Joined: 08 May 2018 Posts: 9027 Location: Texas, USA
Posted: Thu Feb 11, 2021 15:25 Post subject: New Build - 02/11/2021 - r45735
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specific recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
• There may be remaining issues for Samba.
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Linksys EA8500... main router
DD-WRT v3.0-r45735 std (02/11/21)
Linux 4.9.255 #1121 SMP Thu Feb 11 00:51:24 +07 2021 armv7l
GUI install over r44786 using Version 88.0.4324.146 (Developer Build) built on Debian bullseye/sid, running on Debian bullseye/sid (64-bit)
took 2.4 off NG-Mixed & set to mixed before install so we'll see how it does
working so far
Netgear WNDR3700 V4
DD-WRT v3.0-r45735 std (02/11/21)
Linux 3.18.140-d5 #106500 Thu Feb 11 07:47:43 +06 2021 mips
GUI install over r45667
all worky for what this unit does
Router/Version: Netgear X4S R7800.
File/Kernel: r45735 std, Linux 4.9.255 #1123.
Previous/Reset: Netgear v18.104.22.168 (current for R7800), reset to Netgear factory defaults before installing *.img file via Netgear web GUI.
Mode/Status: In service 6+ hours, Ethernet, 2.4GHz, 5GHz, good speed, low error rate.
Issues/Errors: None I'm aware of.
Thank you for builds and wealth of instructions.
pointless commit r45727 ruining ng-mixed, make sure to override it manually...
(on the other hand.. fixed my qca9888 crash issue finally)
I started a new post, I discovered that on same build on my R7800, and brand new toy the R9000, if I have the exact same settings and have 5ghz set for AC/N Mixed my devices can see the 5ghz of the R9000 but not the R7800. Only way to have the 5GHZ show up for R7800 is change to mixed.
Joined: 05 Oct 2008 Posts: 418 Location: Helsinki, Finland
Posted: Sat Feb 13, 2021 10:53 Post subject:
R7800 upgraded via GUI without reset.
Thumb drive with two ext4 partitions - JFFS and Optware - attached to USB port get mounted and are accessible by router (dnsmasq.leases & reserved IP file) and my Linux Mint laptop client via SMB (latest version 3.11 for min & max).
2.4 (NG-mixed) & 5 GHz (AC/N-mixed) WLAN OK. 5 GHz speeds up to 433 Mbps as per the gui.
LAN Active client stats look generally ok, but it's hard to verify whether the numbers are correct.
However ... my laptop is sometimes listed with two IP's, one being the reserved IP and the other 169.xxx.xxx.xxx (always the same one). In such case, the # of connections is erroneously shown as 0, but the in/out/totals are going up over time and the connections table does show numerous connections, which is as expected.
UPDATE: in this case - two IP's - the hostname is not shown in the Active Clients list.
Indeed, according to the DNS server's network list the laptop has two different names, the one for 169.xxx.xxx.xxx given as <hostname>.local, whereas the name for the reserved IP is listed as <hostname>.<local domain name>
Whenever the laptop is shown with only its reserved IP after it, the # of connections is non-zero and looks reasonable.
Local clients that use Wireguard VPN (running on a raspberry pi which runs the DNS server, too) sometimes show zero connections, sometimes one (to the WAN IP). Some low traffic totals, but not likely everything (it's a smartphone, chattering or attempting to chatter incessantly)
Previous/Reset: dd-wrt-webupgrade-netgear_r7800-r44772.bin / no reset
Mode/Status: WDS AP with 4 stations / Working
Issues/Errors: wireguard rate dropped from 320 Mb to 160 Mb - reboot did not fix the problem
Feb 13 11:03:27 r7800master user.err wsdd2: error: llmnr-tcp-v6: open_ep: SO_BINDTODEVICE
Feb 13 11:03:28 r7800master daemon.info mstpd: error, CTL_set_cist_bridge_config: Couldn't find bridge with index 19
Feb 13 11:03:28 r7800master user.err wsdd2: error: wsdd-mcast-v4: wsd_send_soap_msg: send