Posted: Sat Apr 03, 2021 13:38 Post subject: New Build - 04/03/2021 - r46259
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Virtual Interface on 5 Ghz Radio set to AC-Only / VHT80 is not avaliable in Setup/Networking when i want to assign it to a bridge or to a new DHCP server. With Mixed / Full (20Mhz) it works. Can anyone confirm this?
no I cannot confirm, it is all there
I reset to factory settings, set wlan0 to AC and VHT80.
then I created an unbridged VAP
I had to restart the router because something hung up.
but after that wlan0.1 was present in the network tab also at DHCP server etc.
Joined: 21 Aug 2019 Posts: 120 Location: Here, There And Everywhere
Posted: Mon Apr 05, 2021 12:49 Post subject:
Router/Version: Netgear R7800
File/Kernel: DD-WRT v3.0-r46259 std (04/03/21)/Linux 4.9.264
Previous/Reset: No
Mode/Status: Gateway, Wireguard / Working OK
Issues/Errors: None so far.
Router/Version: TP-Link Archer C7v5
File/Kernel: DD-WRT v3.0-r46259 std (04/03/21)/Linux 3.18.140-d5
Previous/Reset: No
Mode/Status: Access point / Working OK
Issues/Errors: None so far.
Archer C7v5 works much better than with previous version. DD-WRT firmware.
@tatsuya46 where to enter your ng-mixed fix? Can't find hostapd config anywhere... While it does not seem necessary (for our devices), I'm still curious.
Router/Version: Netgear R9000
Firmware: DD-WRT v3.0-r46259 std (04/03/21)
Kernel: Linux 4.9.264 #562 SMP Wed Mar 31 20:56:59 +07 2021 armv7l
File/Upload: dd-wrt-webupgrade.bin / Upload using GUI
Mode: Gateway/AP
Reset: Yes
Previous: DD-WRT v3.0-r46239 std (04/01/21)
Status: Working Fine running DD-WRT firmaware
Errors/Issues: Yes
I have portforwarding setup in a script on a usb on jffs, which I execute using WINSCP so the DDWRT GUI is immediately populated - this works exactly as it should.
However, once populated, if I then make any changes directly using the GUI and use 'Save' or 'Apply Settings', the same 4 portforwards that are near the top of the GUI always disappear, and i'm left with 4 blank fields at the bottom of the list, as show in the pic below...
This only happens if I make changes to the portforwarding fields directly within the GUI and then try to save or apply settings whilst on the portforwarding page. If I'm on another page, using the 'save' or 'apply settings' button makes no difference to the portforwarding page, but, in any case, obviously, settings do not 'save' when leaving a page without saving first anyway. I don't know how far back this would have been an issue, as I've only just come across it. But, definitely a bug in this firmware.
Things go back to normal and the portforwards are once again properly populated if I once again execute the script using WINSCP.