine. Bittorrent seems a bit sluggish.
I did not state that I did a 30-30-30 reset. I know better. I explained how I did my reset.
Yes, I did see the changeset. let me ask you all a question.
Have you also tried doing a hard reset yourself and setup everything from scratch? or did you flash to new build while retaining old settings? _________________ For people who are new to the dd-wrt forums >> http://www.catb.org/~esr/faqs/smart-questions.html#rtfm
barryware wrote:
It takes a "community" to raise a router..
Internet Connection 1
Some Techicolor modem > Linksys WRT3200ACM
Internet connection 2
Ubiquiti Powerbeam Gen 2 > Netgear R9000
Official (but not really) dd-wrt General Discussion element/matrix chat
I did not state that I did a 30-30-30 reset. I know better. I explained how I did my reset.
Yes, I did see the changeset. let me ask you all a question.
Have you also tried doing a hard reset yourself and setup everything from scratch? or did you flash to new build while retaining old settings?
reset via reset button, GUI or via CLI does the job...no need going back to stock and all that hassle...
I go back to stock only, if i doubt router hardware functionality...
reset means all from scratch, loading save file afterwards its bad bad idea, especially from a different build...
p.s. there ware positive samba reports, just look around ask the correct person, follow instructions...(im not using samba) _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
I did not state that I did a 30-30-30 reset. I know better. I explained how I did my reset.
1. R7500v2 there is no need to flash factory stock firmware for a hardware reset (button 7 to 10 seconds).
I linked to nvram erase && reboot with links for more explanation. Nobody was talking about 30-30-30.
2. "Yes, I did see the changeset." Then nothing to investigate as of three days ago, maybe configuration.
1. I wanted to make absolutely sure there was no record of any saved values from previous builds. but I will try the commands you were talking about.
2, I saw the changeset he did for the whole anonymous user issue in samba. not the one that's about samba not working at all. I can see the router showing up in windows explorer. but when i click on it, it tells me that it cannot connect to the router.
If i go back to a build before 46979, I am able to make the share and connect to it in windows explorer.
Those users who said samba is working properly altogether is probably because they did not do a factory reset which means there are some values still in their nvram that keep samba working.
Router/Version: Netgear R7800
File/Kernel: DD-WRT v3.0-r47086 std (07/22/21)
Previous/Reset: DD-WRT v3.0-r47040 std (07/12/21) / No
Mode/Status: Gateway / Working with QoS Disabled
Issues/Errors: Firewall Rules Not Applied When QoS Enabled
SFE: Disabled
Enabling QoS for the first time last week, so unknown if QoS worked in previous firmwares.
QoS Details:
Firewall rules (forwarding, masquerading, etc) are applied correctly when QoS is disabled. Access to the WAN works correctly. However, when QoS is enabled, the firewall rules appear not to be applied at all, even after a reboot or power cycle, resulting in no access to the WAN for client (wired and wireless) devices.
Logging into the router via ssh and running manually:
stopservice firewall
startservice firewall
Applies the firewall rules correctly and QoS works as expected. WAN access for all clients works correctly.
Also, pressing the Apply Settings button on the Services > Services screen of the web GUI restarts the firewall correctly, which allows routing and QoS to work as expected.
Results of "iptables -t mangle -nvL" before and after (public IP removed):
Chain OUTPUT (policy ACCEPT 11 packets, 1496 bytes)
pkts bytes target prot opt in out source destination
25 2850 RRDIPT_OUTPUT all -- * * 0.0.0.0/0 0.0.0.0/0
Chain POSTROUTING (policy ACCEPT 419 packets, 189K bytes)
pkts bytes target prot opt in out source destination
434 198K FILTER_OUT all -- * * 0.0.0.0/0 0.0.0.0/0
Chain FILTER_IN (1 references)
pkts bytes target prot opt in out source destination
440 199K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 CONNMARK restore
249 74407 FILTER_br0_IN all -- br0 * 0.0.0.0/0 0.0.0.0/0
0 0 FILTER_wlan1.1_IN all -- wlan1.1 * 0.0.0.0/0 0.0.0.0/0
4 540 SVQOS_SVCS all -- * * 0.0.0.0/0 0.0.0.0/0 mark match 0x0/0x7ffc00
424 190K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 CONNMARK save
424 190K RETURN all -- * * 0.0.0.0/0 0.0.0.0/0
Chain FILTER_OUT (1 references)
pkts bytes target prot opt in out source destination
434 198K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 CONNMARK restore
187 118K FILTER_br0_OUT all -- * br0 0.0.0.0/0 0.0.0.0/0
0 0 FILTER_wlan1.1_OUT all -- * wlan1.1 0.0.0.0/0 0.0.0.0/0
3 188 SVQOS_SVCS all -- * * 0.0.0.0/0 0.0.0.0/0 mark match 0x0/0x7ffc00
419 189K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 CONNMARK save
419 189K RETURN all -- * * 0.0.0.0/0 0.0.0.0/0
Chain FILTER_br0_IN (1 references)
pkts bytes target prot opt in out source destination
24 5673 MARK all -- * * 0.0.0.0/0 0.0.0.0/0 mark match 0x0/0x7ffc00 MARK xset 0x35400/0x7ffc00
247 74296 RETURN all -- * * 0.0.0.0/0 0.0.0.0/0
Chain FILTER_br0_OUT (1 references)
pkts bytes target prot opt in out source destination
2 192 MARK all -- * * 0.0.0.0/0 0.0.0.0/0 mark match 0x0/0x7ffc00 MARK xset 0x35400/0x7ffc00
184 117K RETURN all -- * * 0.0.0.0/0 0.0.0.0/0
Chain FILTER_wlan1.1_IN (1 references)
pkts bytes target prot opt in out source destination
0 0 MARK all -- * * 0.0.0.0/0 0.0.0.0/0 mark match 0x0/0x7ffc00 MARK xset 0x37c00/0x7ffc00
0 0 RETURN all -- * * 0.0.0.0/0 0.0.0.0/0
Chain FILTER_wlan1.1_OUT (1 references)
pkts bytes target prot opt in out source destination
0 0 MARK all -- * * 0.0.0.0/0 0.0.0.0/0 mark match 0x0/0x7ffc00 MARK xset 0x37c00/0x7ffc00
0 0 RETURN all -- * * 0.0.0.0/0 0.0.0.0/0
Chain RRDIPT_FORWARD (1 references)
pkts bytes target prot opt in out source destination
13 2407 RETURN all -- * * 192.168.42.100 0.0.0.0/0
12 5380 RETURN all -- * * 0.0.0.0/0 192.168.42.100
0 0 RETURN all -- * * 192.168.42.220 0.0.0.0/0
0 0 RETURN all -- * * 0.0.0.0/0 192.168.42.220
0 0 RETURN all -- * * X.X.X.X 0.0.0.0/0
0 0 RETURN all -- * * 0.0.0.0/0 X.X.X.X
230 72732 RETURN all -- * * 192.168.42.239 0.0.0.0/0
171 115K RETURN all -- * * 0.0.0.0/0 192.168.42.239
8 1130 RETURN all -- * * 192.168.42.50 0.0.0.0/0
9 6154 RETURN all -- * * 0.0.0.0/0 192.168.42.50
10 1656 RETURN all -- * * 192.168.42.51 0.0.0.0/0
12 2509 RETURN all -- * * 0.0.0.0/0 192.168.42.51
0 0 RETURN all -- * * 192.168.42.2 0.0.0.0/0
0 0 RETURN all -- * * 0.0.0.0/0 192.168.42.2
0 0 RETURN all -- * * 192.168.42.7 0.0.0.0/0
0 0 RETURN all -- * * 0.0.0.0/0 192.168.42.7
Chain RRDIPT_INPUT (1 references)
pkts bytes target prot opt in out source destination
5 877 RETURN all -- eth0 * 0.0.0.0/0 0.0.0.0/0
Chain RRDIPT_OUTPUT (1 references)
pkts bytes target prot opt in out source destination
5 325 RETURN all -- * eth0 0.0.0.0/0 0.0.0.0/0
Chain SVQOS_SVCS (2 references)
pkts bytes target prot opt in out source destination
6 688 RETURN all -- * * 0.0.0.0/0 0.0.0.0/0
Joined: 18 Oct 2015 Posts: 35 Location: Sioux Falls SD
Posted: Sun Jul 25, 2021 21:47 Post subject:
mickelalloy wrote:
Router/Version: Netgear R7800
File/Kernel: DD-WRT v3.0-r47086 std (07/22/21)
Previous/Reset: DD-WRT v3.0-r47040 std (07/12/21) / No
Mode/Status: Gateway / Working with QoS Disabled
Issues/Errors: Firewall Rules Not Applied When QoS Enabled
SFE: Disabled
Enabling QoS for the first time last week, so unknown if QoS worked in previous firmwares.
QoS Details:
Firewall rules (forwarding, masquerading, etc) are applied correctly when QoS is disabled. Access to the WAN works correctly. However, when QoS is enabled, the firewall rules appear not to be applied at all, even after a reboot or power cycle, resulting in no access to the WAN for client (wired and wireless) devices.
Logging into the router via ssh and running manually:
stopservice firewall
startservice firewall
Applies the firewall rules correctly and QoS works as expected. WAN access for all clients works correctly.
Also, pressing the Apply Settings button on the Services > Services screen of the web GUI restarts the firewall correctly, which allows routing and QoS to work as expected.
...
I also have an R7800 running r47086 with SFE disabled, QoS enabled and it's all working fine. Maybe you need to nvram erase && reboot and then manually reconfig?
By "WAN access" you mean access to the Internet through your router? _________________ R7800 v3.0-r47086 std (07/22/21)
set "tcp_tw_recycle" to 0
Router/Version: Netgear R7800
File/Kernel: DD-WRT v3.0-r47086 std (07/22/21)
Previous/Reset: DD-WRT v3.0-r47040 std (07/12/21) / No
Mode/Status: Gateway / Working with QoS Disabled
Issues/Errors: Firewall Rules Not Applied When QoS Enabled
SFE: Disabled
Enabling QoS for the first time last week, so unknown if QoS worked in previous firmwares.
QoS Details:
Firewall rules (forwarding, masquerading, etc) are applied correctly when QoS is disabled. Access to the WAN works correctly. However, when QoS is enabled, the firewall rules appear not to be applied at all, even after a reboot or power cycle, resulting in no access to the WAN for client (wired and wireless) devices.
Logging into the router via ssh and running manually:
stopservice firewall
startservice firewall
Applies the firewall rules correctly and QoS works as expected. WAN access for all clients works correctly.
Also, pressing the Apply Settings button on the Services > Services screen of the web GUI restarts the firewall correctly, which allows routing and QoS to work as expected.
...
I also have an R7800 running r47086 with SFE disabled, QoS enabled and it's all working fine. Maybe you need to nvram erase && reboot and then manually reconfig?
By "WAN access" you mean access to the Internet through your router?
Yes, "WAN access" means the Internet in my description.
Thanks, I'll try erasing it then reconfiguring manually.
Joined: 16 Nov 2015 Posts: 6445 Location: UK, London, just across the river..
Posted: Sun Jul 25, 2021 22:41 Post subject:
mickelalloy wrote:
Router/Version: Netgear R7800
File/Kernel: DD-WRT v3.0-r47086 std (07/22/21)
Previous/Reset: DD-WRT v3.0-r47040 std (07/12/21) / No
Mode/Status: Gateway / Working with QoS Disabled
Issues/Errors: Firewall Rules Not Applied When QoS Enabled
SFE: Disabled
Enabling QoS for the first time last week, so unknown if QoS worked in previous firmwares.
QoS Details:
Firewall rules (forwarding, masquerading, etc) are applied correctly when QoS is disabled. Access to the WAN works correctly. However, when QoS is enabled, the firewall rules appear not to be applied at all, even after a reboot or power cycle, resulting in no access to the WAN for client (wired and wireless) devices.
Logging into the router via ssh and running manually:
stopservice firewall
startservice firewall
Applies the firewall rules correctly and QoS works as expected. WAN access for all clients works correctly.
Also, pressing the Apply Settings button on the Services > Services screen of the web GUI restarts the firewall correctly, which allows routing and QoS to work as expected.
...
I also have an R7800 running r47086 with SFE disabled, QoS enabled and it's all working fine. Maybe you need to nvram erase && reboot and then manually reconfig?
By "WAN access" you mean access to the Internet through your router?
Yes, "WAN access" means the Internet in my description.
Thanks, I'll try erasing it then reconfiguring manually.
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file. .....
also which services you run that may interfere with QoS...SFE, Access restrictions and ect. ...more details and testing needed... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file. .....
also which services you run that may interfere with QoS...SFE, Access restrictions and ect. ...more details and testing needed...
I have not erased the nvram and manually reconfigured yet.
Additional Configuration Info: SFE Disabled, STP Enabled, WDS AP (5GHz - With 2 R7500v2 WDS Stations), AP (2GHz),Guest VAP (2GHz), OpenVPN Server, No Access Restrictions, UPnP Disabled, DMZ Disabled
WDS How-To Used:https://wiki.dd-wrt.com/wiki/index.php/WDS_Linked_router_network QoS: Interface Priority (Currently Both Set to Manual 0,0,0 for Troubleshooting)
