Joined: 08 May 2018 Posts: 14221 Location: Texas, USA
Posted: Sat Apr 24, 2021 15:02 Post subject: New Build - 04/24/2021 - r46446
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• DNScrypt 1.95 can still be used in the GUI, but v2 (not compatible) requires Golang and thus Entware. #6246
• WDS does not work on Broadcom ARM devices(only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Use client or repeater instead.
• VAPs not working at bootfixed for unbridged VAPs in40562 - 40566. Effective startup commandsdiscussion thread is here.
• If start-up scripts do not work from USB add a delay, e.g. wait script or 'sleep 25'.
• Broadcom ARM devices if 5 GHz channels are missing, via Telnet/SSH: 'nvram set brcm_unlock=1' 'nvram commit' 'reboot'
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Posted: Sat Apr 24, 2021 16:03 Post subject: Netgear Nighthawk R7000
Router/Version: Netgear R7000 Firmware: DD-WRT v3.0-r46446 std (04/24/21) Kernel: Linux 4.4.267 #2623 SMP Fri Apr 23 07:31:02 +07 2021 armv7l Mode: Gateway, Wireless AP. Reset: Nope. Previous: 04-23-2021-r46442 Status: Working so far, still testing. CPU Temps higher. Temperatures: CPU 64.7 °C / WL0 50.0 °C / WL1 55.3 °C
Logs.txt
Description:
Full system logs. MAC scrubbed, password scrubbed, the fun stuff at the bottom as usual!
Router/Version: Netgear R6250
Firmware: DD-WRT v3.0-r46446 std (04/24/21)
Kernel: Linux 4.4.267 #2623 SMP Fri Apr 23 07:31:02 +07 2021 armv7l
Mode: Gateway
Reset: Yes
Previous: I didn't note it, but it was from a year ago.
Status: GOOD.
It's been running for about a day.
Working well.
However, when I went into the console I noticed three programs running that weren't there with my last firmware version.
telnetd
ttraff
irqbalance
Apparently ttraff saves traffic stats into nvram or something? I don't want that. Maybe ages your nvram. If I wasn't using the console I'd want a GUI option to kill it and weight its body down with bricks at the bottom of a lake.
Isn't irqbalance for 65536 core machines? (Or 16 or whatever.) Has there been any discussion if this helps a two-core little router? I mean, Dr. Slayer and his minions really ought to tell us if this does any good or not.
Irqbalance had my ethernet interrupt on one core instead of both, which is exactly how I had it when I bothered about affinities.
But if it in practice is always set to one core, maybe just set it manually and turn off packet steering as well? That's how I had it.
But my internet's not fast enough to tell the difference.
Router/Version: LINKSYS WRT54GL
Firmware: DD-WRT v3.0-r46446 std (04/24/21)
Reset: Yes
Status: Access through https is not possible, I have tried with version 46239_vpn_generic, with version 44715_vpn_generic and with others and none of them allow me to access the webgui via https, I can only access the webgui via http.
Moderator note 04.27.2021: Image size should be no wider than 768 pixels per current forum rules and guidelines.
Router/Version: LINKSYS WRT54GL
Firmware: DD-WRT v3.0-r46446 std (04/24/21)
Reset: Yes
Status: Access through https is not possible, I have tried with version 46239_vpn_generic, with version 44715_vpn_generic and with others and none of them allow me to access the webgui via https, I can only access the webgui via http.
Moderator note 04.27.2021: Image size should be no wider than 768 pixels per current forum rules and guidelines.
sorry for asking the trivia question :
Did you tick the "HTTPS" Protocol in the "Web Access" group under Administration > Management, and then Save, Apply & reboot the router?
Router/Version: Asus RT-AC66U /
File/Kernel: dd-wrt-46316-Asus_RT-AC66U.trx / Linux 4.4.267 #8375 Sat Apr 24 15:27:29 +07 2021 mips
Previous/Reset: v3.0-r46316 / no
Mode/Status: AP, Gateway, Router / OK
Issues/Errors: no / no
Last edited by elatllat on Mon May 17, 2021 12:35; edited 2 times in total
Router/Version: LINKSYS WRT54GL
Firmware: DD-WRT v3.0-r46446 std (04/24/21)
Reset: Yes
Status: Access through https is not possible, I have tried with version 46239_vpn_generic, with version 44715_vpn_generic and with others and none of them allow me to access the webgui via https, I can only access the webgui via http.
Moderator note 04.27.2021: Image size should be no wider than 768 pixels per current forum rules and guidelines.
sorry for asking the trivia question :
Did you tick the "HTTPS" Protocol in the "Web Access" group under Administration > Management, and then Save, Apply & reboot the router?
Yes of course, but it not work.
Can anyone access the webgui via https with the Linksys WRT54GL router, please?
Joined: 08 May 2018 Posts: 14221 Location: Texas, USA
Posted: Wed Apr 28, 2021 3:56 Post subject:
Yhoni wrote:
IONK wrote:
Yhoni wrote:
Router/Version: LINKSYS WRT54GL
Firmware: DD-WRT v3.0-r46446 std (04/24/21)
Reset: Yes
Status: Access through https is not possible, I have tried with version 46239_vpn_generic, with version 44715_vpn_generic and with others and none of them allow me to access the webgui via https, I can only access the webgui via http.
Moderator note 04.27.2021: Image size should be no wider than 768 pixels per current forum rules and guidelines.
sorry for asking the trivia question :
Did you tick the "HTTPS" Protocol in the "Web Access" group under Administration > Management, and then Save, Apply & reboot the router?
Yes of course, but it not work.
Can anyone access the webgui via https with the Linksys WRT54GL router, please?
Thanks.
Thanks.
This question was already answered here. I don't think any of the <4MB flash devices that have https webUI functionality working, but if it does work, I am sure there is likely a startup script to kill httpd and restart it involved. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net