Bricked WRT32X

Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Author Message
RedDragon23
DD-WRT Novice


Joined: 11 Aug 2020
Posts: 5

PostPosted: Tue Aug 11, 2020 16:59    Post subject: Bricked WRT32X Reply with quote
Hi,

I bought the Linksys WRT32X a few months ago, tried OpenWRT wasn't for me and now trying DD-WRT. I tried to install it as a upgrade, ballsed it up and now I can't access the 192.168.1.1 WEB GUI and I think it's just acting like a switch when WAN is plugged in. I've tried Serial connection with TFTP, but I can't seem to be able to type any commands in. I don't know what else to do...

Here's a dump of the boot sequence I managed to capture through the serial port.

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.180 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11063-85e04e9f46)) #0 SMP Sat May 16 18:32:20 2020
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Linksys WRT32X
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] random: get_random_bytes called from 0xc08008bc with crng_init=0
[ 0.000000] percpu: Embedded 11 pages/cpu s14860 r8192 d22004 u45056
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock6
[ 0.000000] Bootloader command line (ignored): console= root=/dev/mtdblock6
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 510944K/524288K available (6144K kernel code, 199K rwdata, 816K rodata, 1024K init, 233K bss, 13344K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0700000 (7136 kB)
[ 0.000000] .init : 0xc0800000 - 0xc0900000 (1024 kB)
[ 0.000000] .data : 0xc0900000 - 0xc0931d40 ( 200 kB)
[ 0.000000] .bss : 0xc0931d40 - 0xc096c198 ( 234 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000006] sched_clock: 64 bits at 933MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.000015] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x1ae5b571769, max_idle_ns: 881590513431 ns
[ 0.000026] Switching to timer-based delay loop, resolution 1ns
[ 0.000125] Ignoring duplicate/late registration of read_current_timer delay
[ 0.000130] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000246] Calibrating delay loop (skipped), value calculated using timer frequency.. 1866.00 BogoMIPS (lpj=9330000)
[ 0.000252] pid_max: default: 32768 minimum: 301
[ 0.000299] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000303] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000491] CPU: Testing write buffer coherency: ok
[ 0.000501] CPU0: Spectre v2: using BPIALL workaround
[ 0.000589] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.000683] Setting up static identity map for 0x100000 - 0x100060
[ 0.000741] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[ 0.000802] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.000839] Hierarchical SRCU implementation.
[ 0.000994] smp: Bringing up secondary CPUs ...
[ 0.001093] Booting CPU 1
[ 0.001230] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.001232] CPU1: Spectre v2: using BPIALL workaround
[ 0.001274] smp: Brought up 1 node, 2 CPUs
[ 0.001278] SMP: Total of 2 processors activated (3732.00 BogoMIPS).
[ 0.001281] CPU: All CPU(s) started in SVC mode.
[ 0.002521] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.002563] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.002569] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.002612] pinctrl core: initialized pinctrl subsystem
[ 0.002888] NET: Registered protocol family 16
[ 0.003416] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.003820] cpuidle: using governor ladder
[ 0.003929] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.003935] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.008994] reg-fixed-voltage usb3_1-vbus: could not find pctldev for node /soc/internal-regs/pinctrl@18000/usb3_1-vbus-pins, deferring probe
[ 0.009149] SCSI subsystem initialized
[ 0.009309] usbcore: registered new interface driver usbfs
[ 0.009333] usbcore: registered new interface driver hub
[ 0.009356] usbcore: registered new device driver usb
[ 0.009841] clocksource: Switched to clocksource arm_global_timer
[ 0.010214] NET: Registered protocol family 2
[ 0.010428] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.010449] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.010476] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.010507] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.010520] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.010576] NET: Registered protocol family 1
[ 0.011351] Crashlog allocated RAM at address 0x3f00000
[ 0.011405] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.012777] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.012785] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.013905] io scheduler noop registered
[ 0.013910] io scheduler deadline registered (default)
[ 0.014305] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 0.015164] mvebu-pcie soc:pcie: PCI host bridge to bus 0000:00
[ 0.015174] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 0.015178] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 0.015183] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.015334] PCI: bus0: Fast back to back transfers disabled
[ 0.015339] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.015345] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.015530] PCI: bus1: Fast back to back transfers disabled
[ 0.015755] PCI: bus2: Fast back to back transfers disabled
[ 0.015777] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe02fffff]
[ 0.015782] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0400000-0xe06fffff]
[ 0.015789] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe01fffff 64bit pref]
[ 0.015798] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0200000-0xe02fffff 64bit pref]
[ 0.015806] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.015812] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe02fffff]
[ 0.015818] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0400000-0xe05fffff 64bit pref]
[ 0.015828] pci 0000:02:00.0: BAR 2: assigned [mem 0xe0600000-0xe06fffff 64bit pref]
[ 0.015837] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 0.015842] pci 0000:00:02.0: bridge window [mem 0xe0400000-0xe06fffff]
[ 0.016039] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.080236] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.080343] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.140210] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.140350] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.140937] console [ttyS0] disabled
[ 0.161001] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 22, base_baud = 12500000) is a 16550A
[ 0.893410] console [ttyS0] enabled
[ 0.898193] loop: module loaded
[ 0.901621] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 0.910718] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 0.919847] scsi host0: ahci-mvebu
[ 0.923401] scsi host1: ahci-mvebu
[ 0.926872] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41
[ 0.934842] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 41
[ 0.943154] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device
[ 0.951059] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda
[ 0.957440] nand: Macronix MX30LF2G18AC
[ 0.961299] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.968904] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048
[ 0.976158] Bad block table found at page 131008, version 0x01
[ 0.982464] Bad block table found at page 130944, version 0x01
[ 0.988557] nand_read_bbt: bad block at 0x00000f280000
[ 0.993810] 10 fixed-partitions partitions found on MTD device pxa3xx_nand-0
[ 1.000895] Creating 10 MTD partitions on "pxa3xx_nand-0":
[ 1.006404] 0x000000000000-0x000000200000 : "u-boot"
[ 1.011609] 0x000000200000-0x000000220000 : "u_env"
[ 1.016673] 0x000000220000-0x000000260000 : "s_env"
[ 1.021729] 0x000000260000-0x000000820000 : "unused_area"
[ 1.027313] 0x0000007e0000-0x000000820000 : "devinfo"
[ 1.032542] 0x000000900000-0x000008400000 : "kernel1"
[ 1.037994] 0x000000c00000-0x000008400000 : "ubi"
[ 1.043103] 0x000008400000-0x00000ff00000 : "kernel2"
[ 1.048551] 0x000008700000-0x00000ff00000 : "rootfs2"
[ 1.054015] 0x00000ff00000-0x000010000000 : "BBT"
[ 1.059164] libphy: Fixed MDIO Bus: probed
[ 1.063540] libphy: orion_mdio_bus: probed
[ 1.067798] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
[ 1.076431] mvneta f1070000.ethernet eth0: Using hardware mac address 60:38:e0:ce:3a:00
[ 1.085614] mvneta f1034000.ethernet eth1: Using hardware mac address 60:38:e0:ce:3a:00
[ 1.093797] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.100360] ehci-pci: EHCI PCI platform driver
[ 1.104843] ehci-platform: EHCI generic platform driver
[ 1.110149] ehci-orion: EHCI orion driver
[ 1.114250] orion-ehci f1058000.usb: EHCI Host Controller
[ 1.119681] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 1.127327] orion-ehci f1058000.usb: irq 38, io mem 0xf1058000
[ 1.159841] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 1.165979] hub 1-0:1.0: USB hub found
[ 1.169755] hub 1-0:1.0: 1 port detected
[ 1.174078] usbcore: registered new interface driver usb-storage
[ 1.180256] i2c /dev entries driver
[ 1.194993] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[ 1.207395] orion_wdt: Initial timeout 171 sec
[ 1.212087] sdhci: Secure Digital Host Controller Interface driver
[ 1.218294] sdhci: Copyright(c) Pierre Ossman
[ 1.271066] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.276513] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.289851] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA
[ 1.297361] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.309229] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 1.316765] NET: Registered protocol family 10
[ 1.321780] Segment Routing with IPv6
[ 1.325480] NET: Registered protocol family 17
[ 1.329967] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.343086] 8021q: 802.1Q VLAN Support v1.8
[ 1.347320] Registering SWP/SWPB emulation handler
[ 1.353514] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.358860] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 2
[ 1.366459] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 1.375745] xhci-hcd f10f8000.usb3: irq 44, io mem 0xf10f8000
[ 1.381779] hub 2-0:1.0: USB hub found
[ 1.385570] hub 2-0:1.0: 1 port detected
[ 1.389604] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.394958] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3
[ 1.402497] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
[ 1.409010] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.417310] hub 3-0:1.0: USB hub found
[ 1.421101] hub 3-0:1.0: 1 port detected
[ 1.425420] UBI: auto-attach mtd6
[ 1.428755] ubi0: attaching mtd6
[ 1.439377] random: fast init done
[ 1.452974] mmc0: new high speed SDIO card at address 0001
[ 1.867406] ubi0: scanning is finished
[ 1.876822] ubi0: attached mtd6 (name "ubi", size 120 MiB)
[ 1.882339] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.889243] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.896064] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.903058] ubi0: good PEBs: 960, bad PEBs: 0, corrupted PEBs: 0
[ 1.909090] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 1.916347] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 810223659
[ 1.925435] ubi0: available PEBs: 0, total reserved PEBs: 960, PEBs reserved for bad PEB handling: 40
[ 1.934711] ubi0: background thread "ubi_bgt0d" started, PID 712
[ 1.941017] block ubiblock0_0: created from ubi0:0(rootfs)
[ 1.946527] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 1.953701] mvsw61xx 10.mvsw61xx: Found MV88E6352 at f1072004.mdio-mii:10
[ 1.960528] mvsw61xx 10.mvsw61xx: Using direct addressing
[ 1.972827] hctosys: unable to open rtc device (rtc0)
[ 1.980309] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 1.987948] Freeing unused kernel memory: 1024K
[ 2.150520] init: Console is alive
[ 2.153999] init: - watchdog -
[ 2.426091] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.459791] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.469073] init: - preinit -
[ 2.604233] mvneta f1070000.ethernet tmp0: renamed from eth0
[ 2.610094] random: procd: uninitialized urandom read (4 bytes read)
[ 2.651108] mvneta f1034000.ethernet eth0: renamed from eth1
[ 2.691068] mvneta f1070000.ethernet eth1: renamed from tmp0
[ 2.934265] random: jshn: uninitialized urandom read (4 bytes read)
[ 2.949637] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.117856] mvneta f1034000.ethernet eth0: configuring for fixed/sgmii link mode
[ 3.125650] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3.131673] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 3.139567] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
f
[ 6.209938] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 822
[ 6.237961] UBIFS (ubi0:1): recovery needed
[ 6.267946] random: crng init done
[ 6.271361] random: 3 urandom warning(s) missed due to ratelimiting
[ 6.315983] UBIFS (ubi0:1): recovery completed
[ 6.320474] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 6.328339] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 6.338303] UBIFS (ubi0:1): FS size: 111611904 bytes (106 MiB, 879 LEBs), journal size 5586944 bytes (5 MiB, 44 LEBs)
[ 6.348962] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[ 6.355609] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 558F5CB8-F8C3-4C8E-8E4D-0C1734333040, small LPT model
[ 6.369545] mount_root: switching to ubifs overlay
ubiattach: option requires an argument: m
Use -h for help
ubifs syscfg partition is damaged, reformatting
ubidetach: option requires an argument: m
Use -h for help
libmtd: error!: cannot get information about [ 6.452791] urandom-seed: Seeding with /etc/urandom.seed
"/dev/mtd"
error 2 (No such file or directory)
ubiformat: error!: cannot get information about "/dev/mtd"
error 2 (No such file or directory)
ubiattach: option requires an argument: m
Use -h for help
libubi: error!: cannot get information about "/dev/ubi1"
error 2 (No such file or dire[ 6.485698] mvneta f1034000.ethernet eth0: Link is Down
ctory)
ubimkvol: error!: error while probing "/dev/ubi1"
error 2 (No such file or directory)
mount: mounting ubi1:syscfg on /tmp/syscfg failed: No such device
[ 6.541545] procd: - early -
[ 6.544458] procd: - watchdog -
[ 7.144629] procd: - watchdog -
[ 7.147863] procd: - ubus -
[ 7.215548] procd: - init -
Please press Enter to activate this console.
[ 7.320436] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.329113] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.335759] Loading modules backported from Linux version v4.19.120-0-gfdc072324f3c
[ 7.339009] urngd: v1.0.2 started.
[ 7.343467] Backport generated by backports.git v4.19.120-1-0-g60c3a249
[ 7.374967] <<Marvell Mac80211 Wireless PCIE Network Driver version 10.3.8.0-20181210>>
[ 7.383038] pci 0000:00:01.0: enabling device (0140 -> 0142)
[ 10.455870] ieee80211 phy0: device node: /soc/pcie/pcie@1,0
[ 10.488856] ieee80211 phy0: firmware version: 0x9030206
[ 10.795847] ieee80211 phy0: firmware region code: 30
[ 10.834642] ieee80211 phy0: 2G disabled, 5G enabled
[ 10.839550] ieee80211 phy0: 4 TX antennas, 4 RX antennas
[ 10.845080] pci 0000:00:02.0: enabling device (0140 -> 0142)
[ 12.209883] ieee80211 phy1: device node: /soc/pcie/pcie@2,0
[ 12.242935] ieee80211 phy1: firmware version: 0x9030206
[ 12.549834] ieee80211 phy1: firmware region code: 30
[ 12.582687] ieee80211 phy1: 2G enabled, 5G disabled
[ 12.587599] ieee80211 phy1: 4 TX antennas, 4 RX antennas
[ 12.595129] hidraw: raw HID events driver (C) Jiri Kosina
[ 12.604055] Bluetooth: Core ver 2.22
[ 12.607701] NET: Registered protocol family 31
[ 12.612181] Bluetooth: HCI device and connection manager initialized
[ 12.618573] Bluetooth: HCI socket layer initialized
[ 12.623495] Bluetooth: L2CAP socket layer initialized
[ 12.628594] Bluetooth: SCO socket layer initialized
[ 12.633933] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 12.639277] Bluetooth: BNEP filters: protocol multicast
[ 12.644562] Bluetooth: BNEP socket layer initialized
[ 12.650769] Bluetooth: vendor=0x2df, device=0x9136, class=255, fn=2
[ 13.365966] Bluetooth: FW download over, size 616840 bytes
[ 13.979865] sdio platform data not available
[ 13.980595] usbcore: registered new interface driver btusb
[ 13.990964] Bluetooth: HCI UART driver ver 2.3
[ 13.995427] Bluetooth: HCI UART protocol H4 registered
[ 14.000599] Bluetooth: HCI UART protocol BCSP registered
[ 14.005933] Bluetooth: HCI UART protocol ATH3K registered
[ 14.011740] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 14.017691] Bluetooth: HIDP socket layer initialized
[ 14.023124] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.033467] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 14.040731] mwifiex_sdio mmc0:0001:1: WLAN FW already running! Skip FW dnld
[ 14.047728] mwifiex_sdio mmc0:0001:1: WLAN FW is active
[ 14.056787] Bluetooth: RFCOMM TTY layer initialized
[ 14.061737] Bluetooth: RFCOMM socket layer initialized
[ 14.066912] Bluetooth: RFCOMM ver 1.11
[ 14.071095] mwifiex_sdio mmc0:0001:1: Unknown api_id: 4
[ 14.074208] xt_time: kernel timezone is -0000
[ 14.082575] PPP generic driver version 2.4.2
[ 14.087217] NET: Registered protocol family 24
[ 14.092419] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 14.109362] mwifiex_sdio mmc0:0001:1: info: MWIFIEX VERSION: mwifiex 1.0 (15.68.7.p189)
[ 14.117574] mwifiex_sdio mmc0:0001:1: driver_version = mwifiex 1.0 (15.68.7.p189)
[ 15.348031] mvneta f1034000.ethernet eth0: configuring for fixed/sgmii link mode
[ 15.355580] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 15.361501] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 15.369382] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 15.384065] br-lan: port 1(eth0.1) entered blocking state
[ 15.389492] br-lan: port 1(eth0.1) entered disabled state
[ 15.395080] device eth0.1 entered promiscuous mode
[ 15.399908] device eth0 entered promiscuous mode
[ 15.405706] br-lan: port 1(eth0.1) entered blocking state
[ 15.411159] br-lan: port 1(eth0.1) entered forwarding state
[ 15.416918] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 15.429595] mvneta f1070000.ethernet eth1: configuring for fixed/rgmii-id link mode
[ 15.437839] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 15.444795] mvneta f1070000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 15.454629] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 16.409845] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Sponsor
blkt
DD-WRT Guru


Joined: 20 Jan 2019
Posts: 4134

PostPosted: Tue Aug 11, 2020 17:03    Post subject: Reply with quote
Silent boot is enabled, so it won't tell you when to press any key to interrupt the boot process to enter u-boot environment.

When you turn on the router just start playing the drums on the spacebar until you get in.

flat-FW_WRT32X_1.0.180404.58.img rename this to venom.img

"printenv" by itself will give you a full list of the environment variables, save a copy for future reference.

You can also make specific queries.

printenv ipaddr
printenv serverip
printenv netmask
printenv firmwareName
printenv bootdelay
printenv silent

https://the.earth.li/~sgtatham/putty/latest/w32/putty.zip

https://bitbucket.org/phjounin/tftpd64/downloads/tftpd32.464.zip
RedDragon23
DD-WRT Novice


Joined: 11 Aug 2020
Posts: 5

PostPosted: Tue Aug 11, 2020 17:33    Post subject: Reply with quote
Thanks you. nothing I press/type in seems to work. I get no feedback whatsoever, just the 'debug' log coming through.

High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.46.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Not detected suspend to RAM indication
BootROM: Image checksum verification PASSED


U-Boot 2013.01 (May 18 2017 - 16:37:44) Marvell version: 2015_T1.QA.0p16

Boot version : v2.0.9

Board: RD-NAS-88F6820-DDR3
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1866 [MHz]
L2 @ 933 [MHz]
TClock @ 200 [MHz]
DDR3 @ 933 [MHz]
DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 512 MiB
NAND: 256 MiB
MMC: mv_sdh: 0

Here's the top part, because for some reason with the RX (Whichever the white on is again) plugged in on boot there's no lights on the system at all, but if I brefily remove it and plug it straight back in again then I get stuff through Putty otherwise just a black screen for me.
blkt
DD-WRT Guru


Joined: 20 Jan 2019
Posts: 4134

PostPosted: Tue Aug 11, 2020 17:53    Post subject: Reply with quote
USB to TTL Tips - HOW TO FIX Garbage/Garbled PuTTY output

https://openwrt.org/toh/linksys/wrt_ac_series#serial_flash

What kind of USB to TTL Serial 3.3V adapter are you using? On my cable green is RX, white is TX, but maybe yours is different?

https://www.amazon.com/Serial-Adapter-Signal-FT232RL-Windows/dp/B07RBKCW3S

https://openwrt.org/toh/linksys/wrt_ac_series#serial_port

https://openwrt.org/_detail/media/linksys/wrt3200acm/wrt3200acm_serial_header.jpg?id=toh%3Alinksys%3Alinksys_wrt32x

The pins are smaller in size than standard, so you may need to improvise to keep yours connected.
RedDragon23
DD-WRT Novice


Joined: 11 Aug 2020
Posts: 5

PostPosted: Thu Aug 13, 2020 12:18    Post subject: Reply with quote
blkt wrote:
USB to TTL Tips - HOW TO FIX Garbage/Garbled PuTTY output

https://openwrt.org/toh/linksys/wrt_ac_series#serial_flash

What kind of USB to TTL Serial 3.3V adapter are you using? On my cable green is RX, white is TX, but maybe yours is different?

https://www.amazon.com/Serial-Adapter-Signal-FT232RL-Windows/dp/B07RBKCW3S

https://openwrt.org/toh/linksys/wrt_ac_series#serial_port

https://openwrt.org/_detail/media/linksys/wrt3200acm/wrt3200acm_serial_header.jpg?id=toh%3Alinksys%3Alinksys_wrt32x

The pins are smaller in size than standard, so you may need to improvise to keep yours connected.


I've spent some time investigating. I've finally got into Venom>> and I flashed the image over successfully, however it won't boot into the stock firmware. I can still get back into Venom and when I type in Boot, it throws this error, which I don't fully understand since I followed the instructions by using the Flat Firmware Image via serial and tftpd.

thanks
blkt
DD-WRT Guru


Joined: 20 Jan 2019
Posts: 4134

PostPosted: Thu Aug 13, 2020 12:21    Post subject: Reply with quote
If you are sure it has flashed succesfully, just hold the red reset button for 10 seconds and then it should boot right up.
RedDragon23
DD-WRT Novice


Joined: 11 Aug 2020
Posts: 5

PostPosted: Thu Aug 13, 2020 12:22    Post subject: Reply with quote
blkt wrote:
If you are sure it has flashed succesfully, just hold the red reset button for 10 seconds and then it should boot right up.


I get this error when I run Boot command
"Bad Linux ARM zImage magic!"
blkt
DD-WRT Guru


Joined: 20 Jan 2019
Posts: 4134

PostPosted: Thu Aug 13, 2020 12:32    Post subject: Reply with quote
I don't have enough information from you to give a direct answer.

If you are absolutely sure the flash procedure was successful (usb to ttl serial adapter driver properly installed and configured, com ports configured correctly, u-boot environment variable settings correct, ethernet adapter settings correct, tftp settings, putty settings, ran the correct u-boot commands e.g. run update_both_images) then another possibility is a corrupt u-boot environment.

Always first run "printenv" by itself to obtain a full list, then copy all to a text file for future reference. Then, you can restore the environment defaults with the following commands.

env default -a
saveenv
reset

Run printenv again, copy the list into a new text file then you can compare.

A few variables might go missing, such as SMT-2D and mv_pon_addr, but since you have a backup from the original printenv anything can be added back with setenv (when finished run saveenv then reset).

If your u-boot partitions are really toast the recovery method is here.


Last edited by blkt on Thu Aug 13, 2020 17:00; edited 7 times in total
RedDragon23
DD-WRT Novice


Joined: 11 Aug 2020
Posts: 5

PostPosted: Thu Aug 13, 2020 12:36    Post subject: Reply with quote
Thank you so much for your help. Sorry, My bad, I forgot to clear the cache on my browser -_- And the Bad Boot Image was my fault, I tried the flat firmware and not getting anywhere I was experimenting with flashing DD-WRT firmware directly, which meant it didn't boot and threw that error.
Stock Firmware is now on and working Very Happy Finally...
I think i've kinda know all the steps off by heart now.
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum