Posted: Mon Jun 28, 2021 10:05 Post subject: New Build - 06/28/2021 - r47000
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Linksys EA8500...main gateway router
DD-WRT v3.0-r47000 std (06/28/21)
Linux 4.9.273 #298 SMP Sun Jun 27 15:00:34 +07 2021 armv7l
GUI install over r46885
ovpn server / samba ext4 32GB flash stick / vlan on 1 port + wlan0.1 via br1
all working fine --- BUT damn thing would NOT forward any ports after install
until I went to webif page '../Forward.asp' and clicked the 'Apply Settings' ... all good now.
very annoying & of course that killed access to my webserver for few minutes
Netgear WNDR3700 V4
DD-WRT v3.0-r47000 std (06/28/21)
Linux 3.18.140-d6 #119625 Mon Jun 28 12:16:53 +07 2021 mips
GUI install over r46974
switch / ovpn server / samba ext4 32GB flash stick
Joined: 16 Nov 2015 Posts: 5687 Location: UK, London, just across the river..
Posted: Mon Jun 28, 2021 21:33 Post subject:
Router Model Netgear R7800
Firmware Version DD-WRT v3.0-r47000 std (06/28/21)
Kernel Version Linux 4.9.273 #300 SMP Mon Jun 28 08:38:41 +07 2021 armv7l
reset: NO/YES manual rebuild
status: Operational 3h+
errors: i do suspect, Vanilla its not loading even if its selected via GUI, and its been like that for the last few builds at least..
Jan 1 02:00:23 R7800 kern.warn kernel: [ 23.495577] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0-vanilla/firmware-6.bin failed with error -2
Jan 1 02:00:23 R7800 kern.info kernel: [ 23.719462] ath10k_pci 0001:01:00.0: found firmware features ie (4 B)
Jan 1 02:00:23 R7800 kern.info kernel: [ 23.719496] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
Jan 1 02:00:23 R7800 kern.info kernel: [ 23.724884] ath10k_pci 0001:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
Jan 1 02:00:23 R7800 kern.info kernel: [ 23.737075] ath10k_pci 0001:01:00.0: firmware ver 3.15-00018 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps,peer-fixed-rate crc32 b1095cd9
that is the last logs regarding it...
my 5Ghz is disabled, only 2,4Ghz is in use...i constantly have the same errors with my I-phones and other devices that ware typical for DDWRT wi-fi firmware..drops and stalls and nothing in the log regarding it except those lines above, on boot... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 51741 WAP
TP-Link WR1043NDv2 -DD-WRT 52054 Gateway/DoT DNS,AP Isolation,Ad-Block,Firewall,Forced DNS,VPN,VLAN
TP-Link WR1043NDv2 -DD-WRT 52148 Gateway/DoT DNS,Ad-Block,Firewall,Forced DNS,x3 VLAN(no-wifi)
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Netgear R7800 --DD-WRT 52148 Gateway/DoT DNS,AD-Block,AP&Net Isolation,x3 VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 52095 Gateway/StubbyDoT/DNS,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Netgear R7000 ---DD-WRT 52148 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3 VLAN,VPN (no-wifi)
NOT USING 5Ghz ANYWHERE
Stubby for DNS over TLS I DNSCrypt v2 by mac913
Router/Version: Netgear R7800 / r47000 (06/28/21)
File/Kernel: CLI Flash dd-wrt-webupgrade.bin / Linux 4.9.273 #300 SMP Mon Jun 28 08:38:41 +07 2021 armv7l
Previous/Reset: r46885 (06/05/21) > r46750 > r46690 > r46604 > r46329 > r46239 > r46220 > r46166 / No reset
Mode/Status: Gateway AP / VANILLA, Mixed 20 MHz, Ch 1 & 149, TX Power 30 dBm, Short Preamble, ttraff disabled
Issues/Errors: None / 1 day 5 minutes uptime with no errors
DD-WRT ver 10.4-ddwrt-9984-tW-13-6284M api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate crc32 88f56884
ver 3.15-00018 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps,peer-fixed-rate crc32 b1095cd9
Both firmware types load firmware-5.bin after driver cannot find firmware-6.bin, typical file does not exist and normal operation.
Kernel: Linux router2 4.9.273 #300 SMP Mon Jun 28 08:38:41 +07 2021 armv7l DD-WRT
Upgrade: via CLI from r46854. No issues with upgrade. Did not reset.
Status: Running great for a couple of days now.
The only three issues are:
1) GUI can be painfully slow at times. Opening a telnet also freezes when GUI is acting up - no prompt. Firefox is the only browser that sort of works on my Macbook.
2) I occasionally get these in dmesg. Doesn't seem to cause a problem:
[ 1194.480708] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode
[ 1194.480741] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode
3) I get these messages occasionally with 802.11r enabled but they do not seem to cause a problem:
[114741.791463] Rekeying PTK for STA 0e:02:25:5e:3f:62 but driver can't safely do that.
[114842.299918] Rekeying PTK for STA 0e:02:25:5e:3f:62 but driver can't safely do that.
Router/Version: Netgear R7800
File/Kernel: DD-WRT v3.0-r47000 std (06/28/21) Linux 4.9.273 #300 SMP Mon Jun 28 08:38:41 +07 2021 armv7l
Previous/Reset: v3.0-r37495M kongat (10/28/18 ), installed via gui, with reset. Manually re-populate settings
Mode/Status: Gateway/PPPoE Dual, 4 VLANs, 3VAPs for each radio, 2 openvpn clients, 1 server (vpn as yet untested)
Issues/Errors: This is a massive upgrade for me. But I'm having very basic problems.
First, is it possible that PPPoE Dual isn't working? I can't connect to WAN. There is nothing about WAN or PPP in /var/log/messages. Asking to connect from the WAN status page seemingly does nothing.
In addition: bizarre error trying to run a custom executable that is there and has correct permissions:
root@DD-WRT main:/jffs/bin# ls -l mdns-repeater
-rwxr-xr-x 1 root root 8812 Jan 1 1970 mdns-repeater
root@DD-WRT main:/jffs/bin# ./mdns-repeater
-sh: ./mdns-repeater: not found
Finally, the vlan & ethernet port settings don't seem to be working properly (maybe this is the cause of the WAN/PPPoE problem). My prior config, which I'm still running at startup:
# set up vlans 11-14 and ethernet ports
# port 1 (==4 logical) is tagged for trunking, port 4 (==1) is on IoT bridge; ports 2 & 3 are default bridge 0
swconfig dev switch0 set enable_vlan 1
swconfig dev switch0 vlan 1 set ports "2 3 6"
swconfig dev switch0 vlan 11 set ports "4t 6t"
swconfig dev switch0 vlan 12 set ports "4t 6t"
swconfig dev switch0 vlan 13 set ports "4t 6t"
swconfig dev switch0 vlan 14 set ports "1 4t 6t"
swconfig dev switch0 set apply
vconfig add eth1 11
vconfig add eth1 12
vconfig add eth1 13
vconfig add eth1 14
# Add these interfaces to the appropriate bridges and bring them up
brctl addif br0 eth1.11
brctl addif br1 eth1.12
brctl addif br2 eth1.14
brctl addif br3 eth1.13
ifconfig eth1.11 up
ifconfig eth1.12 up
ifconfig eth1.13 up
ifconfig eth1.14 up
On the (new, to me) "Switch Config" page I've tried to match this, but maybe not correctly (see attachment). Notably, the eth1.?? interfaces don't reliably appear. It's not clear to me what if anything I should remove from my prior config.
In particular, eth1.11 (for example) does not appear in the output from ifconfig, and the following is output from creating and then trying to remove in vconfig:
root@DD-WRT main:~# vconfig add eth1 11
vconfig: ioctl error for add: File exists
root@DD-WRT main:~# vconfig rem eth1.11
vconfig: ioctl error for rem: No such device
So, so far, not working for me.
*Addendum* By accident, I restored the settings from my old Kong Build. Surprisingly, they worked! The WAN came up and the vlans were correct. In looking through the config, the main difference is the "Switch Config" page shown with my old settings (image attached). So I restored with my manually entered settings to see if I could reproduce them by matching the workings settings on the "Switch Config page". Unfortunately, this still does not work. It seems there are some magical nvram settings from the old build that are making this build work. Although everything I've tested now seems to be working with my old kong settings restore, I'm wary of leaving these possibly obsolete settings. It seems remarkable that it works at all.
Last edited by jtbr on Thu Jul 01, 2021 21:24; edited 3 times in total