Your reports for Broadcom units are highly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29621_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.
Router: Netgear WNDR4000
Mode: 2.4GHz CB to wired + 5GHz AP
Firmware: DD-WRT v3.0-r30949 mega (12/15/16)
Kernel: Linux 3.10.104 #14923 Thu Dec 15 13:48:53 CET 2016 mips
Previous: 29495 K3x
Reset: No
Uptime/Status: Used it for 30min, working fine so far.
===========================================
Router: Netgear WNDR4500v2
Mode: 2.4GHz CB to wired + 5GHz AP
Firmware: 30949
Kernel: Linux 3.10.104
Previous: 30826
Reset: No
Uptime/Status: Changed this from an AP (plus non-working guest network) to a CB+AP; worked fine for 30min.
I'm curious to try a build with 30950 at my parents' house and their cellular service. I now no longer have any DD routers in normal service except the ol' WRT54GL & GS at the in-laws still on 27858. _________________ #NAT/SFE/CTF: limited speed w/ DD#Repeater issues#DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo#
OPNsense x64 5050e ITX|DD: DIR-810L, 2*EA6900@1GHz, R6300v1, RT-N66U@663, WNDR4000@533, E1500@353,
WRT54G{Lv1.1,Sv6}@250|FreshTomato: F7D8302@532|OpenWRT: F9K1119v1, RT-ACRH13, R6220, WNDR3700v4
Router: Asus RT-AC66U
Firmware: DD-WRT v3.0-r30949 giga (12/15/16)
Previous: DD-WRT v3.0-r30805 giga (10/27/16)
Kernel: Linux 3.10.104 #14907 Thu Dec 15 13:34:55 CET 2016 mips
Status: OpenVPN Server does not start, all other functions nominal.
Reset: YES via GUI
Errors: OpenVPN Server 2.4_rc1 command line errors
See below for previously working Services->VPN configuration.
See attached file openvpn.conf.txt for generated /tmp/openvpn/openvpn.conf
See attached file openvpn.msgs.txt for relevant /var/log/messages
See attached file openvpn.status.txt for contents of Status->OpenVPN
OpenVPN Server/Daemon config:
Code:
OpenVPN (o) Enabled
Start Type (o) WAN Up
Config as (o) Server
Server mode (o) Router(TUN)
Network REDACTED
Netmask 255.255.255.0
Port 1194
Tunnel Protocol UDP
Encryption Ciph AES-256 CBC
Hash Algorithm SHA256
Advanced Opt. (o) Enable
TLS Cypher TLS-DHE-RSA-WITH-AES-256-CBC-SHA256
LZO Compression Yes
Redirect dflt G (o) Enable
Allow Cli 2 Cli (o) Enable
Allow dup cn (o) Enable
Tun MTU setting 1500
Tun UDP Frag empty
Tun UDP MSS-Fix (o) Enable
Additional Config
tls-version-min 1.2
server-ipv6 REDACTED::/64
IPv6 DHCPv6 PD: OK
WAN/LAN ports: OK
2.4GHz 40MHz N AP: OK
5GHz 40MHz AC/N AP: OK
ISP 30/6 Bandwidth: 29.52/5.63 IPv4, 29.73/5.98 IPv6
Site Survey: OK
Wiviz Survey: OK
OpenVPN Server: Command line errors shown in /var/log/messages
USB Flash Drive: OK mounting /opt, /jffs, /swap partitions
Privoxy + Easylist: OK on /jffs
CPU Temperature: WL0 51.5 °C / WL1 56.0 °C
Asus Rt-ac5300 updated from stock firmware. The lan ports still do not work. Installed Kongs ac5300 12 2 2016 fw and lan ports are back. _________________ Please Fix The Following Bugs:
EOIP Settings not applied automatically after FW upgrade or reboot. http://svn.dd-wrt.com/ticket/4061
The port 80 forwarding bug with out reapplying settings appears to have been fixxed.
Router: Linksys EA6400
Firmware: DD-WRT v3.0-r30949 std (12/15/16)
Kernel: Linux 4.4.39-rc1 #1615 SMP Wed Dec 14 16:57:09 CET 2016 armv7l
Status: Working fine so far.
Reset: Yes
Errors: No
Router: RT-AC87U - primary router/gateway
Firmware Version: DD-WRT v3.0-r30949 std (12/15/16)
Kernel Version: Linux 4.4.39-rc1 #1622 SMP Thu Dec 15 09:44:23 CET 2016 armv7l
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (AC/N-Mixed) with 80Mhz channel width: OK
Guest-Vlan 2.4Ghz: OK
SSH: OK
Telnet: OK
Port Forward: OK
WOL over the Internet: OK
VNC Repeater: OK
USB 2.0 storage ext3 mount to JFFS: OK
USB 3.0 storage NTFS mount to MNT: OK
NAS Samba shared drive: OK
PPTP Server: OK
Wi-viz 2.4Ghz & 5Ghz: 2.4Ghz OK – 5Ghz NO
Reset via GUI: Yes before and after upgrade
Status: Working
Error(s): Guest network does not show any output signal, noise, or SNR in the wireless client’s output table
5Ghz - Explicit Beamforming and Implicit Beamforming changes are not saved
Repeater Bridge Build 30949 previous build 30796
Router: RT-AC66U - Repeater Bridge on 5 Ghz (AC-Only) to RT-AC87U
Firmware Version: DD-WRT v3.0-r30949 giga (12/15/16)
Kernel Version: Linux 3.10.104 #14907 Thu Dec 15 13:34:55 CET 2016 mips
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (AC-Only): OK
Reset via GUI: NO
Status: Working
Error(s): OK _________________ Netgear XR500, R7800
Asus AC87Ua1
Repeater Bridge
Netgear R6400v2otp
Joined: 04 Jan 2007 Posts: 11564 Location: Wherever the wind blows- North America
Posted: Fri Dec 16, 2016 14:21 Post subject:
The old broadcom v24 build of mega is reported as build 30905 not 30949 on my old WL-500W. It happens from time to time...BS misses something with this mega build and it doesn't display the correct build number.
Other than that...no issues.
redhawk _________________ The only stupid question....is the unasked one.
Router: R8500 Made in Vietnam ver
Firmware: r30949
Previous: 1.0.2.80_1.0.71 (OEM)
Kernel:
Status: Update Failed
Reset:
Errors: Firmware not compatible -2
There seems to be a new group of R8500s with a new sig that do not see any DD-WRT builds as compatible. From looking at the few instances where this has cropped up, it seems that Made in China models flash no problem but Made in Vietnam models don't.
Router: D-Link 868L RevA1
Firmware: 12-15-2016-r30949
Status: Brick, bootloop. Recovery from 192.168.0.1. Revert to r30432 (08/16/16). _________________ Anger Is A Gift
RAGE AGAINST THE MACHINE
Router: WRT1900ACS
Firmware: DD-WRT v3.0-r30949 std (12/15/16)
Kernel: Linux wrt1900acs 3.18.45 #106 SMP Mon Dec 12 23:05:56 CET 2016 armv7l DD-WRT
Status: mostly working
Reset: yes
Errors: OpenVPN server won't start
Only log entry from /var/log/messages for openvpn: Dec 16 23:12:15 wrt1900acs daemon.warn openvpn[4247]: Note: option tun-ipv6 is ignored because modern operating systems do not need special IPv6 tun handling anymore.