Posted: Mon Apr 19, 2021 12:07 Post subject: New Build - 04/19/2021 - r46395
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Router/Version: R9000
File/Kernel: dd-wrt_r9000-webupgrader-46395.bin
Previous/Reset: dd-wrt_r9000-webupgrade-r46316.bin
Mode/Status: WDS AP (5 GHz), WAP (5 GHz), AP (2.4 GHz)
Issues/Errors: Lost "Radioname" info on Status->Wireless->Wireless Nodes->Clients. Soft and Hard reboots did not restore. Also lost Wireless Packet info->Received(RX) packets info on same tab for wlan0 (WDS AP 5 GHz). Always shows 0K, no error.
Issues/Errors: Lost "Radioname" info on Status->Wireless->Wireless Nodes->Clients. Soft and Hard reboots did not restore. Also lost Wireless Packet info->Received(RX) packets info on same tab for wlan0 (WDS AP 5 GHz). Always shows 0K, no error.
Confirmed no Radioname but Wireless Packet Info (RX) is working as usual. It is incrementing every three seconds per refresh rate _________________ Netgear R9000
DD-WRT v3.0-r55819 std (04/17/24)
Linux 4.9.337 #722 SMP Wed Apr 17 04:16:49 +07 2024 armv7l
Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
CloudFlare, no SFE, SmartDNS, no QoS
2.4GHz: Vanilla, Airtime Fairness, NG-Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
5GHz: Vanilla, Airtime Fairness, AC/N Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/35Mbps
Router Model: TP-Link ARCHER-C5 v1
Kernel Version: Linux 3.18.140-d5
Previous/Reset: 04/13/2021 - r46329 / No
Mode/Status: Gateway /2.4 GHz,5.0 GHz, IPv4, Port Forwarding, NTP TimeSync, Samba, VPN
Issues/Errors: router is resetting itself every 30 seconds , When is connected usb drive 128 GB router restarts. When is unplugged usb drive router works. Not working wireless 5g light/diode.
Joined: 05 Oct 2008 Posts: 666 Location: Helsinki, Finland / nr. Alkmaar, Netherlands
Posted: Tue Apr 20, 2021 8:48 Post subject:
johnnyNobody999 wrote:
Router/Version: R9000
File/Kernel: dd-wrt_r9000-webupgrader-46395.bin
Previous/Reset: dd-wrt_r9000-webupgrade-r46316.bin
Mode/Status: WDS AP (5 GHz), WAP (5 GHz), AP (2.4 GHz)
Issues/Errors: Lost "Radioname" info on Status->Wireless->Wireless Nodes->Clients. Soft and Hard reboots did not restore. Also lost Wireless Packet info->Received(RX) packets info on same tab for wlan0 (WDS AP 5 GHz). Always shows 0K, no error.
I have for ever overlooked the Radioname column even existing in that location. On my R7800 and probably also on my old WZR-HP-G300NH, which is in a vastly different location, there has always been the need to look up MAC addresses from the LAN table ...
It would be real nice to have the same hostname there, which is on the LAN page. I do wonder why radioname? Clients radios don't have names as such, or do they?
Router/Version: R9000
File/Kernel: dd-wrt_r9000-webupgrader-46395.bin
Previous/Reset: dd-wrt_r9000-webupgrade-r46316.bin
Mode/Status: WDS AP (5 GHz), WAP (5 GHz), AP (2.4 GHz)
Issues/Errors: Lost "Radioname" info on Status->Wireless->Wireless Nodes->Clients. Soft and Hard reboots did not restore. Also lost Wireless Packet info->Received(RX) packets info on same tab for wlan0 (WDS AP 5 GHz). Always shows 0K, no error.
I have for ever overlooked the Radioname column even existing in that location. On my R7800 and probably also on my old WZR-HP-G300NH, which is in a vastly different location, there has always been the need to look up MAC addresses from the LAN table ...
It would be real nice to have the same hostname there, which is on the LAN page. I do wonder why radioname? Clients radios don't have names as such, or do they?
Packet counters count as usual.
It's my understanding that if the client has been assigned a hostname then it should show up in the Radioname column. Although all my devices have a hostname, the only Radionames that show up are the WDS Station routers hostname in the WDS AP status page and the WDS AP hostname shows up in each of the WDS Station status pages. After upgrading 2 firmwares ago, the WDS AP hostname still shows up in the WDS Stations but none of the WDS Stations show up in the WDS AP anymore. None of my other wireless client hostnames show up in the WDS AP, ever.
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Wed Apr 21, 2021 11:39 Post subject:
MLandi wrote:
johnnyNobody999 wrote:
Issues/Errors: Lost "Radioname" info on Status->Wireless->Wireless Nodes->Clients. Soft and Hard reboots did not restore. Also lost Wireless Packet info->Received(RX) packets info on same tab for wlan0 (WDS AP 5 GHz). Always shows 0K, no error.
Confirmed no Radioname but Wireless Packet Info (RX) is working as usual. It is incrementing every three seconds per refresh rate
radioname is not always shown on qca chipsets. this is normal. its caused by the device firmware offloading. sometimes its shown. sometimes not. and more important. radioname is only shown for dd-wrt wifi clients. its a non standard feature which is only supported by dd-wrt devices (and mikrotik). so to make it clear. the client must be a dd-wrt router too _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Issues/Errors: Lost "Radioname" info on Status->Wireless->Wireless Nodes->Clients. Soft and Hard reboots did not restore. Also lost Wireless Packet info->Received(RX) packets info on same tab for wlan0 (WDS AP 5 GHz). Always shows 0K, no error.
Confirmed no Radioname but Wireless Packet Info (RX) is working as usual. It is incrementing every three seconds per refresh rate
radioname is not always shown on qca chipsets. this is normal. its caused by the device firmware offloading. sometimes its shown. sometimes not. and more important. radioname is only shown for dd-wrt wifi clients. its a non standard feature which is only supported by dd-wrt devices (and mikrotik). so to make it clear. the client must be a dd-wrt router too
Thanks for the info. All the client routers are Netgear R7800 with dd-wrt installed.
Moderator edit 04.21.2021: We are pretty sure you'd be posting a screenshot of the release in this thread, not some other thread. No need to do a screenshot with that information contained in it. Just focus on the pertinent information, please. Thank you!
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Wed Apr 21, 2021 21:08 Post subject:
johnnyNobody999 wrote:
Additional info on the packet counter issue.
Moderator edit 04.21.2021: We are pretty sure you'd be posting a screenshot of the release in this thread, not some other thread. No need to do a screenshot with that information contained in it. Just focus on the pertinent information, please. Thank you!
i dont see an issue, u have wlan0 selected, yet nothings connected on wlan0. wlan0.X and wlan0.staX have their own counters.
BrainSlayer wrote:
MLandi wrote:
johnnyNobody999 wrote:
Issues/Errors: Lost "Radioname" info on Status->Wireless->Wireless Nodes->Clients. Soft and Hard reboots did not restore. Also lost Wireless Packet info->Received(RX) packets info on same tab for wlan0 (WDS AP 5 GHz). Always shows 0K, no error.
Confirmed no Radioname but Wireless Packet Info (RX) is working as usual. It is incrementing every three seconds per refresh rate
radioname is not always shown on qca chipsets. this is normal. its caused by the device firmware offloading. sometimes its shown. sometimes not. and more important. radioname is only shown for dd-wrt wifi clients. its a non standard feature which is only supported by dd-wrt devices (and mikrotik). so to make it clear. the client must be a dd-wrt router too
it seems to only display when the client is a ddwrt ath9k wds station, ath10k wds stations wont display it on the host (cause of radio fw as said?). _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
Moderator edit 04.21.2021: We are pretty sure you'd be posting a screenshot of the release in this thread, not some other thread. No need to do a screenshot with that information contained in it. Just focus on the pertinent information, please. Thank you!
I posted the screenshot in case someone could see something I overlooked. By the way, all the WDS stations connect to wlan0 on the WDS AP and I did see receive packets counted on a prior firmware. I believe it was r46177.