Posted: Mon Jul 12, 2021 7:50 Post subject: New Build - 07/12/2021 - r47040
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Netgear WNDR3700 V4
DD-WRT v3.0-r47040 std (07/12/21)
Linux 3.18.140-d6 #120863 Mon Jul 12 07:17:46 +07 2021 mips
GUI upgrade over r47033 from laptop connected to EA8500 OVPN server via cell phone hotspot.
#
Linksys EA8500
DD-WRT v3.0-r47040 std (07/12/21)
Linux 4.9.274 #319 SMP Sat Jul 10 10:37:53 +07 2021 armv7l
GUI upgrade over r47033 from laptop connected to WNDR3700V4 OVPN server via cell phone hotspot.
SAMBA share ok / ovpn servers ok
When I get back to the homeworld I might put this on main EA8500 but r47033 has been good without problems
I noticed that you stopped adding the info about needing to manually update the config to fix broken NG-mixed mode. Is this because the issue has been resolved or you're just tired of bringing it up for every build? _________________ --Netgear R7800--
DD-WRT v3.0-r49492 std (07/14/22)
I noticed that you stopped adding the info about needing to manually update the config to fix broken NG-mixed mode. Is this because the issue has been resolved or you're just tired of bringing it up for every build?
gave up mentioning.. figured everyone knows by now.. _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
Joined: 03 Nov 2015 Posts: 317 Location: Florida, USA
Posted: Tue Jul 13, 2021 0:29 Post subject:
Router:TP Link WR1043ND Ver.2 WDS AP
Firmware: DD-WRT v3.0-r47040 std (07/12/21)
Kernel: Linux 3.18.140-d6 #120835 Mon Jul 12 06:24:05 +07 2021 mips
Reset: NO
Errors: None so far
Router: TP Link WR1043ND Ver.2 WDS Stations X2
Firmware: DD-WRT v3.0-r47040 std (07/12/21)
Kernel: Linux 3.18.140-d6 #120835 Mon Jul 12 06:24:05 +07 2021 mips
Reset: NO
Errors: None so far
Swift GUI upgrade from r46885 with no issues, Only up a few hrs. with no disconnects and wifi speed is unchanged.
All GOOD here... Just Handshakes and Time Stamps !
My "true" speeds are 40108 kbps for download and 5047 kbps for upload.
Whatever settings i put in QOS..95%..90%..85%..80%...and i try all qdiscs it cannot take care of bufferbloat.in dsl reports it has lag spikes. _________________ Tp-Link WR-1043ND v3
Firmware:DD-WRT v3.0-r47040 (07/12/21)
Upgrade: via CLI from r47000. No issues with upgrade. Did not reset.
Issues:
1) GUI can be painfully slow at times. Opening a telnet also freezes when GUI is acting up - no prompt. Firefox is the only browser that sort of works on my Macbook.
2) Very occasional messages in dmesg on one of my 7800s - doesn't seem to cause a problem:
[45297.299107] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode
[45297.307319] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode
[215403.018329] ath10k_pci 0001:01:00.0: failed to lookup txq for peer_id 31 tid 0
[215403.018362] ath10k_pci 0001:01:00.0: failed to lookup txq for peer_id 31 tid 0
Linksys WRT1900ACSv1: wifi disabled - using it as a semi-intelligent switch only. Can't get wifi to work reliably post-r44048.
Two Netgear r7800s - as hardwired WAPs in router-mode with nearly identical WIFI settings to the 3200ACM above, just different wifi channels. Vanilla firmware, SFE enabled, DNSmasq disabled, NAS disabled, firewall disabled, QoS disabled,
Clients: Apple MACOS x 4, IOS x 4, Apple TV, Chromecast Audio x 2, Eufy doorbells, Lutron Caseta, Axis Camera, Samsung TV, Nest thermostat, EtekCity outlets (Espressif), BlueSound/BlueOS devices...
Update Method: Web GUI
Router/Version: Netgear R7800
File/Kernel: DD-WRT v3.0-r47040 std (07/12/21)
Previous/Reset: DD-WRT v3.0-r46604 std (05/09/21) | No
Mode/Status: Standard Router
Issues/Errors: Port forwarding UI is/has been buggy for me, at least for my router model. In the past I've tried both with and without resets, seems to be the same behavior no matter what. When I modify/create a new rule, another one is broken/disabled in an endless game of whack-a-mole. This isn't a new problem (here, here, and here) but it's a pain to have to haphazardly and randomly delete/re-create rules until it somehow just works again despite entering the same data into the same fields and checking the SVN issues on the proper syntax. I'm dealing with it, but just keeping it on folks' radars.
