Posted: Sun Aug 30, 2020 23:59 Post subject: Privoxy is not working from version r44213
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r44251 std (08/27/20)
Kernel: Linux 4.4.233 #935 Thu Aug 27 17:37:20 +04 2020 armv7l
Mode: Gateway
Previous: r44236
Reset: No
Status: Privoxy is not working from version r44213.
If Privoxy is enabled, can't access outside websites. Connections will just time out. Can't ping outside world. But DNS resolver works. I have to disable Privoxy to work around for now. Hope you guys can solve it in next version. Also Netgear R8000 had the same issue.
Status->LAN page in administration panel takes a very long time (3-6 seconds) to generate/refresh (on DLink DIR-880L, at least)
Eventually - it does produce a proper page with a valid info.
Dunno if the software behind it is working as intended, it might be worth checking out.
I've checked every other tab/subsection and everything else seems to be working fine in that regard.
Firmware: v3.0-r44251 std (08/27/20)
Router/Version: Netgear R7000 Kernel: Linux 4.4.233 #931 SMP Thu Aug 27 08:11:22 +04 2020 armv7l
Previous: v3.0-r44191 std (08/15/20)
Mode/Status: AP wired and wireless, Up and running for 3 days
Reset: Soft boot before and after upgrade
Temperatures: CPU 60.2 °C / WL0 46.4 °C / WL1 51.5 °C
Issues/Errors: Nothing significant
Updated via webif. No 'nvram erase' this time, last one was in July 2018 (r36325).
There is a minor issue with the packet count on wl0.1 and "Connected Clients" stuck at zero. The wl0 and wl1 counts seem correct.
Upload and Download speeds are good. Nothing unexpected in the syslog. GRC port probe shows "stealth".
Current basic R7000 setup (subject to change of course):
- Static WAN IP
- SFE - On
- STP - On
- IPv4 only, both WAN and LAN
- LAN DHCP Enabled
- Wireless: AP, Regulatory Domain = CANADA, wl0 Mixed (ch. 6), wl1 AC/N-Mixed (ch. 149, VHT80), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- No custom scripts
- NO: ttraf, Tor, VNC, Zabbix, VPN, Radius
- NO: UPnP, DMZ, QoS
- NO: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7
Posted: Mon Aug 31, 2020 18:31 Post subject: Wireguard server public key missing after Upgrade to 44251
Firmware: v3.0-r44251 mega (08/27/20)
Router/Version: Linksys E4200 v1
Kernel: Linux version 4.4.233 (root@linux) (gcc version 10.1.0 (OpenWrt GCC 10.1.0 r13225-bc0288b768) ) #3488 Fri Aug 28 00:21:38 +04 2020
Previous: v3.0-r44236 mega(08/22/20)
Mode: Wireless - AP, Wireguard Server
Issues/Errors: After upgrage (no reset, just reboot) the Wireguard Server public key is gone. The Server private key is set to some "random" key. The private key is not identical to the the previously used key on the previous build. As with the build before, the "=" signs at the end of all keys are missing. On the webinterface you cannot insert the old server key into the empty box. Thus, you cannot recreate the old settings and all client configurations have to be renewed.
Joined: 18 Mar 2014 Posts: 12915 Location: Netherlands
Posted: Tue Sep 01, 2020 7:58 Post subject:
Router Model: Linksys E2000 (converted N320)
Firmware Version: DD-WRT v3.0-r44251 mega (08/28/20)
Kernel Version: Linux 4.4.233 #3488 Fri Aug 28 00:21:38 +04 2020 mips
Upgraded: from DD-WRT v3.0-r44187 mega (08/13/20)
Reset: No, not this time
Status: Up and running for 24 hours, basic setup as Gateway, static leases, OpenVPN client (tun) (on PIA) up and running, VPN download speed 5-6 Mb/s, Wifi 2,4GHz working, WireGuard (server) working speed around 18 Mb/s
Firmware Version: DD-WRT v3.0-r44251M Community Build (08/31/20)
Kernel Version: Linux 4.4.234 #1 SMP Mon Aug 31 18:50:19 CEST 2020 armv7l
Upgraded from: DD-WRT v3.0-r44213M Community Build (08/18/20)
Reset: No not this time
Status: Up and running for 24 hours, basic setup as Gateway, static leases, OpenVPN client (on PIA) with Policy Based Routing up and running, 2,4GHz and 5Ghz with excellent range and speed, USB storage NAS working, OpenVPN server and WireGuard working.
Router Model: Netgear R6300 (v1)
Firmware Version: dd-wrt.v24-44251_NEWD-2_K3.x_giga-R6300.bin
Kernel Version: Linux 4.4.233 #3472 Fri Aug 28 00:01:33 +04 2020 mips
Upgraded: from DD-WRT v3.0-r43078 giga (05/07/20)
Reset: No, some fresh UI options are 'undefinded'
Status: All WiFi up and running, wireguard site-site tunnel working
Joined: 18 Mar 2014 Posts: 12915 Location: Netherlands
Posted: Tue Sep 01, 2020 9:38 Post subject:
hellf wrote:
Router Model: Netgear R6300 (v1)
Firmware Version: dd-wrt.v24-44251_NEWD-2_K3.x_giga-R6300.bin
Kernel Version: Linux 4.4.233 #3472 Fri Aug 28 00:01:33 +04 2020 mips
Upgraded: from DD-WRT v3.0-r43078 giga (05/07/20)
Reset: No, some fresh UI options are 'undefinded'
Status: All WiFi up and running, wireguard site-site tunnel working
Posted: Tue Sep 01, 2020 9:53 Post subject: Re: Wireguard server public key missing after Upgrade to 442
NFear wrote:
Issues/Errors: After upgrage (no reset, just reboot) the Wireguard Server public key is gone. The Server private key is set to some "random" key. The private key is not identical to the the previously used key on the previous build. As with the build before, the "=" signs at the end of all keys are missing. On the webinterface you cannot insert the old server key into the empty box. Thus, you cannot recreate the old settings and all client configurations have to be renewed.
Strange! You mentioned something similar in the last build thread... I checked back then and now a few minutes ago:
All my DD-WRT Devices, sporting Wireguard have their "=" signs, no key was lost.
Whatever is happening on your end, it seems to accumulate into something worse.
Joined: 18 Mar 2014 Posts: 12915 Location: Netherlands
Posted: Tue Sep 01, 2020 10:03 Post subject:
Maybe failing flash ram or browser with extensions which garbles the field?
I can also not reproduce this error.
You can not set a public key, that is derived from the private key which is saved in flash ram in nvram variable oet1_private, if the private key is not valid a public key will not be calculated
I know it is really strange. Only WireGuard settings are affected. Everything else is unaltered. That is why I do not suspect a faulty NVRAM. I guess there would be a broader effect when your NVRAM dies...
As for the browser, I use Firefox 80 for config works on the E4200. But same effect with latest Chrome, Edge or Safari on iOS. The empty field cannot be populated.
Maybe It is really time for an NVRAM erase. I hope the E4200 does not die on this completely...
Joined: 02 Apr 2007 Posts: 14 Location: Richmond, CA
Posted: Tue Sep 01, 2020 16:07 Post subject:
Router/Version: Netgear r8000
Current Firmware: DD-WRT v3.0-r44251 std (08/27/20)
Kernel: Linux 4.4.233 #936 SMP Thu Aug 27 17:44:00 +04 2020 armv7l
File: netgear-r8000-webflash.bin
Previous: r43718 (07/09/20)
Reset: no
Mode/Status: gateway, 3rd radio disabled, up 15+ hrs ok
Issues/Errors: so far so good
r43718 worked great for about a couple months, but once school started and the number of video meetings doubled I started getting complaints about the wireless not working. Got "incorrect password" errors and could not connect to wireless network. So I'm trying the latest and greatest, and it seems to be working well so far.
Huge thanks to everybody who keeps this running and constantly improving!
r43718 worked great for about a couple months, but once school started and the number of video meetings doubled I started getting complaints about the wireless not working. Got "incorrect password" errors and could not connect to wireless network.
That sounds a lot like the errors I was getting with r43471 on my r8000. No real changes in load, but 3-4 weeks of uptime was enough to upset my commonly used 2.4Ghz radio.
Router/Version: TP-Link Archer C9 v1
File/Kernel: Linux 4.4.233 #933 SMP Thu Aug 27 17:30:49 +04 2020 armv7l
Previous/Reset: r44048/no
Mode/Status: Gateway/2.4GHz & 5GHz AP/Openvpn server/Wireguard server
Issues/Errors:
USB "Run-on-mount Script" (usb_runonmount) is not executed (hasn't - at least - since 42910)
Code:
Jan 1 01:00:07 archy kern.err kernel: nflash: found no supported devices
Jan 1 01:00:07 archy kern.err kernel: brcmnand: found no supported devices
Jan 1 01:00:07 archy daemon.info mstpd[650]: error, CTL_set_cist_bridge_config: Couldn't find bridge with index 8
Jan 1 01:00:07 archy daemon.info mstpd[650]: error, CTL_set_cist_bridge_config: Couldn't find bridge with index 8
Jan 1 01:00:07 archy daemon.info mstpd[650]: error, CTL_set_msti_bridge_config: Couldn't find bridge with index 8
Jan 1 01:00:08 archy daemon.info mstpd[650]: error, CTL_set_cist_bridge_config: Couldn't find bridge with index 8
Jan 1 01:00:08 archy daemon.info mstpd[650]: error, CTL_set_cist_bridge_config: Couldn't find bridge with index 8
Sep 5 15:11:55 archy kern.err kernel: hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
