Joined: 08 May 2018 Posts: 14221 Location: Texas, USA
Posted: Tue Dec 15, 2020 4:08 Post subject: New Build - 12-14-2020-r45000
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and specific device recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• DNScrypt 1.95 can still be used in the GUI but v2 (not compatible) requires Golang and thus Entware. 6246
• WDS does not work on Broadcom ARM devices(only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work in some configurations in certain builds but are not supported by the bcmdhd driver. Use client or repeater instead.
• VAPs not working at bootfixed for unbridged VAPs with r40564:40566.Workaround startup command:
sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas(there are a few alternatives, search).
• If start-up scripts do not work from USB add a delay (e.g. wait script or 'sleep 25').
• For Broadcom ARM devices missing 5GHz channels, via telnet/ssh: 'nvram set brcm_unlock=1' 'nvram commit' 'nvram reboot'
Important:
• If reporting issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, serial output, strace, tcpdump etc.
• For firewall NAT or WAN issues provide 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and the /tmp/.ipt file.
• Search existing SVN tickets before opening a new one. Before reporting, reset and manually setup (no nvram backup).
• Be sure to include operating and wireless modes (Gateway, AP, CB, etc.) along with relevant configuration information.
Joined: 26 Mar 2013 Posts: 1857 Location: Hung Hom, Hong Kong
Posted: Tue Dec 15, 2020 8:36 Post subject:
Router/Version:Asus RT-N18U (rev. A1)
Firmware: DD-WRT v3.0-r45000 std (12/14/20)
Kernel: Linux 4.4.248 #1566 Mon Dec 14 09:35:02 +07 2020 armv7l
Previous: DD-WRT v3.0-r44970 std (12/11/20)
Mode: WAN @ DHCP, Wireless @ AP
Status: Working (Not 24/7; Not using IPv6, VAP, VPN; Using NAS & USB; Unbound enabled)
Reset: NO reset during firmware upgrade but cold boot
Quick&Dirty Report
Working in Asus RT-N18U! WAN OK, Wifi OK, Samba OK, Unbound OK, MiniDLNA seemed OK, ....
May I suggest adding a zero-byte file "/tmp/smb.db" to calm that ksmbd error message during startup?
Formal report: later, after cold boot!
Side-note:
Mozilla VPN!? I didn't know about it though it's old news.
Firefox updated to version 84.
Update:
Since there are new builds, I gave up posting a "formal" report for build 45000!
Happy Year 2021!!!! _________________ Router: Asus RT-N18U (rev. A1)
Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!
Firmware Version: DD-WRT v3.0-r45000 Community Build (12/15/20)
Kernel Version: Linux 4.4.248 #1 SMP Tue Dec 15 08:04:57 CET 2020 armv7l
Upgraded from: DD-WRT v3.0-r44980 std (12/12/20)
Reset: No not this time
Status: Up and running for 4 hours, basic setup as Gateway, static leases, OpenVPN client with Policy Based Routing up and running, 2,4GHz and 5Ghz with excellent range and speed, USB storage NAS working, OpenVPN server working, WireGuard server working with 8 clients (phones , windows and two other routers for site-to-site setup).
Joined: 18 Mar 2014 Posts: 12884 Location: Netherlands
Posted: Tue Dec 15, 2020 12:25 Post subject:
Router Model: Linksys E2000 (converted N320)
Firmware Version: DD-WRT v3.0-r45000 mega (12/14/20)
Kernel Version: Linux 4.4.248 #5389 Mon Dec 14 15:33:55 +07 2020 mips
Upgraded: from DD-WRT v3.0-r44980 mega (12/12/20)
Reset: No, not this time
Status: Up and running for 2 hours, basic setup as Gateway, static leases, OpenVPN client working, VPN download speed 5-6 Mb/s, Wifi 2,4GHz working.
WireGuard client working (do not forget to set the IPaddres/netmask of tunnel) speed around 18 Mb/s
Joined: 29 Sep 2020 Posts: 260 Location: United States
Posted: Tue Dec 15, 2020 12:46 Post subject:
Router/Version: Netgear R7000P
File/Kernel: netgear-r7000p-webflash.bin / Linux 4.4.248 #1568 SMP Mon Dec 14 09:48:27 +07 2020 armv7l
Previous/Reset: r44980 / no
Mode/Status: Gateway AP 2.4 GHz & 5 GHz Unbound USB / working
Issues/Errors: 'nvram set brcm_unlock=1' 'nvram commit' 'reboot' and changing Regulatory Domains does not resolve the no low 5 GHz channels on this router. an open ticket about the issue https://svn.dd-wrt.com/ticket/7023
otherwise seems to be good
Last edited by itwontbewe on Wed Jan 13, 2021 18:23; edited 3 times in total
Router/Version: Asus RT-AC68U rev C1
Firmware: DD-WRT v3.0-r45000 std (12/14/20)
Kernel: Linux 4.4.248 #1562 SMP Mon Dec 14 09:12:35 +07 2020 armv7l
Previous: r44970
Reset: Yes, full reset to factory defaults
Mode/Status: Gateway AP/ OK
Issues/Errors: Flashed using CLI from 44970. Seemed to work well until I power cycled, then lost all functionality. Had to reset and setup from scratch (fortunately I have a file with all settings). _________________ Netgear R7000 on Build 55109
Asus AC-AC68U rev. C1 (AP) on Build 55109
Asus AC-68U rev. A1 on Build 54604
Asus AC-68U rev. A1 on Build 53339
Router Model: Netgear R7000
Firmware Version: DD-WRT v3.0-r45000 std (12/14/20)
Kernel Version: Linux 4.4.248 #1562 SMP Mon Dec 14 09:12:35 +07 2020 armv7l
Upgraded from: DD-WRT v3.0-r44863 std
Reset: No
Used as Gateway, static DHCP leases, 5Ghz Wifi, USB storage with NAS working (Samba v2)
Status: Running well
Errors: CPU %usage in the status page seems to be based on load now. With a load factor of 1.8, CPU% is calculated to be 90%. This is misleading/incorrect, top reports both CPUs about 80% idle when status page is showing 100% used.
Firmware: v3.0-r45000 std (12/14/20)
Router/Version: Netgear R7000 Kernel: Linux 4.4.248 #1562 SMP Mon Dec 14 09:12:35 +07 2020 armv7l
Previous: v3.0-r44970 std (12/11/20)
Mode/Status: AP wired and wireless, Up and running for 1 day
Reset: Soft boot before and after upgrade
Temperatures: CPU 56.9 °C / WL0 44.6 °C / WL1 49.6 °C
Issues/Errors: Nothing significant
Updated via webif. No 'nvram erase' this time, last one was in July 2018 (r36325).
There is a minor issue with the packet count on wl0.1 and "Connected Clients" stuck at zero. The wl0 and wl1 counts seem correct.
Upload and Download speeds are good. Nothing unexpected in the syslog. GRC port probe shows "TruStealth".
Current basic R7000 setup (subject to change of course):
- Static WAN IP
- SFE - On
- STP - On
- IPv4 only, both WAN and LAN
- LAN DHCP Enabled
- Wireless: AP, Regulatory Domain = CANADA, wl0 Mixed (ch. 6), wl1 AC/N-Mixed (ch. 149, VHT80), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- No custom scripts
- NO: ttraf, Tor, VNC, Zabbix, VPN, Radius, OpenVPN
- NO: UPnP, DMZ, QoS
- NO: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7
Router Model: Netgear R8000
Firmware Version: DD-WRT v3.0-r45000 std (12/14/20)
Kernel Version: Linux 4.4.248 #1570 SMP Mon Dec 14 09:59:25 +07 2020 armv7l
Previous Version: DD-WRT v3.0-r44980 std (12/12/20)
Drivers: Experimental
Services: samba, wireguard client, openvpn client, dhcp, wifi 2.4 ghz, usb, nas
Status: working
Updated: via webgui
Mode: AP/gateway
Issues: none
Reset: no
Uptime: 2 days, 13:55
Errors: as reported in the syslog below
Dec 31 20:00:19 DD-WRT user.err wsdd2[1211]: error: wsdd-mcast-v4: wsd_send_soap_msg: send
Dec 31 20:00:19 DD-WRT local5.err ksmbd: [ksmbd-manager/1225]: ERROR: Can't open `/tmp/ksmbd.subauth': No such file or directory
Dec 31 20:00:19 DD-WRT local5.err ksmbd: [ksmbd-worker/1226]: ERROR: Can't open `/tmp/smb.db': No such file or directory
Dec 31 20:00:19 DD-WRT local5.err ksmbd: [ksmbd-worker/1226]: ERROR: User database file does not exist. Only guest sessions (if permitted) will work.
Dec 15 07:49:46 DD-WRT user.err wsdd2[1211]: Terminated received.
Dec 15 07:49:46 DD-WRT local5.err ksmbd: [ksmbd-manager/1225]: ERROR: WARNING: child process exited abnormally: 1226
Dec 15 07:49:48 DD-WRT local5.err ksmbd: [ksmbd-worker/2046]: ERROR: Can't open `/tmp/smb.db': No such file or directory
Dec 15 07:49:48 DD-WRT local5.err ksmbd: [ksmbd-worker/2046]: ERROR: User database file does not exist. Only guest sessions (if permitted) will work.
Dec 15 07:49:50 DD-WRT local5.err ksmbd: [ksmbd-manager/2283]: ERROR: Failed to create lock file: File exists
Dec 17 21:29:56 DD-WRT daemon.err httpd[1316]: httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
Dec 17 21:41:22 DD-WRT daemon.err httpd[1316]: httpd : Request Error Code 408: No request appeared within a reasonable time period.
