Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Mon May 31, 2021 5:21 Post subject: Re: Asus RT-AC87U
kooper2013 wrote:
Router/Version: Asus RT-AC87U
File/Kernel: asus_rt-ac87u-firmware.trx
Previous/Reset: r46733
Mode/Status: WAP, wg-client, 2.4+5G, DHCP server, SFE on, no fancy config
Issues/Errors: unusable
Unusable for me.
First no GUI access (via LAN), but wg and internet OK. 3 times off/on, then ssh-access and GUI for some time. Took LOGs, see attachment.
wifi: SSIDs were sent, but no device could connect. Access lost entirely after F5 on tab Tunnels.
Reset by button, restored previous config, same issue.
Back to r46733.
according to your log, your wan port is disabled or your 2.4 wifi interface is in client mode. everything else seem to work. _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Mon May 31, 2021 5:26 Post subject:
turbowells wrote:
Router/Version: Asus RT-N12D
File: dd-wrt.v24-#####_NEWD-2_K3.x_mega.bin
Firmware: DD-WRT v3.0-r46816 mega (05/30/21)
Kernel: Linux 4.4.269 #9704 Sun May 30 06:37:47 +07 2021 mips
Mode: Default settings
Previous: r46442
Reset?: Y
Status: Not working, no WAN IP assigned. Last working version is r46442. Did a few "nvram clear && reboots".
the provided information does not help. too much is missing. swconfig dev switch0 show output for instance. _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Mon May 31, 2021 7:05 Post subject:
turbowells wrote:
Router/Version: Asus RT-N12D
File: dd-wrt.v24-#####_NEWD-2_K3.x_mega.bin
Firmware: DD-WRT v3.0-r46816 mega (05/30/21)
Kernel: Linux 4.4.269 #9704 Sun May 30 06:37:47 +07 2021 mips
Mode: Default settings
Previous: r46442
Reset?: Y
Status: Not working, no WAN IP assigned. Last working version is r46442. Did a few "nvram clear && reboots".
i tested now a RT-N12D, but found no issues. all is working as expected. will now just try if wan is working.
edit:
found the wan port problem and fixed it _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Router/Version: Buffalo WZR1750DHP File/Kernel: 46816 Previous/Reset: 45735 / No Mode/Status: 2G Client bridge, 5G AP, no WAN Issues/Errors: Switch dead
Dead switch, for a very short time pingeable (less than a minute, web interface starting but never readable). WLAN working as long as one doesn't connect the router via cable. Same behaviour for 46788, working again on 46750.
Linksys EA6900 is working in 46788 though, different setup (2G AP, WAN via WAN port), but firmware images are identical to Buffalo WZR21750.
Router/Version: WZR-1750DHP2
Firmware: DD-WRT v3.0-r46816 std (05/30/21)
Kernel: Linux 4.4.269 #3242 SMP Sun May 30 03:22:26 +07 2021 armv7l
Mode: Router, PPPOE ,Wireless AP. CTF Enabled. NAT ON and QOS Off.
Reset: Nope.
Status: Whenever I turn on the bittorrent clients like Bitcomet V1.77, it crashes PPPoE connection everytime and stops the entire WAN connection.
It’s ok as I switch to SFE mode.
Joined: 12 Dec 2007 Posts: 783 Location: Pittsburgh, PA USA
Posted: Mon May 31, 2021 14:19 Post subject:
Updated two Netgear AC1450s and a Linksys EA6700 from 46788. All are being used as wired access points (WAN disabled, DHCP server disabled). I just did an update, no reset.
After update, the routers booted up and pinged a few times, then stopped pinging. No GUI or SSH access. I was able to recover the EA6700 using TFTP. The Netgears required more drastic intervention (https://midnightme.com/2015/03/16/how-to-unbrick-or-fix-a-netgear-ac1450-router/). I'm back on 46788, restored config, and all are working now. _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Mon May 31, 2021 14:32 Post subject:
lfb wrote:
Router/Version: Buffalo WZR1750DHP File/Kernel: 46816 Previous/Reset: 45735 / No Mode/Status: 2G Client bridge, 5G AP, no WAN Issues/Errors: Switch dead
Dead switch, for a very short time pingeable (less than a minute, web interface starting but never readable). WLAN working as long as one doesn't connect the router via cable. Same behaviour for 46788, working again on 46750.
Linksys EA6900 is working in 46788 though, different setup (2G AP, WAN via WAN port), but firmware images are identical to Buffalo WZR21750.
already fixed. enable wan as a workaround. this happens only if wan is disabled (or wifi is in client mode) _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Mon May 31, 2021 14:34 Post subject:
dpp3530 wrote:
Updated two Netgear AC1450s and a Linksys EA6700 from 46788. All are being used as wired access points (WAN disabled, DHCP server disabled). I just did an update, no reset.
After update, the routers booted up and pinged a few times, then stopped pinging. No GUI or SSH access. I was able to recover the EA6700 using TFTP. The Netgears required more drastic intervention (https://midnightme.com/2015/03/16/how-to-unbrick-or-fix-a-netgear-ac1450-router/). I'm back on 46788, restored config, and all are working now.
same for you. enable wan. i fixed the issue already internally. fix will be released tomorrow since building takes a while _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Router/Version: Netgear Nighthawk R7000P
File/Kernel: netgear-r7000p-webflash.bin; Linux version 4.4.269 (root@linux) (gcc version 11.1.0 (OpenWrt GCC 11.1.0 r16592-aabc632023) ) #3202 SMP Fri May 28 02:56:10 +07 2021;
Firmware: DD-WRT v3.0-r46788 std (05/28/21)
Time: 13:03:46 up 1 day, 16:21, load average: 1.56, 1.55, 1.54
Previous/Reset: r46772, no reset
Mode/Status: Gateway (PPPoE)/2.4GHz & 5GHz AP/DHCP server/DNS Server/YaMON3/Samba
Also running syslog-ng and user-space NFSV3 via opkg.
Issues/Errors: Occasionally seeing this in the logs:
Code:
May 31 12:03:34 R7000P kernel: CONSOLE: 168178.085 wl0: Proxy STA [redacted]:79 link is already gone !!??
May 31 08:03:47 R7000P dnsmasq-dhcp[12433]: DHCPREQUEST(br0) [redacted].28 [redacted]:79
May 31 08:03:47 R7000P dnsmasq-dhcp[12433]: DHCPACK(br0) [redacted].28 [redacted]:79 nest-thermostat
Note the wl0 in the first message. The device, nest-thermostat, is on the 5GHz WiFi, wl1. (Timestamps are also odd, with the dnsmasp-dhcp getting timezone conversions applied twice - I'm in GMT-4 - but that's a long outstanding issue.)
However, this is the only hiccup; despite this everything seems to be running smoothly.
EDIT: Fixed hardware from "Nighthack" to "Nighthawk", although a Netgear Nighthack would be a unique device.
Joined: 16 Mar 2019 Posts: 353 Location: Szczecin, Poland EU
Posted: Tue Jun 01, 2021 10:25 Post subject: New Build - 05/30/2021 - r46816
Router/Version: Netgear WNR3500L v2
Kernel: Linux 4.4.269 #9688 Sun May 30 06:19:46 +07 2021 mips
Reset: No
Mode: Internet gateway, WIFI AP, Dnsmasq server
Issues: WAN port work little better than earlier, I see vlan0 in switch config tab
Status: Working
Uptime: ~42 h
I'm update device via ssh. Router working rather good. WAN performance is little better than earlier. I have 280 - 290 mbit/s on internet speedometer. ISP serve me ~315 mbit (test on rj-45 cord without router). The WNR3500L v2 have all gigabit ports, but it's rather unavailable speed.