Posted: Sun Mar 21, 2021 11:00 Post subject: New Build - 03/21/2021 - r46130
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues:
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Router/Version: Linksys WRT1900ACS v2
File: ddwrt-linksys-wrt1900acsv2-webflash.bin
Firmware: DD-WRT v3.0-r46130 std (03/21/21) (prev. DD-WRT v3.0-r45993 std (03/12/21))
Kernel: Linux 4.9.262 #2501 SMP Sun Mar 21 04:24:37 +07 2021 armv7l
Mode: Gateway, 2.4G and 5G wifi, Wireguard for external access, WAN to 4G, Keep Alive reboot 6:02 in the morning
Reset: No
Status: 5:28h up, ok, load average 0.00, 0.00, 0.00, Temperatures CPU 73.2 °C / WL0 46.0 °C / WL1 47.7 °C.
Upgraded 3200ACM from DD-WRT v3.0-r45993 std (03/12/21) no settings reset, all seems to be working fine (that I use).
There's only one warning in syslog and it's no biggie, I specify MTU on the OpenVPN client.
Mar 21 15:26:02 3200ACM daemon.warn openvpn[1820]: --mtu-disc is not supported on this OS
Will report if there's any issues.
Edit: This release has been massively solid, very low CPU usage, and although it is using 40% of the RAM, I'm OK with that with how stable this build is. _________________ Router: Linksys WRT3200ACM WLAN0 and 1 have same SSID
88W8964 802.11ac WLAN0 Mode AP VHT80 80MHz Mixed Mode Channel and Extension Channel Auto Extension LL-6
88W8964 802.11ac WLAN1 Mode AP 20 MHz Mixed Mode Channel Auto
SD8887 802.11ac disabled but visible on GUI and CLI
TX Power 18 dBm
Antenna Gain 0 dBi
U-APSD (Automatic Power Save)Enabled
Protection Mode None
RTS Threshold Disabled
Short Preamble Disabled
Short GI Enabled
Single User Beamforming Enabled
Multi User Beamforming Enabled
AP Isolation Disabled
Beacon Interval 100
DTIM Interval 2
WMM Support Enabled
Radar Detection Disabled
ScanList default
Sensitivity Range (ACK Timing) 500 (Default: 500 meters)
Max Associated Clients 256 (Default: 256 Clients)
Minimum Signal for authenticate -128
Minimum Signal for connection -128
Poll Time for signal lookup 10
Amount of allowed low signals 3
Wireless security is WPA2 Personal CCMP-128 only
QAM256 is on
Last edited by Argenis on Wed Mar 24, 2021 8:38; edited 1 time in total
After a few hours I can't log onto the router anymore. I still have access to the internet and the NAS.
I am using 5GHz WiFi and FF 86 on W10 from a Surface Pro 7 1900ACS
EDIT: Eventually Wifi drops altogether, it starts with me being able to see the 5 and 2.4 channels but not log on (says there is problem authenticating), then I eventually can't see them at all and do a manual reboot at the WRT itself with the power switch, oddly my wired Nvidia Box can could still read the NAS (playing video from the NAS via SMB)
Last edited by ruprect on Wed Mar 24, 2021 10:54; edited 1 time in total
