New Build - 02/11/2021 - r45735

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page 1, 2, 3  Next
Author Message
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 8415
Location: Texas, USA

PostPosted: Thu Feb 11, 2021 15:27    Post subject: New Build - 02/11/2021 - r45735 Reply with quote
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specific recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.


Downloads: (DD-WRT website) HTTPS & FTP (try another if a link does not work)

CLI Flash: 'cd /tmp' then 'wget {file URL}' (or 'curl -k {file URL} -o {file}') with http (not https) or ftp. Then 'write {file} linux'.

Repository: Trac SVN changelog since last build r45729 (GitHub mirror)

Notes:
OpenVPN version 2.5.0 and Guides
WireGuard 1.0.20200908/Tools: Guides, PBR, Kill Switch, Inbound Firewall, Naming of Peers, Status, Key. Thanks BS & egc!
• CVE-2019-14899 VPN fix (applicability depends on VPN setup) and GUI toggle since r41813.
Experimental build option for Broadcom 8MB+ K2.x devices (limited currently): broadcom_K3X_mipsel32r1
• Broadcom MIPS devices are now on kernel 4.4.
• Dnsmasq version 2.84 released with r45632 (2.83 at r45563, prerelease since r45036).
In-kernel Samba (ksmbd 3.3.4+): default min/max versions changed, WSD support, ANTFS and NTFS3 kernel mode drivers.

Issues, observations, and/or workarounds reported:
DNScrypt 1.95 can still be used in the GUI, but v2 (not compatible) requires Golang and thus Entware. #6246
WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Use client or repeater instead.
VAPs not working at boot fixed for unbridged VAPs in 40562 - 40566. Effective startup commands discussion thread is here.
If start-up scripts do not work from USB add a delay, e.g. wait script or 'sleep 25'.
Broadcom ARM devices missing 5GHz channels, via Telnet/SSH: 'nvram set brcm_unlock=1' 'nvram commit' 'nvram reboot'

Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.

Example Template:
Code:
[b]Router/Version: [/b]
[b]File/Kernel: [/b]
[b]Previous/Reset: [/b]
[b]Mode/Status: [/b]
[b]Issues/Errors: [/b]

_________________
Official Forum Rules, Guidelines & Helpful InformationFirmware FAQInstallation WikiWhere Do I Download Firmware?
DON'T use Chromium-based browsersRTFM/STFW TL;DR is NOT an excuse. • Why Should I Care What Color the Bikeshed Is?
Please DO NOT PM me with questions; Ask in the forum. ---------------------- Linux User #377467 counter.li.org / linuxcounter.net
Sponsor
jrscs
DD-WRT User


Joined: 09 Aug 2010
Posts: 276

PostPosted: Thu Feb 11, 2021 17:48    Post subject: Reply with quote
Router/Version: RT-AC87U A1
Firmware: DD-WRT v3.0-r45735 std (02/11/21)
Kernel: Linux 4.4.255 #2028 SMP Thu Feb 11 12:14:17 +06 2021 armv7l
Previous: DD-WRT v3.0-r45729 std (02/10/21)
Mode/Status: Gateway/AP/Ok
Reset: No
Setup Using: 2.4 GHz, 2.4 GHz guest (VAP), 5.0 GHz, IPv4, DNSMasq, Port Forwarding, NTP TimeSync, Wake-on-WAN (internet), and Wireguard
Issues/Errors: OK

_________________
Netgear R7800 - DD-WRT v3.0-r45767 std (02/17/21)
Asus AC87U A1 - DD-WRT v3.0-r45767 std (02/17/21)
Repeater Bridges(s)
Asus AC68R A1 - DD-WRT v3.0-r45767 std (02/17/21)
Netgear R6400 V2 - DD-WRT v3.0-r45767 std (02/17/21)
Asus AC66U A1 - DD-WRT v3.0-r45767 giga (02/17/21)
flyzipper
DD-WRT User


Joined: 21 Feb 2016
Posts: 469

PostPosted: Thu Feb 11, 2021 19:17    Post subject: Reply with quote
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r45735 std (02/11/21)
Kernel: Linux 4.4.255 #2020 SMP Wed Feb 10 10:47:21 +06 2021 armv7l
Previous: r45729
Mode/Status: Gateway / working
Issues/Errors: Working well so far.

Uptime: 1hr 4mins
Upgrade: via web UI, no issues
Reset: no
Temperatures: CPU 67.5 °C / WL0 46.5 °C / WL1 52.5 °C
Abboo
DD-WRT User


Joined: 03 Apr 2016
Posts: 170

PostPosted: Thu Feb 11, 2021 20:28    Post subject: Reply with quote
Same problem as explained in build r45711. Reverted back to build r45592

Extract from build r45711
My diagnosis of the NAS problem: the file sharing path is /mnt; there should also be this path which is in the older builds, /mnt/sda1; I believe it originates from /tmp/mnt/sda1 but I can be wrong. I do not know how to point the path to /mnt/sda1.

Once you upgrade with no reset the message you get from NAS file sharing path:mnt/sda1(unavailable)

Also when you click on the share folder on the network from internet explorer in Windows 7 you get three (3) subfolders, sda1, sda5 and sda6; all empty. I believe they all originate from the Driver manager from /dev/sda1, /dev/sda5 and /dev/sda6

How many more upgrades before this is corrected. Nas is not working.
IONK
DD-WRT User


Joined: 19 Aug 2011
Posts: 219

PostPosted: Fri Feb 12, 2021 1:41    Post subject: Reply with quote
Router/Version: D-Link DIR-868L Rev.A1
File/Kernel: dir868a-webflash.bin / Linux 4.4.255 #2020 SMP Wed Feb 10 10:47:21 +06 2021 armv7l
Previous/Reset: DD-WRT v3.0-r45729 std (02/10/21) / no
Mode/Status: Repeater Bridge on 5GHz AC/N-Mixed (wl0 is purposely turned off) / working
Issues/Errors: none

Happy Lunar New Year!

_________________
▫ RSS feed for DD-WRT releases: https://feed43.com/ddwrt-downloads.xml (unofficial)
easyddup - A simple upgrade/downgrade utility by yoyoma2
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 7449
Location: Netherlands

PostPosted: Fri Feb 12, 2021 7:55    Post subject: Reply with quote
Abboo wrote:
Same problem as explained in build r45711. Reverted back to build r45592

Extract from build r45711
My diagnosis of the NAS problem: the file sharing path is /mnt; there should also be this path which is in the older builds, /mnt/sda1; I believe it originates from /tmp/mnt/sda1 but I can be wrong. I do not know how to point the path to /mnt/sda1.

Once you upgrade with no reset the message you get from NAS file sharing path:mnt/sda1(unavailable)

Also when you click on the share folder on the network from internet explorer in Windows 7 you get three (3) subfolders, sda1, sda5 and sda6; all empty. I believe they all originate from the Driver manager from /dev/sda1, /dev/sda5 and /dev/sda6

How many more upgrades before this is corrected. Nas is not working.


@Abboo the path you should mount a partition is indeed /mnt/sdax (or /mt/sdbx if you have also a second USB port) or even /opt or /jffs if you named the partititions like that and enable automatic drive mount

If you do not have it consider should reviewing your settings and/or reformatting the drive again, I have no problems with my R6400.

Are you using an ntfs partition?

_________________
Routers:Netgear R7800, R6400v1, R6400v2, Linksys EA8500, EA6900 (XvortexCFE), E2000 (converted WRT320N), WRT54GS v1.
WireGuard Documents & Guides:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327397
OpenVPN Documents & Guides: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327398
IPSET: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327261
Install guide R6400v2:http://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read):https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
Abboo
DD-WRT User


Joined: 03 Apr 2016
Posts: 170

PostPosted: Fri Feb 12, 2021 11:13    Post subject: Reply with quote
egc wrote:
Abboo wrote:
Same problem as explained in build r45711. Reverted back to build r45592

Extract from build r45711
My diagnosis of the NAS problem: the file sharing path is /mnt; there should also be this path which is in the older builds, /mnt/sda1; I believe it originates from /tmp/mnt/sda1 but I can be wrong. I do not know how to point the path to /mnt/sda1.

Once you upgrade with no reset the message you get from NAS file sharing path:mnt/sda1(unavailable)

Also when you click on the share folder on the network from internet explorer in Windows 7 you get three (3) subfolders, sda1, sda5 and sda6; all empty. I believe they all originate from the Driver manager from /dev/sda1, /dev/sda5 and /dev/sda6

How many more upgrades before this is corrected. Nas is not working.


@Abboo the path you should mount a partition is indeed /mnt/sdax (or /mt/sdbx if you have also a second USB port) or even /opt or /jffs if you named the partititions like that and enable automatic drive mount

If you do not have it consider should reviewing your settings and/or reformatting the drive again, I have no problems with my R6400.

Are you using an ntfs partition?


I am using ntfs partition.
Automatic drive mount is always enabled in usb.
My nas problem arose after build 45592 and they all say the same thing: /mnt/sda1(unavailable)
I performed a reset and manually rekeyed all data until I got to nas to discover the required path is not there and I cannot key in the path
Even though you are enjoying success with your router and nas, I have netgear r8000 with experimental drivers, I do not know if that can be a factor
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 7449
Location: Netherlands

PostPosted: Fri Feb 12, 2021 11:34    Post subject: Reply with quote
I think experimental refers to the wireless drivers.

What changed is the ntfs driver.

Of course it is possible that in your particular router something goes wrong in building/compiling.
You can check if in /lib/modules/(xxx.xx.xx) ntfs.ko is present.

The router should check what format is present on the usb stick and then load the necessary kernel module.

If the router does not know the format it can not load the module.

Things to try:
insmod ntfs.ko manually
Reformat the usb drive, I use minitool partition wizard or gparted.

Question:
Is this a non default drive, i.e. more than one partition, or very large etc. ?

_________________
Routers:Netgear R7800, R6400v1, R6400v2, Linksys EA8500, EA6900 (XvortexCFE), E2000 (converted WRT320N), WRT54GS v1.
WireGuard Documents & Guides:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327397
OpenVPN Documents & Guides: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327398
IPSET: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327261
Install guide R6400v2:http://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read):https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
saphirely
DD-WRT Novice


Joined: 13 Dec 2020
Posts: 28

PostPosted: Fri Feb 12, 2021 14:07    Post subject: Reply with quote
Router/Version: Netgear R6250 v1
Firmware: DD-WRT v3.0-r45735 std (02/11/21)
Kernel: Linux 4.4.255 #2020 SMP Wed Feb 10 10:47:21 +06 2021 armv7l
Mode: Gateway, Wireless AP
Reset: No
Previous:r45729

Upgrade: Web and 1st succeed without reset.
Load Average 0.08, 0.01, 0.01
Temperatures CPU 75.8 °C (max 79) / WL0 48.9 °C / WL1 55.7 °C

Uptime 1day

DHCP Server: Enabled - Running (no need to dial-up like DSL, it is cable connection after modem)
Disable (Samba, WRT-radauth, WRT-rflow, MAC-upd,CIFS Automount, Sputnik Agent)

Schedule of switch off function is back to normal.
Dual WiFi are normal working.
Abboo
DD-WRT User


Joined: 03 Apr 2016
Posts: 170

PostPosted: Fri Feb 12, 2021 14:25    Post subject: Reply with quote
egc wrote:
I think experimental refers to the wireless drivers.

What changed is the ntfs driver.

Of course it is possible that in your particular router something goes wrong in building/compiling.
You can check if in /lib/modules/(xxx.xx.xx) ntfs.ko is present.

The router should check what format is present on the usb stick and then load the necessary kernel module.

If the router does not know the format it can not load the module.

Things to try:
insmod ntfs.ko manually
Reformat the usb drive, I use minitool partition wizard or gparted.

Question:
Is this a non default drive, i.e. more than one partition, or very large etc. ?


The size of my partition:
-- /dev/sda1
Block device, size 1.818 TiB (1999321956352 bytes)
Windows BOOTMGR boot loader
NTFS file system
UUID 01D4DDF8D599C780
Volume size 1.818 TiB (1999321952256 bytes, 3904925688 sectors)
/dev/sda1 mounted to /tmp/mnt/sda1

The above information was copied from build 445592

I also have /opt and /jffs

As to checking if in /lib/modules/(xxx.xx.xx) ntfs.ko is present and
insmod ntfs.ko manually
How to do these? I am a novice trying to learn a thing or two.
I initially formatted by usb drive using minitool partition wizard
canmanxl
DD-WRT User


Joined: 02 Feb 2017
Posts: 56

PostPosted: Fri Feb 12, 2021 15:47    Post subject: Drive issues as well Reply with quote
Firmware:45729
Router: Netgear R8500

I have been having drive issues as well for a few builds now. I tried the firmware listed in abboo listed 45592 and I still have the issue. I will need to go farther back to see where this issue started.
turbowells
DD-WRT User


Joined: 14 Sep 2019
Posts: 201
Location: Maine, USA

PostPosted: Fri Feb 12, 2021 17:10    Post subject: Reply with quote
Router/Version: Asus RT-N66U
File: dd-wrt.v24-45735_NEWD-2_K3.x_mega_RT-N66U.trx
Firmware: DD-WRT v3.0-r45735 mega (02/11/21)
Kernel: Linux 4.4.255 #6809 Thu Feb 11 18:50:00 +06 2021 mips
Mode: Gateway/USB/bwmon
Previous: r45667
Reset?: N
Status: Working

Router/Version: Linksys E3200
File: dd-wrt.v24-45735_NEWD-2_K3.x_mega-e3200.bin
Firmware: DD-WRT v3.0-r45735 mega (02/11/21)
Kernel: Linux 4.4.255 #6809 Thu Feb 11 18:50:00 +06 2021 mips
Mode: Guest Gateway/QOS
Previous: r45667
Reset?: N
Status: Working
Abboo
DD-WRT User


Joined: 03 Apr 2016
Posts: 170

PostPosted: Fri Feb 12, 2021 18:48    Post subject: Reply with quote
Abboo wrote:
egc wrote:
I think experimental refers to the wireless drivers.

What changed is the ntfs driver.

Of course it is possible that in your particular router something goes wrong in building/compiling.
You can check if in /lib/modules/(xxx.xx.xx) ntfs.ko is present.

The router should check what format is present on the usb stick and then load the necessary kernel module.

If the router does not know the format it can not load the module.

Things to try:
insmod ntfs.ko manually
Reformat the usb drive, I use minitool partition wizard or gparted.

Question:
Is this a non default drive, i.e. more than one partition, or very large etc. ?


The size of my partition:
-- /dev/sda1
Block device, size 1.818 TiB (1999321956352 bytes)
Windows BOOTMGR boot loader
NTFS file system
UUID 01D4DDF8D599C780
Volume size 1.818 TiB (1999321952256 bytes, 3904925688 sectors)
/dev/sda1 mounted to /tmp/mnt/sda1

The above information was copied from build 445592

I also have /opt and /jffs

As to checking if in /lib/modules/(xxx.xx.xx) ntfs.ko is present and
insmod ntfs.ko manually
How to do these? I am a novice trying to learn a thing or two.
I initially formatted by usb drive using minitool partition wizard


I was able to find /lib/modules/(xxx.xx.xx) ntfs3.ko in the build 45735 having loaded it.
As to insmod ntfs.ko manually, I do not understand it. As in build r45592, it says in the usb section: /dev/sda1 mounted to /tmp/mnt/sda1
But in the NAS section it says: /mnt/sda1(unavailable)
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 7449
Location: Netherlands

PostPosted: Fri Feb 12, 2021 18:55    Post subject: Reply with quote
Well you could always file a bug report in the bug tracker: https://svn.dd-wrt.com

It maybe has something to do with the size of the drive or the way this drive is partitioned (but of course it should not be)

_________________
Routers:Netgear R7800, R6400v1, R6400v2, Linksys EA8500, EA6900 (XvortexCFE), E2000 (converted WRT320N), WRT54GS v1.
WireGuard Documents & Guides:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327397
OpenVPN Documents & Guides: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327398
IPSET: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=327261
Install guide R6400v2:http://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read):https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 8415
Location: Texas, USA

PostPosted: Fri Feb 12, 2021 19:05    Post subject: Reply with quote
Or, it could be, as I have hesitated to say for at least a week, if not two, that it's a problem with using *gasp* Win7 still.
_________________
Official Forum Rules, Guidelines & Helpful InformationFirmware FAQInstallation WikiWhere Do I Download Firmware?
DON'T use Chromium-based browsersRTFM/STFW TL;DR is NOT an excuse. • Why Should I Care What Color the Bikeshed Is?
Please DO NOT PM me with questions; Ask in the forum. ---------------------- Linux User #377467 counter.li.org / linuxcounter.net
Goto page 1, 2, 3  Next Display posts from previous:    Page 1 of 3
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum