[blkt]

[chromoxdor]

Router/Version: D-Link DIR-868L Rev.B1
File/Kernel: dir868b-webflash.bin / Linux 4.4.249 #1760 SMP Fri Jan 8 12:08:02 +07 2021 armv7l
Previous/Reset: original FW / yes
Mode/Status: Repeater on 5GHz AC/N-Mixed; wl0 AP; wl1.1 VAP
Issues/Errors: on every reboot i loose the ability to connect to the 5ghz vap. i get asked for the password but after typing it it still won’t connect. another reboot doesn’t help.
workaround: change a setting for the vap every time this happens. (eg. changing security algortithm from aes to tkip+aes then apply)

EDIT: oh ohh.... i should read more carefully. it´s a known problem but nevertheless the workarounds with the suggested startupscripts (tried several)do not work...unfortunately

[hurleyp]

Firmware: v3.0-r45385 std (01/09/21)
Router/Version: Netgear R7000
Kernel: Linux 4.4.249 #1760 SMP Fri Jan 8 12:08:02 +07 2021 armv7l
Previous: v3.0-r45229 std (01/01/21)
Mode/Status: AP wired and wireless, Up and running for 2 days
Reset: Soft boot before and after upgrade
Temperatures: CPU 58.0 °C / WL0 45.0 °C / WL1 50.2 °C
Issues/Errors: Nothing significant

Updated via webif. No 'nvram erase' this time, last one was in July 2018 (r36325).

There is a minor issue with the packet count on wl0.1 and "Connected Clients" stuck at zero. The wl0 and wl1 counts seem correct.
Upload and Download speeds are to ISP spec. Nothing unexpected in the syslog. GRC port probe shows "TruStealth".

Current basic R7000 setup (subject to change of course):
- Static WAN IP
- SFE - On
- STP - On
- IPv4 only, both WAN and LAN
- LAN DHCP Enabled
- Wireless: AP, Regulatory Domain = CANADA, wl0 Mixed (ch. 6), wl1 AC/N-Mixed (ch. 149, VHT80), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- No custom scripts
- NO: ttraf, Tor, VNC, Zabbix, VPN, Radius, OpenVPN
- NO: UPnP, DMZ, QoS
- NO: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware

[Welshchris]

[blkt]

Look inside those folders; you can see they are for different older router models with limited flash memory.

[thommy181]

Router: Netgear WNR3500L v2
Kernel: Linux 4.4.249 #6103 Sat Jan 9 17:23:07 +07 2021 mips
Reset: No
Mode: Internet gateway, WIFI AP, Dnsmasq server
Errors: eth0 interface haven't new MAC. I'm put MAC via GUI. Router have original MAC on eth0. On other interface I can change MAC
Status: Working
Uptime: more than 31h

Device have a problem with catch new mac for eth0 interface. I have new MAC saved via GUI. When I'm type ifconfig command eth have original MAC still. In my network I need my own MAC. Other interfaces give new MAC correct. Generally router working rather good. That's small problem is for fix in my opinion.

[Abboo]

Router Model: Netgear R8000
Firmware Version: DD-WRT v3.0-r45385 std (01/09/21)
Kernel Version: Linux 4.4.249 #1768 SMP Sat Jan 9 11:47:09 +07 2021 armv7l
Previous Version: DD-WRT v3.0-r45229 std (01/01/21)
Drivers: Experimental
Services: samba, wireguard client, openvpn client, dhcp, wifi 2.4 ghz, usb, nas
Status: working
Updated: via webgui
Mode: AP/gateway
Issues: none
Reset: no
Uptime: 4 days, 22:43
Errors: as reported in the syslog below


Jan 14 19:01:34 DD-WRT daemon.err httpd[1414]: httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases