Netgear WNR3500L v2 bugs

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Author Message
thommy181
DD-WRT User


Joined: 16 Mar 2019
Posts: 353
Location: Szczecin, Poland EU

PostPosted: Sat Jun 19, 2021 9:09    Post subject: Netgear WNR3500L v2 bugs Reply with quote
I have the Netgear WNR3500L v2. It can't boot on firmware from 6/16/2021 and 6/18/2021. I'm update device via ssh and after reboot router can't start. Start procedure dump:
Quote:

Decompressing...done

CFE for WNR3500Lv2 version: v1.0.9
Build Date: Fri May 6 11:54:17 CST 2011
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
NFLASH Boot partition size = 524288(0x80000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.136
CPU type 0x19749: 480MHz
Tot mem: 131072 KBytes

Device eth0: hwaddr XXX, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Checking crc...done.
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: ........ 4429432 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000

In this situation I must back to older version. I don't know why version from 6/13/2021 is erased from server. Currently I'm back to version from 6/10/2021. Earlier I had version from 6/13/2021 and that was last good version for WNR3500L v2. Any newer version are incorrect for this device. Actually I have usable router on version 6/10/2021 and I have dump of start procedure. I see there many bugs and problems like no such file, can't open location, can't create file, unsupported device, unsupported command. That problems should be fix in my opinion. I'm attach full log.
Quote:

Found a AMD NAND flash with 2048B pages or 128KB blocks; total size 128MB
Decompressing...done

CFE for WNR3500Lv2 version: v1.0.9
Build Date: Fri May 6 11:54:17 CST 2011
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
NFLASH Boot partition size = 524288(0x80000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.136
CPU type 0x19749: 480MHz
Tot mem: 131072 KBytes

Device eth0: hwaddr xx, ipaddr 192.x, mask 255.x
gateway not set, nameserver not set
Loader:raw Filesys:tftp Dev:eth0 File:192.x:vmlinuz Options:(null)
Loading: Failed.
Could not load 192.x:vmlinuz: Timeout occured
Checking crc...done.
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: ........ 4965960 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 4.4.271 (root@linux) (gcc version 11.1.0 (OpenWrt GCC 11.1.0 r16896+6-3c46ba053d) ) #10007 Thu Jun 10 06:05:29 +07 2021
prom_init:194
CPU0 revision is: 00019749 (MIPS 74Kc)
Found a AMD NAND flash with 2048B pages or 128KB blocks; total size 128MB
Using bcma bus
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
Primary instruction cache 32kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Zone ranges:
Normal [mem 0x0000000000000000-0x0000000007ffefff]
HighMem empty
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000000000000-0x0000000007ffefff]
Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffefff]
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32511
Kernel command line: console=ttyS0,115200 root=1f05 rootfstype=squashfs noinitrd init=/bin/sh
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 124396K/131068K available (3673K kernel code, 175K rwdata, 780K rodata, 224K init, 611K bss, 6672K reserved, 0K cma-reserved, 0K highmem)
SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:128
CPU: BCM5357 rev 2 at 480 MHz
clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7963585194 ns
sched_clock: 32 bits at 240MHz, resolution 4ns, wraps every 8947848189ns
console [ttyS0] enabled
Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
BRCM Errata: Enable CPU_WAIT
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 256 (order: -1, 3072 bytes)
NET: Registered protocol family 16
PCI: no core
PCI: no core
PCI: scanning bus 0
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
PCI: Fixing up bridge
PCI: Fixing up bus 0
clocksource: Switched to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
serial8250_init
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8, base_baud = 1250000) is a U6_16550A
brd: module loaded
pflash: found no supported devices
ERROR: Unknown flash, device_id:0x00
bcmsflash: found no supported devices
Creating 2 MTD partitions on "brcmnand":
0x000000500000-0x000002000000 : "linux"
0x000004000000-0x000007f00000 : "ddwrt"
Boot partition size = 524288(0x80000)
lookup_nflash_rootfs_offset: offset = 0x500000
found trx at 500000, len =26558464
scan filesys at 6D1000
nflash: squash filesystem with lzma found at offset 500000
Creating 4 MTD partitions on "nflash":
0x000000000000-0x000000080000 : "cfe"
0x000000080000-0x000000200000 : "nvram"
0x000000500000-0x000002000000 : "nandimage"
0x0000006d1000-0x000002000000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
add netgear boarddata for pflash if exists
add netgear boarddata for sflash if exists
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Broadcom Watchdog Timer: 0.07 initialized.
GACT probability NOT on
Mirror/redirect action on
Simple TC action Loaded
netem: version 1.3
u32 classifier
Performance counters on
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1943 buckets, 7772 max)
nf_conntrack_rtsp v0.7 loading
xt_time: kernel timezone is -0000
gre: GRE over IPv4 demultiplexor driver
nf_nat_rtsp v0.7 loading
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Bridge firewalling registered
8021q: 802.1Q VLAN Support v1.8
startup nvram driver
found nvram
max nvram space = 65536
VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
Freeing unused kernel memory: 224K
init : starting devinit
cannot open /dev/nvram
udevtrigger[837]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
init : no previous bootfails detected! (all ok)
init : starting Architecture code for broadcom
boardnum 3500L
boardtype 0x052b
boardrev 02
nvram invalid, erase
Booting device: Netgear WNR3500L v2
create ctf proc
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x0
et_module_init: et_txq_thresh set to 0xce4
et_module_init: et_rxlazy_timeout set to 0x3e8
et_module_init: et_rxlazy_framecnt set to 0x20
et_module_init: et_rxlazy_dyn_thresh set to 0
robo attach
robo id 3115
attach ctf for eth%d
_ctf_attach:attach eth%d
bind ctf to eth if
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.164.18 (r692288)
wl: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
_ctf_attach:attach wl0
switch id 15
switch id32 53115
b5301x_common: found switch: BCM53115, rev 8
bcm_robo_config_vlan_fun vid=1, vlan->members=0x11e, vlan->untag=0x1e
bcm_robo_config_vlan_fun ports=1 2 3 4 8t
bcm_robo_config_vlan_fun vid=2, vlan->members=0x101, vlan->untag=0x101
bcm_robo_config_vlan_fun ports=0 8
cannot open /proc/switch/eth0/reset
cannot open /proc/switch/eth0/enable_vlan
cannot open /proc/switch/eth0/vlan/1/ports
cannot open /proc/switch/eth0/vlan/2/ports
watchdog : daemon successfully started
/etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
cannot open /proc/sys/net/ipv4/ip_conntrack_max
/etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
cannot open /proc/sys/net/ipv4/ip_conntrack_max
resetbutton : resetbutton daemon successfully started
vconfig: ioctl error for add: File exists
vconfig: ioctl error for add: File exists
bcm_robo_config_vlan_fun vid=1, vlan->members=0x11e, vlan->untag=0x1e
bcm_robo_config_vlan_fun ports=1 2 3 4 8t
bcm_robo_config_vlan_fun vid=2, vlan->members=0x101, vlan->untag=0x101
bcm_robo_config_vlan_fun ports=0 8
bridge : bridge br0 successfully added
device br0 entered promiscuous mode
check vlan1
name=[vlan1] lan_ifname=[br0]
br0: Invalid argument
bridge : interface vlan1 successfully added to bridge br0
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
check eth1
name=[eth1] lan_ifname=[br0]
br0: Invalid argument
total vif count 1
eth1: Not supported
base addr xxx
local bit addr xxx
eth1: Invalid argument
eth1: Not supported
eth1: Not supported
eth1: Operation not permitted
nbw = 20
channel 6, val 20
0, 1000, 0, 6
spec 1006
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
enable bss eth1 0 (0)
total vif count 1
eth1: Not supported
base addr xxx
local bit addr 16:59:C0:87:2A:D0
eth1: Invalid argument
eth1: Not supported
eth1: Not supported
eth1: Operation not permitted
eth1: Invalid argument
nbw = 20
channel 6, val 20
0, 1000, 0, 6
spec 1006
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
enable bss eth1 0 (0)
wl: Unsupported
wl: Unsupported
bridge : interface eth1 successfully added to bridge br0
device eth1 entered promiscuous mode
br0: port 2(eth1) entered forwarding state
br0: port 2(eth1) entered forwarding state
br0: port 1(vlan1) entered forwarding state
br0: port 1(vlan1) entered forwarding state
device br0 left promiscuous mode
device br0 entered promiscuous mode
ifconfig: ioctl 0x8914 failed: Address not available
device br0 left promiscuous mode
method hwmon not found
device vlan2 entered promiscuous mode
method udhcpd not found
CTF: disabled
sfe : shortcut forwarding engine successfully stopped
cp: can't stat '/tmp/mycron.d/*': No such file or directory
cp: can't stat '/jffs/mycron.d/*': No such file or directory
cp: can't stat '/mmc/mycron.d/*': No such file or directory
rmmod: eoip: No such file or directory
wland : daemon successfully started
cron : daemon successfully started
dnsmasq : daemon successfully started
cat: can't open '/proc/sys/net/netfilter/nf_conntrack_flush': No such file or directory
cannot open /proc/sys/net/ipv6/neigh/default/gc_thresh1
cannot open /proc/sys/net/ipv6/neigh/default/gc_thresh2
cannot open /proc/sys/net/ipv6/neigh/default/gc_thresh3
httpd : httpd server started at port 80
httpd : http daemon successfully started
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
fast-classifier (PBR safe v2.1.6b): starting up
fast-classifier: registered
sfe : shortcut forwarding engine successfully started
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip6tables v1.8.5 (legacy): can't initialize ip6tables table `mangle': Address family not supported by protocol
Perhaps ip6tables or your kernel needs to be upgraded.
ip6tables v1.8.5 (legacy): can't initialize ip6tables table `mangle': Address family not supported by protocol
Perhaps ip6tables or your kernel needs to be upgraded.
ip6tables v1.8.5 (legacy): can't initialize ip6tables table `mangle': Address family not supported by protocol
Perhaps ip6tables or your kernel needs to be upgraded.
ip6tables v1.8.5 (legacy): can't initialize ip6tables table `mangle': Address family not supported by protocol
Perhaps ip6tables or your kernel needs to be upgraded.
ip6tables v1.8.5 (legacy): can't initialize ip6tables table `mangle': Address family not supported by protocol
Perhaps ip6tables or your kernel needs to be upgraded.
ip6tables v1.8.5 (legacy): can't initialize ip6tables table `mangle': Address family not supported by protocol
Perhaps ip6tables or your kernel needs to be upgraded.
ip6tables v1.8.5 (legacy): can't initialize ip6tables table `mangle': Address family not supported by protocol
Perhaps ip6tables or your kernel needs to be upgraded.
sfe : shortcut forwarding engine successfully started
device vlan2 left promiscuous mode
udhcpc: started, v1.33.1
ttraff : traffic counter daemon successfully started
udhcpc: sending discover
total vif count 1
eth1: Not supported
base addr xxx
local bit addr 16:59:C0:87:2A:D0
eth1: Invalid argument
eth1: Not supported
eth1: Not supported
eth1: Operation not permitted
eth1: Invalid argument
nbw = 20
channel 6, val 20
0, 1000, 0, 6
spec 1006
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
enable bss eth1 0 (0)
total vif count 1
eth1: Not supported
base addr xxx
local bit addr 16:59:C0:87:2A:D0
eth1: Invalid argument
eth1: Not supported
eth1: Not supported
eth1: Operation not permitted
eth1: Invalid argument
nbw = 20
channel 6, val 20
0, 1000, 0, 6
spec 1006
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
enable bss eth1 0 (0)
wl: Unsupported
wl: Unsupported
udhcpc: sending discover
br0: port 2(eth1) entered forwarding state
br0: port 1(vlan1) entered forwarding state
udhcpc: sending discover
nas : wait for network initnas : start nas lan
nas : start nas for wl0
method guest_nas not found
nas : start nas lan
nas : start nas for wl0
httpd : daemon successfully stopped
httpd : httpd server shutdownhttpd : httpd server started at port 80
httpd : http daemon successfully started
resetbutton : daemon successfully stopped
resetbutton : resetbutton daemon successfully started
[USB] checking...
/opt/etc/init.d/rcS: No such file or directory
/jffs/etc/init.d/rcS: No such file or directory
/mmc/etc/init.d/rcS: No such file or directory
killall: proxywatchdog.sh: no process killed
/mnt/smbshare
umount: can't unmount /mnt/smbshare: No such file or directory
rmmod: cifs: No such file or directory
rmmod: fscache: No such file or directory
killall: schedulerb.sh: no process killed
killall: wdswatchdog.sh: no process killed
The Milkfish Router Services
ERROR: Necessary service setting not found: milkfish_username - aborting.
The Milkfish Router Services
Restoring SIP ddsubscriber database from NVRAM...
Empty.
The Milkfish Router Services
Restoring SIP ddaliases database from NVRAM...
Empty.
random: nonblocking pool is initialized
Sponsor
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum